Photocoupler
Product Data Sheet
6N135-L / 6N136-L series
Spec No.: DS70-2008-0032
Effective Date: 04/12/2016
Revision: A
LITE-ON DCC
RELEASE
BNS-OD-FC001/A4
LITE-ON Technology Corp. / Optoelectronics
No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.
Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660
http://www.liteon.com/opto
Photocoupler
6N135-L 6N136-L series
1. DESCRIPTION
The 6N135/ 6N136-L consists of a high efficient AlGaAs Light Emitting Diode and a high speed optical detector. This design
provides excellent AC and DC isolation between the input and output sides of the Optocoupler. Connection for the bias of the photodiode
improves the speed that of a conventional phototransistor coupler by reducing the base-collector capacitances. The internal shield
ensures high common mode transient immunity. A guaranteed common mode transient immunity is up to 1KV/μsec.
1.1 Features
High speed – 1MBd typical
Available in Dual-in-line, Wide lead spacing, Surface mounting package.
Storable output.
UL, CSA approval
1.2 Applications
Isolation in line receivers
Digital isolation for A/D, D/A conversion
Ground loop elimination
Feedback Element in Switching Mode Power Supplier
Pulse transformer replacement
Power transistor isolation in motor drives
Interface between Microprocessor system, computer and their peripheral
1.3 Functional Diagram
Truth Table (Positive Logic)
LED
OUT
ON
L
OFF
H
A 0.1μF bypass Capacitor must be connected between Pin8 and Pin5
1/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
2. PACKAGE DIMENSIONS
2.1 6N135-L
2.2 6N135M-L
2.3 6N135S-L
Notes :
1. Year date code.
2. 2-digit work week.
3. Factory identification mark shall be marked
(Y: Thailand , W: China-CZ)
4. For VDE option.
Dimensions in millimeters (inches).
2/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
2.4 6N136-L
2.5 6N136M-L
2.6 6N136S-L
Notes :
1. Year date code.
2. 2-digit work week.
3. Factory identification mark shall be marked
(Y: Thailand , W: China-CZ)
4. For VDE option.
Dimensions in millimeters (inches).
3/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
3.
TAPING DIMENSIONS
3.1 6N135S-TA-L/ 6N136S-TA-L
Description
3.2 6N135S-TA1-L/ 6N136S-TA1-L
Symbol
Dimension in mm (inch)
Tape wide
W
16±0.3 (0.63)
Pitch of sprocket holes
P0
4±0.1 (0.15)
F
7.5±0.1 (0.295)
Distance of compartment
Distance of compartment to compartment
P2
2±0.1 (0.079)
P1
12±0.1 (0.472)
3.3 Quantities Per Reel
Package Type
TA / TA1
Quantities (pcs)
1000
4/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
4. RATING AND CHARACTERISTICS
4.1 Absolute Maximum Ratings at Ta=25°C *1
Parameter
Symbol
Rating
Unit
Note
Average Forward Input Current
IF
25
mA
2
Reverse Input Voltage
VR
5
V
Power Dissipation
PI
45
mW
Junction temperature
TJ
125
Output Collector Current
IO
8
mA
Output Collector Voltage
VO
20
V
Output Collector Power Dissipation
Po
100
mW
Junction temperature
TJ
125
Isolation Voltage
VISO
5000
Vrms
Supply Voltage
VCC
15
V
Operating Temperature
Topr
-40 ~ +85
o
C
Storage Temperature
Tstg
-55 ~ +125
o
C
260
o
C
Input
o
C
Output
Lead Solder Temperature *2
1.
Tsol
o
C
Ambient temperature = 25oC, unless otherwise specified. Stresses exceeding the absolute maximum ratings
can cause permanent damage to the device. Exposure to absolute maximum ratings for long periods of time
can adversely affect reliability.
2.
260oC for 10 seconds.
Refer to Lead Free Reflow Profile.
