LTC4444IMS8E-TRPBF

LTC4444 High Voltage Synchronous N-Channel MOSFET Driver FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTION The LTC®4444 is a high frequency high voltage gate driver that drives two N-channel MOSFETs in a synchronous DC/DC converter with supply voltages up to 100V. The powerful driver capability reduces switching losses in MOSFETs with high gate capacitance. The LTC4444’s pull-up for the top gate driver has a peak output current of 2.5A and its pull-down has an output impedance of 1.2Ω. The pull-up for the bottom gate driver has a peak output current of 3A and the pull-down has an output impedance of 0.55Ω. The LTC4444 is configured for two supply-independent inputs. The high side input logic signal is internally level-shifted to the bootstrapped supply, which may function at up to 114V above ground. The LTC4444 contains undervoltage lockout circuits that disable the external MOSFETs when activated. The LTC4444 also contains adaptive shoot-through protection to prevent both MOSFETs from conducting simultaneously. The LTC4444 is available in the thermally enhanced 8-lead MSOP package. , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 6677210. Bootstrap Supply Voltage to 114V Wide VCC Voltage: 7.2V to 13.5V Adaptive Shoot-Through Protection 2.5A Peak TG Pull-Up Current 3A Peak BG Pull-Up Current 1.2Ω TG Driver Pull-Down 0.55Ω BG Driver Pull-Down 5ns TG Fall Time Driving 1nF Load 8ns TG Rise Time Driving 1nF Load 3ns BG Fall Time Driving 1nF Load 6ns BG Rise Time Driving 1nF Load Drives Both High and Low Side N-Channel MOSFETs Undervoltage Lockout Thermally Enhanced 8-Pin MSOP Package APPLICATIONS ■ ■ ■ ■ Distributed Power Architectures Automotive Power Supplies High Density Power Modules Telecommunications TYPICAL APPLICATION High Input Voltage Buck Converter VCC 7.2V TO 13.5V BOOST VCC PWM1 (FROM CONTROLLER IC) PWM2 (FROM CONTROLLER IC) TINP BINP GND 4444 TA01a LTC4444 Driving a 1000pF Capacitive Load BINP 5V/DIV BG 10V/DIV TINP 5V/DIV TG-TS 10V/DIV 20ns/DIV 4444 TA01b VIN 100V (ABS MAX) TG LTC4444 TS BG VOUT 4444f 1 LTC4444 ABSOLUTE MAXIMUM RATINGS (Note 1) PIN CONFIGURATION TOP VIEW TINP BINP VCC BG 1 2 3 4 8 7 6 5 TS TG BOOST NC 9 Supply Voltage VCC......................................................... –0.3V to 14V BOOST – TS ........................................... –0.3V to 14V TINP Voltage ................................................. –2V to 14V BINP Voltage ................................................. –2V to 14V BOOST Voltage ........................................ –0.3V to 114V TS Voltage................................................... –5V to 100V Operating Temperature Range (Note 2) ... –40°C to 85°C Junction Temperature (Note 3) ............................. 