LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Lead (Pb) free product – RoHS compliant.
* High luminous intensity output.
* Low power consumption.
* High efficiency.
* Versatile mounting on P.C. Board or panel.
* I.C. Compatible/low current requirement.
* Popular T-1 diameter package.
Package
Dimensions
Part No.
LTL17KTGX3KS-032A
Lens
Source Color
Green Diffused
InGaN Green
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Absolute Maximum Ratings at TA=25°C
Parameter
Maximum Rating
Unit
105
mW
100
mA
Continuous Forward Current
30
mA
Derating Linear From 50°C
0.43
mA/°C
Operating Temperature Range
-30°C to + 85°C
Storage Temperature Range
-40°C to + 100°C
Power Dissipation
Peak Forward Current
(1/10 Duty Cycle, 0.1ms Pulse Width)
Lead Soldering Temperature
[2 mm(.078") From Body]
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
260°C for 5 Seconds Max.
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25°C
Parameter
Symbol
Min.
Typ.
Max.
Unit
IV
7200
19000
-
mcd
2θ1/2
-
30
-
deg
Peak Emission Wavelength
λP
-
526
-
nm
Dominant Wavelength
λd
524
-
536
nm
Spectral Line Half-Width
∆λ
-
35
-
nm
Forward Voltage
VF
2.75
-
3.5
V
IF = 20mA
Reverse Current
IR
-
-
100
µA
VR = 5V, Note 6
Luminous Intensity
Viewing Angle
Test Condition
IF = 20mA
Note 1
Note 2 (Fig.5)
Measurement
@Peak (Fig.1)
Note 4
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
eye-response curve.
2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
3. Iv classification code is marked on each packing bag.
4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the
single wavelength which defines the color of the device.
5. The Iv guarantee should be added ±15%.
6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for
reverse operation.
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics
(25°C Ambient
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Temperature
Unless
Otherwise
Curves
Noted)
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 2.54mm (0.1") straight lead spacing available.
* Folding packaging simplifies handling and testing.
Reel packaging is available by removing suffix “A” on option.
Package Dimensions
Item
Tape Feed Hole Diameter
Component Lead Pitch
Front to Rear Deflection
Feed Hole to Bottom of Component
Feed Hole to Overall Component Height
Lead Length After Component Height
Feed Hole Pitch
Lead Location
Center of Component Location
Total Tape Thickness
Feed Hole Location
Adhesive Tape Position
Tape Width
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Symbol
D
F
∆H
H1
H2
L
P
P1
P2
T
W0
W2
W3
Specification
Minimum
Maximum
mm
inch
mm
inch
3.8
0.149
4.2
0.165
2.3
0.091
3.0
0.118
--2.0
0.079
20.0
0.787
21.0
0.827
25.6
1.007
27.2
1.071
W0
11.0
0.433
12.4
0.488
13.0
0.511
4.4
0.173
5.8
0.228
5.05
0.199
7.65
0.301
--0.90
0.035
8.5
0.334
9.75
0.384
0
0
3.0
0.118
17.5
0.689
19.0
0.748
Page :
5
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Packing Spec
2000 pcs per inner carton
10 Inner cartons per outer carton
total 20000 pcs per outer carton
In every shipping lot, only the last pack will be non-full packing
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
6
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Bin Table Specification
Luminous Intensity
Unit : mcd @20mA
Bin Code
Min.
Max.
X
7200
9300
Y
9300
12000
Z
12000
16000
1
16000
21000
Note: Tolerance of each bin limit is ±15%
Hue Spec. Table Specification.
Dominant Wavelength λd(nm) IF@20mA
Bin Code
Min.
Max.
G11
524
528
G12
528
532
G13
532
536
Note: Tolerance of each bin limit is ± 1 nm
Part
No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
4. Lead Forming & Assembly
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done
before soldering, at normal temperature. During assembly on PCB, use minimum clinch force
possible to avoid excessive mechanical stress.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point.
Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame
during soldering while the LED is at high temperature.
Recommended soldering conditions :
Soldering iron
Temperature
Soldering time
350°C Max.
3 sec. Max.
(one time only)
Wave soldering
Pre-heat
Pre-heat time
Solder wave
Soldering time
100°C Max.
60 sec. Max.
260°C Max.
5 sec. Max.
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
catastrophic failure of the LED.IR reflow is not suitable process for through hole type LED lamp product.
Part No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
6. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs
connected in parallel in an application, it is recommended that a current limiting resistor be
incorporated in the drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
LED
Circuit model B
LED
(A) Recommended circuit
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs
7. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
Use a conductive wrist band or anti- electrostatic glove when handling these LEDs
All devices, equipment, and machinery must be properly grounded
Work tables, storage racks, etc. should be properly grounded
Use ion blower to neutralize the static charge which might have built up on surface of the LEDs
plastic lens as a result of friction between LEDs during storage and handing
Part No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Suggested checking list :
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTL17KTGX3KS-032A
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
8. Reliability Test
Classification
Test
Item
Operation Life
Test
Condition
Ta
= 25°C
45 PCS
IF
= 30mA
(CL=90%;
LTPD=5%)
*Test Time= 1000hrs
High Temperature/
Endurance
Test
Ta
RH = 85%
Steady state
Ta
Operation Life of
IF
High Humidity Heat
*Test Time= 500hrs
Low Temperature
Operation Life
Ta
*Test Time= 500hrs
= 85°C, RH= 85 %
= 10mA
= -30°C,
IF
MIL-STD-750D:1026 (1995)
MIL-STD-883G:1005 (2006)
MIL-STD-202G:103B (2002)
(CL=90%;
LTPD=5%)
(CL=90%;
LTPD=3%)
= 30mA
JEITA ED-4701:100 103 (2001)
JESD22-A101C (2009)
45 PCS
(CL=90%;
LTPD=5%)
Ta= 105 ± 5°C
*Test Time= 1000hrs
45 PCS
MIL-STD-750D:1031 (1995)
(CL=90%;
LTPD=5%)
MIL-STD-883G:1008 (2006)
JEITA ED-4701:200 201 (2001)
45 PCS
Low Temperature
Ta= -55 ± 5°C
Storage
*Test Time= 1000hrs
(CL=90%;
LTPD=5%)
100°C ~ 25°C ~ -40°C ~ 25°C
76 PCS
30mins
(CL=90%;
LTPD=3%)
Cycling
Standard
76 PCS
*Test Time= 1000hrs
Temperature
Reference
45 PCS
= 85°C
High Humidity storage
(THB)
High Temperature
Storage
Sample Size
5mins
30mins
5mins
*Test time: 200 Cycles
JEITA ED-4701:200 202 (2001)
MIL-STD-750D:1051 (1995)
MIL-STD-883G:1010 (2006)
JEITA ED-4701:100 105 (2001)
JESD22-A104C (2005)
100 ± 5°C ~ -30°C ± 5°C
Thermal
Shock
15mins
~
15mins
*Test time: 200 Cycles
MIL-STD-750D:1056 (1995)
76 PCS
MIL-STD-883G:1011 (2006)
(CL=90%;
LTPD=3%)
(
很抱歉,暂时无法提供与“LTL17KTGX3KS”相匹配的价格&库存,您可以联系我们找货
免费人工找货