5/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
4.2 ELECTRICAL OPTICAL CHARACTERISTICS at TA = 25°C
Parameters
Test Condition
Symbol
Device
Min
Typ
Max
Units
1.4
1.7
V
V
Input
Input Forward Voltage
IF =16mA, TA=25℃
VF
6N135
Input Reverse Voltage
IR = 10μA TA=25℃
BVR
6N136
5
-
-
6N135
7
18
50
6N136
19
24
50
6N135
-
0.18
0.4
Detector
IF=16mA; Vo=0.4V;
Current transfer ratio
CTR
VCC=4.5V; TA=25℃
%
IF=16mA;Vcc=4.5V;
Io=1.1mA; TA=25℃
Logic low output voltage
VOL
V
IF=16mA;Vcc=4.5V;
6N136
-
0.25
0.4
6N135
-
-
0.5
6N136
-
-
1
-
400
-
μA
-
-
1
μA
Io=3mA; TA=25℃
IF=0mA, Vo=Vcc=5.5V; TA=25℃
Logic high output current
μA
IOH
IF=0mA, Vo=Vcc=15V; TA=25℃
6N135
Logic low supply current
IF=16mA, Vo=open (Vcc=15V)
IccL
6N136
IF=0mA, Vo=open ; TA=25℃
Logic high supply current
6N135
IccH
(Vcc=15V)
6N136
* All Typical at TA =25oC
.
6/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
5. SWITCHING SPECIFICATION
Parameter
Test Condition
Symbol
Device
Min
Typ
Max
6N135
-
0.09
1.5
Units
TA=25℃
Propagation Delay Time to
(RL=4.1KΩ, IF=16mA)
Low Output Level
TA=25℃
μs
tPHL
(RL=1.9KΩ, IF=16mA)
6N136
-
0.1
0.8
6N135
-
0.8
1.5
TA=25℃
Propagation Delay Time to
(RL=4.1KΩ, IF=16mA)
High Output Level
TA=25℃
μs
tPLH
6N136
(RL=1.9KΩ, IF=16mA)
-
0.4
0.8
IF=0mA;VCM=10Vp-p;
Logic High Common Mode
RL=4.1KΩ; TA=25C
Transient Immunity
IF=0mA;VCM=10Vp-p;
6N135
|CMH|
RL=1.9KΩ; TA=25C
KV/μs
1
10
-
6N136
KV/μs
6N135
KV/μs
IF=0mA;VCM=10Vp-p;
Logic Low Common Mode
RL=4.1KΩ; TA=25C
Transient Immunity
IF=0mA;VCM=10Vp-p;
|CML|
RL=1.9KΩ; TA=25C
1
6N136
10
KV/μs
* TA=0~70℃, Vcc=5V, unless otherwise specified.
* All Typical at TA =25oC
7/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
6. ISOLATION CHARACTERISTIC
Parameter
Symbol
Min.
Typ.
Max.
Unit
II-O
—
—
1.0
μA
Withstand Insulation Test Voltage
VISO
5000
—
—
VRMS
Input-Output Resistance
RI-O
—
1012
—
Ω
Input-Output Insulation Leakage
Current
Test Condition
45% RH, t = 5s,
VI-O = 3kV DC, TA =25oC
RH ≤ 50%, t = 1min,
TA = 25oC
VI-O = 500V DC
*All Typical at TA =25oC
Notes
1. A 0.1µF or bigger bypass capacitor for VCC is needed as shown in Fig.1
2. Current Transfer Ratio is defined as the ratio of output collector current Io , to the forward LED input current IF, times 100.