125°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C MS8E PACKAGE 8-LEAD PLASTIC MSOP TJMAX = 125°C, θJA = 40°C/W, θJC = 10°C/W (NOTE 4) EXPOSED PAD (PIN 9) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH LTC4444EMS8E#PBF LTC4444IMS8E#PBF TAPE AND REEL LTC4444EMS8E#TRPBF LTC4444IMS8E#TRPBF PART MARKING* LTDBF LTDBF PACKAGE DESCRIPTION 8-Lead Plastic MSOP 8-Lead Plastic MSOP TEMPERATURE RANGE –40°C to 85°C –40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VBOOST = 12V, VTS = GND = 0V, unless otherwise noted. SYMBOL VCC IVCC UVLO PARAMETER Operating Voltage DC Supply Current Undervoltage Lockout Threshold TINP = BINP = 0V VCC Rising VCC Falling Hysteresis TINP = BINP = 0V BINP Ramping High BINP Ramping Low TINP Ramping High TINP Ramping Low ● ● ● ● ● ● ELECTRICAL CHARACTERISTICS Gate Driver Supply, VCC CONDITIONS MIN 7.2 TYP MAX 13.5 UNITS V μA V V mV μA V V V V μA 350 6.00 5.60 6.60 6.15 450 0.1 2.25 1.85 2.25 1.85 2.75 2.3 2.75 2.3 ±0.01 550 7.20 6.70 Bootstrapped Supply (BOOST – TS) IBOOST VIH(BG) VIL(BG) VIH(TG) VIL(TG) ITINP(BINP) DC Supply Current BG Turn-On Input Threshold BG Turn-Off Input Threshold TG Turn-On Input Threshold TG Turn-Off Input Threshold Input Pin Bias Current 2 3.25 2.75 3.25 2.75 ±2 Input Signal (TINP, BINP) 4444f 2 LTC4444 The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VCC = VBOOST = 12V, VTS = GND = 0V, unless otherwise noted. SYMBOL VOH(TG) VOL(TG) IPU(TG) RDS(TG) VOH(BG) VOL(BG) IPU(BG) RDS(BG) tPLH(TG) tPHL(TG) tPLH(BG) tPHL(BG) tr(TG) tf(TG) tr(BG) tf(BG) PARAMETER TG High Output Voltage TG Low Output Voltage TG Peak Pull-Up Current TG Pull-Down Resistance BG High Output Voltage BG Low Output Voltage BG Peak Pull-Up Current BG Pull-Down Resistance TG Low-High Propagation Delay TG High-Low Propagation Delay BG Low-High Propagation Delay BG High-Low Propagation Delay TG Output Rise Time TG Output Fall Time BG Output Rise Time BG Output Fall Time 10% – 90%, CL = 1nF 10% – 90%, CL = 10nF 10% – 90%, CL = 1nF 10% – 90%, CL = 10nF 10% – 90%, CL = 1nF 10% – 90%, CL = 10nF 10% – 90%, CL = 1nF 10% – 90%, CL = 10nF IBG = –10mA, VOH(BG) = VCC – VBG IBG = 100mA ● ● ● ● ● ● ● ELECTRICAL CHARACTERISTICS High Side Gate Driver Output (TG) CONDITIONS ITG = –10mA, VOH(TG) = VBOOST – VTG ITG = 100mA, VOL(TG) = VTG –VTS ● ● ● MIN TYP 0.7 120 MAX UNITS V 220 2.2 mV A Ω V 1.7 2.5 1.2 0.7 55 110 1.1 45 40 35 30 Low Side Gate Driver Output (BG) mV A Ω ns ns ns ns ns ns ns ns ns ns ns ns 2 3 0.55 25 22 19 14 8 80 5 50 6 60 3 30 Switching Time (BINP (TINP) is Tied to Ground While TINP (BINP) is Switching. Refer to Timing Diagram) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4444E is guaranteed to meet specifications from 0°C to 85°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTC4444I is guaranteed over the full –40°C to 85°C operating temperature range. Note 3: TJ is calculated from the ambient temperature TA and power dissipation PD according to the following formula: TJ = TA + (PD • θJA°C/W) Note 4: Failure to solder the exposed back side of the MS8E package to the PC board will result in a thermal resistance much higher than 40°C/W. 4444f 3 LTC4444 TYPICAL PERFORMANCE CHARACTERISTICS VCC Supply Quiescent Current vs Voltage 450 400 QUIESCENT CURRENT (μA) 350 300 250 200 150 100 50 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VCC SUPPLY VOLTAGE (V) 4444 G01 BOOST-TS Supply Quiescent Current vs Voltage 400 350 QUIESCENT CURRENT (μA) 300 250 200 150 100 50 TINP = BINP = 0V 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 BOOST SUPPLY VOLTAGE (V) 4444 G02 VCC Supply Current vs Temperature 380 370 VCC SUPPLY CURRENT (μA) 360 TINP = BINP = 0V 350 340 330 TINP(BINP) = 12V 320 310 300 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G03 TA = 25°C BOOST = 12V TS = GND TINP = BINP = 0V TA = 25°C VCC = 12V TS = GND TINP = 12V, BINP = 0V VCC = BOOST = 12V TS = GND TINP(BINP) = 12V TINP = 0V, BINP = 12V Boost Supply Current vs Temperature 400 BOOST SUPPLY CURRENT (μA) 350 300 250 200 150 100 50 TINP = BINP = 0V 0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G04 Output Low Voltage (VOL) vs Supply Voltage 160 VOL(TG) TG OR BG OUTPUT VOLTAGE (V) 140 OUTPUT VOLTAGE (mV) 120 100 80 VOL(BG) 60 40 20 0 7 8 11 12 10 SUPPLY VOLTAGE (V) 9 13 14 TA = 25°C ITG(BG) = 100mA BOOST = VCC TS = GND 15 14 13 12 11 10 9 8 7 6 5 Output High Voltage (VOH) vs Supply Voltage TA = 25°C BOOST = VCC TS = GND VCC = BOOST = 12V TS = GND TINP = 12V BINP = 0V TINP = 0V BINP = 12V –1mA –10mA –100mA 7 8 11 10 9 12 SUPPLY VOLTAGE (V) 13 14 444343 G05 4444 G06 Input Thresholds (TINP, BINP) vs Supply Voltage 3.1 3.0 TG OR BG INPUT THRESHOLD (V) 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 7 8 11 10 9 12 SUPPLY VOLTAGE (V) 13 14 VIL(TG,BG ) TG OR BG INPUT THRESHOLD (V) TA = 25°C BOOST = VCC TS = GND VIH(TG,BG) 3.0 Input Thresholds (TINP, BINP) vs Temperature TG OR BG INPUT THRESHOLD HYSTERESIS (mV) VCC = BOOST = 12V 2.9 TS = GND 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2.0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G08 Input Thresholds (TINP, BINP) Hysteresis vs Voltage 500 TA = 25°C VCC = BOOST = 12V TS = GND VIH(TG,BG) 475 450 VIL(TG,BG) 425 400 375 7 8 11 10 9 12 SUPPLY VOLTAGE (V) 13 14 4444 G07 4444 G09 4444f 4 LTC4444 TYPICAL PERFORMANCE CHARACTERISTICS Input Thresholds (TINP, BINP) Hysteresis vs Temperature TG OR BG INPUT THRESHOLD HYSTERESIS (mV) 500 VCC = BOOST = 12V TS = GND VCC SUPLLY VOLTAGE (V) 6.7 6.6 6.5 6.4 6.3 6.2 6.1 375 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G10 VCC Undervoltage Lockout Thresholds vs Temperature BOOST = VCC TS = GND RISING THRESHOLD RISE/FALL TIME (ns) 32 30 28 26 24 22 20 18 16 14 12 10 8 6 Rise and Fall Time vs VCC Supply Voltage TA = 25°C BOOST = VCC TS = GND CL = 3.3nF 475 tr(TG) 450 tr(BG) 425 FALLING THRESHOLD tf(TG) 400 tf(BG) 7 8 11 10 9 12 SUPPLY VOLTAGE (V) 13 14 6.0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G11 4444 G12 Rise and Fall Time vs Load Capacitance 80 70 RISE/FALL TIME (ns) 60 50 tr(BG) 40 30 20 10 0 1 2 tf(BG) 5 6 3 4 7 8 LOAD CAPACITANCE (nF) 9 10 tf(TG) TA = 25°C VCC = BOOST = 12V TS = GND PULL-UP CURRENT (A) tr(TG) 3.4 3.2 3.0 2.8 2.6 Peak Driver (TG, BG) Pull-Up Current vs Temperature VCC = BOOST = 12V TS = GND IPU(BG) OUTPUT DRIVER PULL-DOWN RESISTACNE (Ω) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 Output Driver Pull-Down Resistance vs Temperature BOOST-TS = 12V BOOST-TS = 7V RDS(TG) BOOST-TS = 14V VCC = 12V VCC = 7V VCC = 14V RDS(BG) IPU(TG) 2.4 2.2 2.0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G14 0 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G15 4444 G13 Propagation Delay vs VCC Supply Voltage 30 28 PROPAGATION DELAY (ns) 26 24 22 20 18 16 14 12 10 7 8 11 10 9 12 SUPPLY VOLTAGE (V) 13 14 tPHL(BG) tPHL(TG) tPLH(BG) tPLH(TG) TA = 25°C BOOST = VCC