LTL2R3FU3JSR

Through Hole Lamp Product Data Sheet LTL2R3FU3JSR Spec No. :DS20-2011-0152 Effective Date: 04/22/2020 Revision: B LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto Through-Hole Lamp LTL2R3FU3JSR Through Hole Lamp LTL2R3FU3JSR Rev Description By Date Above data for PD and Customer tracking only - NPPR Received and Upload on OPNC Nedphakas 08/25/2011 A Update new IV bin table (IV = P/Q/R/S) Nedphakas 09/14/2012 B Update new IV bin table (IV = P/Q/R) Apisit 04/14/2020 1/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 1. Description 5mm round lamp is a popular design with a smooth uniform view angle radiation pattern suitable in Full color signboard, Billboard sign, Message sign and bus sign. High luminous intensity output has a higher emitting efficiency to save power energy. Advanced epoxy technology has a good moisture resistance and UV protection to be used in package, and it can reduce the effect of long term exposure in outdoor environment. 1. 1. Features        High Luminous intensity output. Low power consumption & High efficiency. Superior resistance to moisture Good UV inhibitor Lead free & RoHS Compliant Popular T-1 3/4diameter, Amber AlGaInP 607nm Lamp, White Diffused package. Typical viewing angle 30°. 1.2. Applications     Video message sign Traffic sign Message sign Bus sign 2. Outline Dimensions Notes: 1. 2. 3. 4. All dimensions are in millimeters (inches). Tolerance is ±0.25mm (.010") unless otherwise noted. Protruded resin under flange is 1.0mm (.04") max. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. 2/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 3. Absolute Maximum Ratings at TA=25℃ ℃ Parameter Maximum Rating Unit 120 mW 90 mA DC Forward Current 50 mA Derating Linear From 25℃ 0.5 mA/℃ 5 V Power Dissipation Peak Forward Current (Duty Cycle≦1/10, Pulse Width≦0.1ms) Reverse Voltage Operating Temperature Range -40°C to + 85°C Storage Temperature Range -55°C to + 100°C Lead Soldering Temperature 260°C for 5 Seconds Max. [2.0mm (.079") From Body] 4. Electrical / Optical Characteristics at TA=25℃ ℃ Parameter Symbol Min. IV 880 2θ1/2 25 Typ. Max. Unit 1900 mcd Test Condition IF = 10mA Luminous Intensity Note 1,5 IF = 10mA Viewing Angle Peak Emission Wavelength λP Dominant Wavelength λd Spectral Line Half-Width Δλ Forward Voltage VF Reverse Current IR 30 deg 607 nm Note 2 (Fig.6) IF = 10mA Measurement @Peak (Fig.1) IF = 10mA 600 604 610 1.9 Note 4 nm IF = 10mA 2.4 V IF = 10mA 100 μA VR = 5V 17 1.7 nm NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 5. Iv guarantee must be included with ±15% testing tolerance. 6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation. 3/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 5. Typical Electrical / Optical Characteristics Curves (25℃ Ambient Temperature Unless Otherwise Noted) 4/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 6. Packing Spec. 1000, 500 or 250 pcs per packing bag 8 packing bags per inner carton, Total 8,000 pcs per inner carton 8 Inner cartons per outer carton, Total 64,000 pcs per outer carton. In every shipping lot, only the last pack will be non-full packing. 5/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 7. Bin Table Specification Luminous Intensity Iv (mcd) IF@10mA Bin Code Min. Max. P 880 1150 Q 1150 1500 R 1500 1900 Note: Tolerance of each bin limit is ±15% Dominant Wavelength λd (nm)@10mA Bin Code Min Max H23 600.0 603.0 H24 603.0 606.5 H25 606.5 610.0 Note: Tolerance of each bin limit is ±1nm Forward Voltage Vf Unit : V @10mA Bin Code Min Max 0 1.7 1.8 1 1.8 1.9 2 1.9 2.0 3 2.0 2.1 4 2.1 2.2 5 2.2 2.3 6 2.3 2.4 Note: Tolerance of each bin limit is ±0.05V 6/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 8. CAUTIONS 9.1. Application This LED lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 9.2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is re commended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 9.3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 9.4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 9.5. Soldering When soldering, leave a minimum of 3mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions: Soldering iron Temperature Soldering time Position 350°C Max. 3 seconds Max. (one time only) No closer than 2mm from the base of the epoxy bulb Wave soldering Pre-heat Pre-heat time Solder wave Soldering time Dipping Position 100°C Max. 60 seconds Max. 260°C Max. 5 seconds Max. No lower than 2mm from the base of the epoxy bulb Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. 