0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
RH1086M

RH1086M

  • 厂商:

    LINER

  • 封装:

  • 描述:

    RH1086M - 0.5A and 1.5A Low Dropout Positive Adjustable Regulators - Linear Technology

  • 数据手册
  • 价格&库存
RH1086M 数据手册
RH1086M 0.5A and 1.5A Low Dropout Positive Adjustable Regulators DESCRIPTION The RH1086M positive adjustable regulator is designed to provide 0.5A for the H package and 1.5A for the K package with higher efficiency than currently available devices. All internal circuitry is designed to operate down to 1V inputoutput differential and the dropout voltage is fully specified as a function of load current. Dropout is guaranteed at a maximum of 1.5V at maximum output current, decreasing at lower load currents. On-chip trimming adjusts the output voltage to 1%. Current limit is also trimmed, minimizing the stress on both the regulator and power source circuitry under overload conditions. The RH1086M is pin compatible with older 3-terminal regulators. A 10μF output capacitor is required on this new device. However, this is usually included in most regulator designs. The wafer lots are processed to Linear Technology Corporation’s in-house Class S flow-to-yield circuits usable in stringent military applications. ABSOLUTE MAXIMUM RATINGS (Note 1) Power Dissipation ............................... Internally Limited Input-to-Output Voltage Differential ..........................25V Operating Junction Temperature Range Control Section ................................. – 55°C to 150°C Power Transistor................................ –55°C to 200°C Storage Temperature Range...................– 65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C PRECONDITIONING 100% Thermal Limit Burn-In L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. BURN-IN CIRCUIT RH1086M 15V IN ADJ OUT 150Ω RH1086 BI –15V CAPACITOR(S) NOT SHOWN PACKAGE INFORMATION BOTTOM VIEW VIN 2 CASE IS OUTPUT 1 ADJ K PACKAGE 2-LEAD TO-3 METAL CAN H PACKAGE 3-LEAD TO-39 METAL CAN 2 INPUT 1 3 OUTPUT (CASE) BOTTOM VIEW ADJ FINAL SPECIFICATIONS SUBJECT TO CHANGE Note: For ordering information contact LTC. rh1086mfc 1 RH1086M TABLE 1: ELECTRICAL CHARACTERISTICS PARAMETER Reference Voltage CONDITIONS IOUT = 10mA, (VIN – VOUT) = 3V (K) 10mA ≤ IOUT ≤ IFULL LOAD, 1.5V ≤ (VIN – VOUT) ≤ 25V Line Regulation Load Regulation Dropout Voltage Current Limit ILOAD = 10mA, 1.5V ≤ (VIN – VOUT) ≤ 15V (VIN – VOUT) = 3V, 10mA ≤ IOUT ≤ IFULL LOAD ΔVREF = 1%, IOUT = 1.5A (K) ΔVREF = 1%, IOUT = 0.5A (H) (VIN – VOUT) = 5V (K) (VIN – VOUT) = 5V (H) (VIN – VOUT) = 25V (K) (VIN – VOUT) = 25V (H) 6 2, 3 2, 3, 6 4 4 1.5 0.5 0.05 0.020 10 0.04 6 60 NOTES MIN 1.238 1.225 (Preirradiation) TA = 25°C SUBTYP MAX GROUP 1.262 1.270 0.2 0.3 1.5 1.25 1 1 1 1 1 1 1 1 1 4 4 60 5,6 1.5 0.5 0.05 0.020 10 1 1.225 1.270 0.2 0.4 1.5 1.25 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 –55°C ≤ TA ≤ 125°C SUBMIN TYP MAX GROUP UNITS V V % % V V A A A A mA %/W dB Minimum Load Current (VIN – VOUT) = 25V Thermal Regulation TA = 25°C, 30ms Pulse Ripple Rejection , f = 120Hz, CADJ = 25μF COUT = 25μF Tantalum, IOUT = IFULL LOAD, (VIN – VOUT) = 3V TJ = 25°C 10mA ≤ IOUT ≤ IFULL LOAD, 1.5V ≤ (VIN – VOUT) ≤ 15V TA = 125°C, 1000 Hours 10Hz ≤ f ≤ 10kHz Control Circuitry (K) Control Circuitry (H) Power Transistor (K) Power Transistor (H) 5 5 5 5 6 0.5 5 0.3 0.003 1.7 15.0 4.0 20.0 Adjust Pin Current Adjust Pin Current Change Temperature Stability Long Term Stability RMS Output Noise (% of VOUT) Thermal Resistance Junction-to-Case 55 120 5 1 1 0.5 120 5 2,3 2,3 μA μA % % % °C/W °C/W °C/W °C/W rh1086mfc 2 RH1086M TABLE 1A: ELECTRICAL CHARACTERISTICS PARAMETER Reference Voltage (Note 6) Line Regulation (Notes 2, 3) Load Regulation (Notes 2, 3, 6) Dropout Voltage (Note 4) Current Limit CONDITIONS 10mA ≤ IOUT ≤ IFULL LOAD 1.5V ≤ (VIN – VOUT) ≤ 15V IOUT = 10mA 1.5V ≤ (VIN – VOUT) ≤ 15V (VIN – VOUT) = 3V 10mA ≤ IOUT ≤ IFULL LOAD ΔVREF = 1%, IOUT = 1.5A (K) ΔVREF = 1%, IOUT = 0.5A (H) (VIN – VOUT ) = 5V (K) (VIN – VOUT ) = 25V (K) (VIN – VOUT ) = 5V (H) (VIN – VOUT ) = 25V (H) (VIN – VOUT ) = 25V 1.5 0.05 0.5 0.020 10 120 5 10KRAD (Si) MIN MAX 1.220 1.275 0.2 0.3 1.5 1.25 1.5 0.049 0.5 0.019 10 120 5 IOUT = 10mA (VIN – VOUT) = 3V (K) 1.234 1.262 (Postirradiation) TA = 25°C, unless otherwise noted. 