TS = GND PROPAGATION DELAY (ns) 37 32 27 22 Propagation Delay vs Temperature VCC = BOOST = 12V TS = GND tPLH(TG) tPHL(TG) tPLH(BG) 17 tPHL(BG) 12 7 2 –40 –25 –10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 4444 G17 4444 G16 4444f 5 LTC4444 TYPICAL PERFORMANCE CHARACTERISTICS Switching Supply Current vs Input Frequency TA = 25°C = BOOST = 12V 3.5 VCC TS = GND SUPPLY CURRENT (mA) 3.0 2.5 2.0 1.5 1.0 0.5 0 IBOOST (BG SWITCHING) 0 200 400 800 600 SWITCHING FREQUENCY (kHz) 1000 4444 G18 Switching Supply Current vs Load Capacitance IVCC (BG SWITCHING AT 1MHz) IBOOST (TG SWITCHING AT 500kHz) 4.0 IVCC (BG SWITCHING) SUPPLY CURRENT (mA) IBOOST (TG SWITCHING) 100 10 IVCC (TG SWITCHING) 1 IBOOST (TG SWITCHING IVCC AT 1MHz) (BG SWITCHING AT 500kHz) IVCC IVCC (TG SWITCHING (TG SWITCHING AT 500kHz) AT 1MHz) IBOOST (BG SWITCHING AT 1MHz OR 5OOkHz) 0.1 1 2 3 4 5 6 7 8 LOAD CAPACITANCE (nF) 9 10 """" /' PIN FUNCTIONS TINP (Pin 1): High Side Input Signal. Input referenced to GND. This input controls the high side driver output (TG). BINP (Pin 2): Low Side Input Signal. This input controls the low side driver output (BG). VCC (Pin 3): Supply. This pin powers input buffers, logic and the low side gate driver output directly and the high side gate driver output through an external diode connected between this pin and BOOST (Pin 6). A low ESR ceramic bypass capacitor should be tied between this pin and GND (Pin 9). BG (Pin 4): Low Side Gate Driver Output (Bottom Gate). This pin swings between VCC and GND. NC (Pin 5): No Connect. No connection required. BOOST (Pin 6): High Side Bootstrapped Supply. An external capacitor should be tied between this pin and TS (Pin 8). Normally, a bootstrap diode is connected between VCC (Pin 3) and this pin. Voltage swing at this pin is from VCC – VD to VIN + VCC – VD, where VD is the forward voltage drop of the bootstrap diode. TG (Pin 7): High Side Gate Driver Output (Top Gate). This pin swings between TS and BOOST. TS (Pin 8): High Side MOSFET Source Connection (Top Source). Exposed Pad (Pin 9): Ground. Must be soldered to PCB ground for optimal thermal performance. 4444f 6 LTC4444 BLOCK DIAGRAM 6 3 9 VCC GND HIGH SIDE LEVEL SHIFTER LDO VINT ANTISHOOT-THROUGH PROTECTION VCC BINP NC 5 4444 BD BOOST VCC UVLO TG TS VIN UP TO 100V 7.2V TO 13.5V 7 8 1 TINP VCC BG 4 2 LOW SIDE LEVEL SHIFTER TIMING DIAGRAM INPUT RISE/FALL TIME < 10ns TINP (BINP) BINP (TINP) BG (TG) 90% 10% 90% TG (BG) 10% tr tPHL 90% 10% tf tPLH 4444 TD OPERATION Overview The LTC4444 receives ground-referenced, low voltage digital input signals to drive two N-channel power MOSFETs in a synchronous buck power supply configuration. The gate of the low side MOSFET is driven either to VCC or GND, depending on the state of the input. Similarly, the gate of the high side MOSFET is driven to either BOOST or TS by a supply bootstrapped off of the switching node (TS). Input Stage The LTC4444 employs CMOS compatible input thresholds that allow a low voltage digital signal to drive standard power MOSFETs. The LTC4444 contains an internal voltage regulator that biases both input buffers for high side and low side inputs, allowing the input thresholds (VIH = 2.75V, VIL = 2.3V) to be independent of variations in VCC. The 450mV hysteresis between VIH and VIL eliminates false triggering due to noise during switching transitions. However, care should be taken to keep both input pins (TINP and BINP) from any noise pickup, especially in high frequency, high voltage applications. The LTC4444 input buffers have high input impedance and draw negligible input current, simplifying the drive circuitry required for the inputs. 