9.6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model (A) LED Circuit model (B) LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 7/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 9.7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:     Use a conductive wrist band or anti- electrostatic glove when handling these LEDs All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Suggested checking list: Training and Certification 9.7.1.1. Everyone working in a static-safe area is ESD-certified? 9.7.1.2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 9.7.2.1. Static-safe workstation or work-areas have ESD signs? 9.7.2.2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 9.7.2.3. All ionizer activated, positioned towards the units? 9.7.2.4. Each work surface mats grounding is good? Personnel Grounding 9.7.3.1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 9.7.3.1. If conductive footwear used, conductive flooring also present where operator stand or walk? 9.7.3.2. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 9.7.3.3. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 9.7.3.4. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 9.7.4.1. Every ESDS items identified by EIA-471 labels on item or packaging? 9.7.4.2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 9.7.4.3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 9.7.4.4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 9.7.5.1. Audit result reported to entity ESD control coordinator? 9.7.5.2. Corrective action from previous audits completed? 9.7.5.3. Are audit records complete and on file? 8/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4 Through-Hole Lamp LTL2R3FU3JSR 9. Reliability Test Classification Endurance Test Environmental Test Test Item Test Condition Sample Size Reference Standard Operation Life Ta = 25°C IF = 30mA Test Time = 1000hrs 45 PCS (CL=90%; LTPD=5%) MIL-STD-750D:1026 (1995) MIL-STD-883G:1005 (2006) High Temperature High Humidity storage (THB) Ta = 85°C RH = 85% Test Time = 1000hrs 45 PCS (CL=90%; LTPD=5%) MIL-STD-202G:103B (2002) JEITA ED-4701:100 103 (2001) Steady state Operation Life of High Humidity Heat Ta = 85°C, RH= 85 % IF = 5mA Test Time = 500hrs 76 PCS (CL=90%; LTPD=3%) JESD22-A101C (2009) Low Temperature Operation Life of Ta = -30°C IF = 20A Test Time = 1000hrs 45 PCS (CL=90%; LTPD=5%) High Temperature Storage Ta = 105 ± 5°C Test Time = 1000hrs 45 PCS (CL=90%; LTPD=5%) MIL-STD-750D:1031 (1995) MIL-STD-883G:1008 (2006) JEITA ED-4701:200 201 (2001) Low Temperature Storage Ta = -55 ± 5°C Test Time = 1000hrs 45 PCS (CL=90%; LTPD=5%) JEITA ED-4701:200 202 (2001) Temperature Cycling 100°C ～ 25°C ～ -40°C ～ 25°C 30mins 5mins 30mins 5mins Test time: 200 Cycles 76 PCS (CL=90%; LTPD=3%) MIL-STD-750D:1051 (1995) MIL-STD-883G:1010 (2006) JEITA ED-4701:100 105 (2001) JESD22-A104C (2005) Thermal Shock 100 ± 5°C ～ -30°C ± 5°C 15mins 15mins Test time: 200 Cycles 76 PCS (CL=90%; LTPD=3%) MIL-STD-750D:1056 (1995) MIL-STD-883G:1011 (2006) MIL-STD-202G:107G (2002) JESD22-A106B (2004) Solder Resistance T. sol = 260 ± 5°C Dwell Time= 10±1 seconds 3mm from the base of the epoxy bulb 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-750D:2031(1995) JEITA ED-4701: 300 302 (2001) Solderability T. sol = 245 ± 5°C Dwell Time= 5 ± 0.5 seconds (Lead Free Solder, Coverage ≧95% of the dipped surface) 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-750D:2026 (1995) MIL-STD-883G:2003 (2006) MIL-STD-202G:208H (2002) IPC/EIA J-STD-002 (2004) Soldering Iron T. sol = 350 ± 5°C Dwell Time= 3.5 ± 0.5 seconds 11 PCS (CL=90%; LTPD=18.9%) MIL-STD-202G:208H (2002) JEITA ED-4701:300 302 (2001) 10. Others The appearance and specifications of the product may be modified for improvement, without prior notice. 9/9 Part No.: LTL2R3FU3JSR BNS-OD-FC002/A4