50KRAD (Si) MIN MAX 100KRAD (Si) 200KRAD (Si) MIN MAX MIN MAX UNITS V V % % V V A A A A 10 120 5 mA μA μA 1.20 1.275 0.3 0.3 1.575 1.32 1.5 0.045 0.5 0.017 10 120 5 20KRAD (Si) MIN MAX 1.230 1.262 1.225 1.262 1.220 1.262 1.205 1.262 1.219 1.275 1.215 1.275 1.210 1.275 0.21 0.3 1.51 1.26 1.5 0.048 0.5 0.019 10 120 5 0.23 0.3 1.52 1.27 1.5 0.047 0.5 0.018 0.25 0.3 1.55 1.29 Minimum Load Current Adjust Pin Current Adjust Pin Current Change 10mA ≤ IOUT ≤ IFULL LOAD 1.5V ≤ (VIN – VOUT) ≤ 15V (Note 6) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Note 3: Line and load regulation are guaranteed up to the maximum power dissipation of 15W for RH1086MK and 3W for the RH1086MH. Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maximum power dissipation will not be available over the full input/output voltage range. Note 4: Dropout voltage is specified over the full output current range of the device. Test points and limits are shown on the Dropout Voltage curve in the LT®1086 data sheet. Note 5: Guaranteed by design, characterization, or correlation to other tested parameters. Note 6: IFULL LOAD is defined in the Current Limit curves in the standard data sheet. For compliance with 883 revision C current density specifications, the RH1086MK is derated to 1A. rh1086mfc 3 RH1086M TABLE 2: ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS Final Electrical Test Requirements (Method 5004) Group A Test Requirements (Method 5005) Group C and D End Point Electrical Parameters (Method 5005) *PDA applies to subgroup 1. See PDA Test Notes. SUBGROUP 1*,2,3,4,5,6 1,2,3,4,5,6 1 PDA Test Notes The PDA is specified as 5% based on failures from group A, subgroup 1, tests after cooldown as the final electrical test in accordance with method 5004 of MIL-STD-883 Class B. The verified failures of group A, subgroup 1, after burn-in divided by the total number of devices submitted for burn-in in that lot shall be used to determine the percent for the lot. Linear Technology Corporation reserves the right to test to tighter limits than those given. TOTAL DOSE BIAS CIRCUIT 15V VIN RH1086M ADJ VOUT 150Ω –15V RH1086 TA01 rh1086mfc 4 RH1086M TYPICAL PERFORMANCE CHARACTERISTICS Reference Voltage 1.26 10mA ≤ IOUT ≤ IFULL LOAD 1.5V ≤ (VIN – VOUT) ≤ 15V RIPPLE REJECTION (dB) 105 100 95 90 85 80 75 70 1.22 65 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G01 Ripple Rejection CURRENT LIMIT (K PACKAGE) (A) (VIN – VOUT) = 3V IOUT = IFULL LOAD 3.2 3.0 2.8 2.6 2.4 2.2 2.0 1.8 1.6 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G02 Current Limit (VIN – VOUT) = 5V 1.0 CURRENT LIMIT (H PACKAGE) (A) OUTPUT VOLTAGE (V) 1.25 1.24 0.8 1.23 0.6 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G03 Current Limit 0.15 CURRENT LIMIT (K PACKAGE) (A) (VIN – VOUT) = 25V 0.075 CURRENT LIMIT (H PACKAGE) (A) 0.3 Line Regulation 0.10 1.5V ≤ (VIN – VOUT) ≤ 15V IOUT = 10mA LOAD REGULATION (%) 0.05 Load Regulation (VIN – VOUT) = 3V 10mA ≤ IOUT ≤ 1.5A LINE REGULATION (%) 0.14 0.070 0.2 0.13 0.065 0.1 0 0.12 0.060 0 –0.05 0.11 1 10 100 TOTAL DOSE – KRADS (Si) 0.055 1000 RH1086 G04 –0.1 –0.10 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G05 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G06 Dropout Voltage 1.6 IOUT = 1.5A ADJUST PIN CURRENT (μA) 80 Adjust Pin Current (VIN – VOUT) = 3V 10mA ≤ IOUT ≤ IFULL LOAD MINIMUM LOAD CURRENT (mA) 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G08 Minimum Load Current 4 (VIN – VOUT) = 25V DROPOUT VOLTAGE (V) 1.4 70 3 1.2 60 2 1.1 50 1 1.0 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G07 40 0 1 10 100 TOTAL DOSE – KRADS (Si) 1000 RH1086 G09 rh1086mfc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 5 RH1086M REVISION HISTORY REV B C DATE 10/10 4/11 DESCRIPTION Updated Reference Voltage vs Postirradiation Limits in Table 1A: Electrical Characteristics Updated Dropout Voltage in Table 1 and Table 1A (Revision history begins at Rev B) PAGE NUMBER 3 2, 3 rh1086mfc 6 Linear Technology Corporation (408) 432-1900 ● FAX: (408) 434-0507 ● ID No. 66-11-1086 • LT 0411 REV C • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 www.linear.com © LINEAR TECHNOLOGY CORPORATION 1995
RH1086M 价格&库存

很抱歉,暂时无法提供与“RH1086M”相匹配的价格&库存,您可以联系我们找货

免费人工找货