4444f 7 LTC4444 OPERATION Output Stage A simplified version of the LTC4444’s output stage is shown in Figure 1. The pull-up devices on the BG and TG outputs are NPN bipolar junction transistors (Q1 and Q2). The BG and TG outputs are pulled up to within an NPN VBE (~0.7V) of their positive rails (VCC and BOOST, respectively). Both BG and TG have N-channel MOSFET pull-down devices (M1 and M2) which pull BG and TG down to their negative rails, GND and TS. The large voltage swing of the BG and TG output pins is important in driving external power MOSFETs, whose RDS(ON) is inversely proportional to the gate overdrive voltage (VGS − VTH). Rise/Fall Time The LTC4444’s rise and fall times are determined by the peak current capabilities of Q1 and M1. The predriver that drives Q1 and M1 uses a nonoverlapping transition scheme to minimize cross-conduction currents. M1 is fully turned off before Q1 is turned on and vice versa. Since the power MOSFET generally accounts for the majority of the power loss in a converter, it is important to quickly turn it on or off, thereby minimizing the transition time in its linear region. An additional benefit of a strong pull-down on the driver outputs is the prevention of crossconduction current. For example, when BG turns the low side (synchronous) power MOSFET off and TG turns the high side power MOSFET on, the voltage on the TS pin will rise to VIN very rapidly. This high frequency positive voltage transient will couple through the CGD capacitance of the low side power MOSFET to the BG pin. If there is an insufficient pull-down on the BG pin, the voltage on the BG pin can rise above the threshold voltage of the low side power MOSFET, momentarily turning it back on. With both the high side and low side MOSFETs conducting, significant cross-conduction current will flow through the MOSFETs from VIN to ground and will cause substantial power loss. A similar effect occurs on TG due to the CGS and CGD capacitances of the high side MOSFET. The powerful output driver of the LTC4444 reduces the switching losses of the power MOSFET, which increase with transition time. The LTC4444’s high side driver is Figure 1. Capacitance Seen by BG and TG During Switching LTC4444 BOOST 6 Q1 VIN UP TO 100V TG 7 CGD M1 TS 8 CGS HIGH SIDE POWER MOSFET LOAD INDUCTOR VCC 3 Q2 CGD BG 4 M2 GND 9 CGS LOW SIDE POWER MOSFET capable of driving a 1nF load with 8ns rise and 5ns fall times using a bootstrapped supply voltage VBOOST-TS of 12V while its low side driver is capable of driving a 1nF load with 6ns rise and 3ns fall times using a supply voltage VCC of 12V. Undervoltage Lockout (UVLO) The LTC4444 contains an undervoltage lockout detector that monitors VCC supply. When VCC falls below 6.15V, the output