3. The 1.9KΩ load represents 1TTL unit load of 1.6mA and the 5.6KΩ pull-up resistor.
4. The 4.1KΩ load represents 1LSTTL unit load of 0.36mA and the 6.1KΩ pull-up resistor.
8/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
7. SWITCHING TIME TEST CIRCUIT
Figure 1:
Test Circuit for tPHL and tPLH
Figure 2: Single Channel Test Circuit for Common Mode Transient Immunity
9/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
8. CHARACTERISTIC CURVES
Figure 3:
DC and pulsed transfer characteristics
Figure 4: Input current vs. forward voltage
Figure 5: Logic high output current vs. temperature
Figure 6: Current transfer ratio vs. input current
Figure 7: Current transfer ratio vs. temperature
Figure 8: Small-signal current transfer ratio vs.
quiescent current
10/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
Figure 9: Propagation delay time vs. temperature
Figure 10:
Propagation delay time vs. load resistance
11/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
9. TEMPERATURE PROFILE OF SOLDERING
9.1 IR Reflow soldering (JEDEC-STD-020C compliant)
One time soldering reflow is recommended within the condition of temperature and time profile shown below. Do not solder more than three
times.
Profile item
Conditions
Preheat
- Temperature Min (TSmin)
150˚C
- Temperature Max (TSmax)
200˚C
- Time (min to max) (ts)
90±30 sec
Soldering zone
- Temperature (TL)
217˚C
- Time (tL)
60 ~ 100 sec
Peak Temperature (TP)
260˚C
3˚C / sec max.
Ramp-up rate
3~6˚C / sec
Ramp-down rate
20 sec
Temperature ( C)
Ramp-up
TP 260 C
TL 217 C
Tsmax 200 C
Ramp-down
60-100 sec
Tsmin
150 C
tL (Soldering)
25 C
Time (sec)
60 ~ 120 sec
ts (Preheat)
12/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
9.2 Wave soldering (JEDEC22A111 compliant)
One time soldering is recommended within the condition of temperature.
Temperature: 260+0/-5˚C
Time: 10 sec.
Preheat temperature:25 to 140˚C
Preheat time: 30 to 80 sec.
9.3 Hand soldering by soldering iron
Allow single lead soldering in every single process. One time soldering is recommended.
Temperature: 380+0/-5˚C
Time: 3 sec max.
13/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
10. RECOMMENDED FOOT PRINT PATTERNS (MOUNT PAD)
Note :
Dimensions in millimeters.
14/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
Photocoupler
6N135-L 6N136-L series
11. NAMING RULE
6N13X (1)-(2) -L
DEVICE PART NUMBER
Classified by Electrical Characteristics
Please refer to the table on Page: P6
(1) No suffix = Dual-in-Line package
M = Wide lead spacing package
S = Surface mounting package
(2) TAPING TYPE (TA, TA1)
Please refer to orientation of taping on Page: P4
(3) Liteon P/N
Example : 6N135S-TA1-L, 6N136S-TA1-L
6N13X (1)(2)-V -L
DEVICE PART NUMBER
Classified by Electrical Characteristics
Please refer to the table on Page: P6
(1) No suffix = Dual-in-Line package
M = Wide lead spacing package
S = Surface mounting package
(2) TAPING TYPE (TA, TA1)
Please refer to orientation of taping on Page: P4
(3) VDE Option
(4) Liteon P/N
Example : 6N135STA1-V-L, 6N136STA1-V-L
12. NOTES
LiteOn is continually improving the quality, reliability, function or design and LiteOn reserves the right to make changes
without further notices.
The products shown in this publication are designed for the general use in electronic applications such as office automation
equipment, communications devices, audio/visual equipment, electrical application and instrumentation.
For equipment/devices where high reliability or safety is required, such as space applications, nuclear power control
equipment, medical equipment, etc, please contact our sales representatives.
When requiring a device for any ―specific‖ application, please contact our sales in advice.
If there are any questions about the contents of this publication, please contact us at your convenience.
The contents described herein are subject to change without prior notice.
Immerge unit’s body in solder paste is not recommended.
15/15
Part No. : 6N135-L 6N136-L series
BNS-OD-FC002/A4
工商网监
湘ICP备2023018690号
