LTDL-TA12A

L ITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only FEATURES * TTL INTERFACE COMPATIBLE * HIGH SPEED OPTIC SIGNAL TRANSMISSION * BUILT-IN LED DRIVER * BUILT-IN CURRENT LIMIT RESISTOR * LOW POWER CONSUMPTION PACKAGE DIMENSIONS V IN V DD GND 3 1 2 V DD Vin GND NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15mm(.006") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 1 of 5 L ITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ABSOLUTE MAXIMUM RATINGS AT TA=25℃ PARAMETER Supply Voltage (VDD) Input Voltage (VIN) Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] MAXIMUM RATING -0.5 ~ +7 -0.5 ~ VDD +0.5 -20 ℃ to + 70 ℃ -30 ℃ to + 80 ℃ 260℃ for 5 Seconds UNIT V V ELECTRICAL OPTICAL CHARACTERISTICS AT TA=25℃ PARAMETER Transmission Speed Operating Voltage Peak Emission Wavelength Fiber coupling light output Dissipation current High level input voltage Low level input voltage “Low High”propagation delay time “High Low”propagation delay time Pulse width distortion Viewing Angle (See FIG.2) Jitter SYMBOL MIN. Ts VDD λPeak Pc IDD VIH VIL － 2.75 630 -21 － 2 － － － -18 － － TYP. － － 650 -17 6 － － － － － 90 1 MAX. 13.2 5.25 690 -15 8 － 0.8 166 155 +18 － 18 UNIT Mbps V nm dBm mA V V hs hs hs deg. hs *3 *1 *2 TEST CONDITION NRZ signal tPLH tPHL ΔtW 2θ1/2 Δtj Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 2 of 5 L ITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only *1 Measuring method of optical output coupling power LTDL-TA12B Standard plastic optical fiber cable Optical power meter Calibrate the optical power meter to sense the light with wavelength 660nm. V IN VDD GND +- VDD 0.1uF *2 Power dissipation measuring method LTDL-TA12B V IN V DD GND 0.1uF A IDD +- VDD Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 3 of 5 L ITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only *3 Measuring pulse response LTDL-TA12B Standard plastic optical fiber cable Standard receiver Output Signal V IN V DD GND +- V DD 0.1uF Input Oscilloscope Trigger:CH1 NRZ code, 12Mbps, "1010..." pattern CH1 CH2 Input signal (CH1) 50% Standard receiver output (CH2) 50% t PLH Pulse width distortion t PHL tw = t PHL-t PLH Note (1)The impedance of the probe for the oscilloscope must be more than 1MΩ and less than 10pf. Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 4 of 5 L ITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only TYPICAL ELECTRICAL / OPTICAL CHARACTERISTICS CURVES (25℃ Ambient Temperature Unless Otherwise Noted) 1.0 Relative Radiant Intensity Relative Radiant Intensity 0 o 10 o 20 o 30 o 40 1.0 0.9 0.8 0.7 50 60 70 80 90 0.5 0.3 0.1 0.2 0.4 0.6 o o 0.5 o o o o 0 600 650 Wavelength (nm) 700 FIG.1 SPECTRAL DISTRIBUTION FIG.2 RADIATION DIAGRAM Part No. : LTDL-TA12A DATA SHEET BNS-OD-C131/A4 Page : 5 of 5