pins BG and TG are pulled down to GND and TS, respectively. This turns off both external MOSFETs. When VCC has adequate supply voltage, normal operation will resume. Adaptive Shoot-Through Protection Internal adaptive shoot-through protection circuitry monitors the voltages on the external MOSFETs to ensure that they do not conduct simultaneously. This feature improves efficiency by eliminating cross-conduction current from flowing from the VIN supply through both of the MOSFETs to ground during a switch transition. The adaptive shootthrough protection circuitry also monitors the level of the TS pin. If the TS pin stays high, BG will be turned on 150ns after TG is turned off. 4444f 8 LTC4444 APPLICATIONS INFORMATION Power Dissipation To ensure proper operation and long-term reliability, the LTC4444 must not operate beyond its maximum temperature rating. Package junction temperature can be calculated by: TJ = TA + PD (θJA) where: TJ = Junction temperature TA = Ambient temperature PD = Power dissipation θJA = Junction-to-ambient thermal resistance Power dissipation consists of standby and switching power losses: PD = PDC + PAC + PQG where: PDC = Quiescent power loss PAC = Internal switching loss at input frequency, fIN PQG = Loss due turning on and off the external MOSFET with gate charge QG at frequency fIN The LTC4444 consumes very little quiescent current. The DC power loss at VCC = 12V and VBOOST-TS = 12V is only (350μA)(12V) = 4.2mW. At a particular switching frequency, the internal power loss increases due to both AC currents required to charge and discharge internal node capacitances and cross-conduction currents in the internal logic gates. The sum of the quiescent current and internal switching current with no load are shown in the Typical Performance Characteristics plot of Switching Supply Current vs Input Frequency. The gate charge losses are primarily due to the large AC currents required to charge and discharge the capacitance of the external MOSFETs during switching. For identical pure capacitive loads CLOAD on TG and BG at switching frequency fIN, the load losses would be: PCLOAD = (CLOAD)(f)[(VBOOST-TS)2 + (VCC)2] In a typical synchronous buck configuration, VBOOST-TS is equal to VCC – VD, where VD is the forward voltage drop across the diode between VCC and BOOST. If this drop is small relative to VCC, the load losses can be approximated as: PCLOAD = 2(CLOAD)(fIN)(VCC)2 Unlike a pure capacitive load, a power MOSFET’s gate capacitance seen by the driver output varies with its VGS voltage level during switching. A MOSFET’s capacitive load power dissipation can be calculated using its gate charge, QG. The QG value corresponding to the MOSFET’s VGS value (VCC in this case) can be readily obtained from the manufacturer’s QG vs VGS curves. For identical MOSFETs on TG and BG: PQG = 2(VCC)(QG)(fIN) To avoid damage due to power dissipation, the LTC4444 includes a temperature monitor that will pull BG and TG low if the junction temperature rises above 160°C. Normal operation will resume when the junction temperature cools to less than 135°C. Bypassing and Grounding The LTC4444 requires proper bypassing on the VCC and VBOOST-TS supplies due to its high speed switching (nanoseconds) and large AC currents (Amperes). Careless component placement and PCB trace routing may cause excessive ringing. To obtain the optimum performance from the LTC4444: A. Mount the bypass capacitors as close as possible between the VCC and GND pins and the BOOST and TS pins. The leads should be shortened as much as possible to reduce lead inductance. B. Use a low inductance, low impedance ground plane to reduce any ground drop and stray capacitance. Remember that the LTC4444 switches greater than 3A peak currents and any significant ground drop will degrade signal integrity. 4444f 9 LTC4444 APPLICATIONS INFORMATION C. Plan the power/ground routing carefully. Know where the large load switching current is coming from and going to. Maintain separate ground return paths for the input pin and the output power stage. D. Keep the copper trace between the driver output pin and the load short and wide. E. Be sure to solder the Exposed Pad on the back side of the LTC4444 package to the board. Correctly soldered to a 2500mm2 doublesided 1oz copper board, the LTC4444 has a thermal resistance of approximately 40°C/W for the MS8E package. Failure to make good thermal contact between the exposed back side and the copper board will result in thermal resistances far greater than 40°C/W. TYPICAL APPLICATION LTC3780 High Efficiency 36V-72V VIN to 48V/6A Buck-Boost DC/DC Converter VBIAS 10V TO 12V 1μF 16V 3 1 68pF SENSE– 100Ω 2 3 4 0.1μF 100V VOS+ 487k 1% 5 8.25k 1% 6 7 8 D5 15k 220k VIN 9 10 11 12 PGOOD SS SENSE+ SENSE– ITH VOSENSE SGND RUN FCB PLLFLTR PLLIN STBYMD 0.1μF 16V 2.2μF, 100V, TDK C4532X7R2A225MT C1: SANYO 100ME100HC +T C2, C3: SANYO 63ME220HC + T D1: ON SEMI MMDL770T1G D2: DIODES INC. 1N5819HW-7-F BOOST1 24 23 22 21 20 19 18 17 16 15 14 13 6V 0.1μF 16V SENSE+ 10Ω R1 0.025Ω 1W R2 0.025Ω 1W 4444 TA02a 6V 10k 0.022μF 1000pF 220k 100pF SENSE+ 100Ω D2 VBIAS 10V TO 12V D1 2.2μF + 100V ×4 VIN C1 100μF 100V 1 2 4 LTC3780EG TG1 SW1 VIN EXTVCC INTVCC BG1 PGND BG2 SW2 TG2 BOOST2 6 BOOST LTC4444 7 BINP TG TINP BG GND 9 TS 8 VCC 0.1μF 16V 6V 10μF 10V 1μF 16V 0.22μF 16V VOS+ 10Ω 47pF L1 10μH D3 D4 2.2μF + 100V ×8 VOUT C2,C3 220μF 63V ×2 D6 D3, D4: DIODES INC. PDS560-13 D5: DIODES INC. MMBZ5230B-7-F D6: DIODES INC. B1100-13-F L1: SUMIDA CDEP147NP-100MC-125 R1, R2: VISHAY DALE WSL2512R0250FEA SENSE– 10Ω Efficiency 98 VIN = 36V VIN = 48V EFFICIENCY (%) 97 VIN = 72V 96 95 1 2 3 4 LOAD CURRENT (A) 5 6 4444 TA02b 4444f 10 LTC4444 PACKAGE DESCRIPTION MS8E Package 8-Lead Plastic MSOP, Exposed Die Pad (Reference LTC DWG # 05-08-1662 Rev D) BOTTOM VIEW OF EXPOSED PAD OPTION 1 2.06 ± 0.102 (.081 ± .004) 1.83 ± 0.102 (.072 ± .004) 2.794 ± 0.102 (.110 ± .004) 0.889 ± 0.127 (.035 ± .005) 5.23 (.206) MIN 2.083 ± 0.102 3.20 – 3.45 (.082 ± .004) (.126 – .136) 8 3.00 ± 0.102 (.118 ± .004) (NOTE 3) 0.42 ± 0.038 (.0165 ± .0015) TYP 0.65 (.0256) BSC 8 7 65 0.52 (.0205) REF RECOMMENDED SOLDER PAD LAYOUT DETAIL “A” 0° – 6° TYP 1 0.53 ± 0.152 (.021 ± .006) DETAIL “A” 0.18 (.007) SEATING PLANE 0.22 – 0.38 (.009 – .015) TYP 0.1016 ± 0.0508 (.004 ± .002) MSOP (MS8E) 0307 REV D 0.254 (.010) GAUGE PLANE 4.90 ± 0.152 (.193 ± .006) 3.00 ± 0.102 (.118 ± .004) (NOTE 4) 23 4 0.86 (.034) REF 1.10 (.043) MAX NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.65 (.0256) BSC 4444f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC4444 TYPICAL APPLICATION LTC3780 High Efficiency 8V-80V VIN to 12V/5A Buck-Boost DC/DC Converter VBIAS 12V 6V 10k 0.1μF 0.01μF 20k SENSE– SENSE+ 100Ω 68pF 100Ω 1 2 3 4 0.1μF VOS+ 113k 1% 5 8.06k 1% 6 7 8 9 D4 150k VIN 10 11 12 D2 24 23 22 21 20 19 18 17 16 15 14 13 6V 0.1μF 16V SENSE+ D5 10Ω 0.005Ω 1W 4444 TA03 0.22μF 16V VBIAS 12V 1μF 16V 3 D1 2.2μF + 100V ×5 VIN 100μF 100V ×2 PGOOD SS SENSE+ SENSE– ITH VOSENSE SGND RUN FCB PLLFLTR PLLIN STBYMD 0.1μF BOOST1 1 TG1 SW1 0.1μF 16V 6V 10μF 10V 1μF 16V 2 4 LTC3780EG TG1 SW1 VIN EXTVCC INTVCC BG1 PGND BG2 SW2 TG2 BOOST2 100pF 6 BOOST LTC4444 7 BINP TG TINP BG GND 9 TS 8 VCC 0.22μF 16V VOS+ 10Ω 22μF 16V ×3 SW1 + 47pF TG1 L1 8μH D3 VOUT C1 330μF ×2 2.2μF, 100V, TDK C4532X7R2A225MT 100μF, 100V SANYO 100ME 100AX C1: SANYO 16ME330WF D1: DIODES INC. BAV19WS D2: DIODES INC. 1N5819HW-7-F D3: DIODES INC. B320A-13-F D4: DIODES INC. MMBZ5230B-7-F D5: DIODES INC. B1100-13-F L1: SUMIDA CDEP147-8R0 SENSE– 10Ω RELATED PARTS PART NUMBER LTC1693 Family LT 1952/LTC3900 LT3010/LT3010-5 LTC3703 LTC3722-1/ LTC3722-2 LTC3723-1/ LTC3723-2 LTC3780 LTC3785 LTC3810 LTC3813 LT3845 LTC3901 LTC4440/ LTC4440-5 LTC4441 ® DESCRIPTION High Speed Dual MOSFET Drivers 36V to 72V Input Isolated DC/DC Converter Chip Sets COMMENTS 1.5A Peak Output Current, 4.5V ≤ VIN ≤ 13.2V Synchronous Rectification; Overcurrent, Overvoltage, UVLO Protection; Power Good Output Signal; Compact Solution No RSENSE™, Synchronizable Voltage Mode Control Adaptive Zero Voltage Switching, High Output Power Levels (Up to Kilowatts) Current Mode or Voltage Mode Push-Pull Controllers Four Switch, 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 30V, High Efficiency High Efficiency, Four Switch, 2.7V ≤ VIN ≤ 10V, 2.7V ≤ VOUT ≤ 10V 50mA, 3V to 80V Low Dropout Micropower Regulators Low Quiescent Current (30μA), Stable with Small (1μF) Ceramic Capacitor 100V Synchronous Switching Regulator Controller Synchronous Dual Mode Phase Modulated Full-Bridge Controllers Synchronous Push-Pull PWM Controllers High Power Buck-Boost Controller Buck-Boost Controller 100V Current Mode Synchronous Step-Down Switching No RSENSE, Synchronizable Tracking, Power Good Signal Regulator Controller 100V Current Mode Synchronous Step-Up Controller High Power Synchronous DC/DC Controller Secondary Side Synchronous Driver for Push-Pull and Full-Bridge Converters High Speed, High Voltage, High Side Gate Drivers 6A MOSFET Driver No RSENSE, On-Board 1Ω Gate Drivers, Synchronizable Current Mode Control, VIN Up to 60V, Low IQ Programmable Time Out, Reverse Inductor Current Sense Wide Operating VIN Range: Up to 80V DC, 100V Transient Adjustable Gate Drive from 5V to 8V, 5V ≤ VIN ≤ 28V 5A Peak Output Current, 6V to 9.5V Gate Drive Supply, 38V Max Input Supply 4444f LTC4442/LTC4442-1 High Speed Synchronous N-Channel MOSFET Drivers No RSENSE is a trademark of Linear Technology Corporation. 12 Linear Technology Corporation (408) 432-1900 ● FAX: (408) 434-0507 ● LT 1107 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007