LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
LED DISPLAY
LTP-3363CKR-P
DATA SHEET
ITEM
1
Description
New Spec
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
By
Reo Lin
PAGE:
DATE
2011/07/15
1 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
FEATURES
*0.3 inch (7.62 mm) DIGIT HEIGHT
*CONTINUOUS UNIFORM SEGMENTS
*LOW POWER REQUIREMENT
*EXCELLENT CHARACTERS APPEARANCE
*HIGH BRIGHTNESS & HIGH CONTRAST
*WIDE VIEWING ANGLE
*SOLID STATE RELIABILITY
*CATEGORIZED FOR LUMINOUS INTENSITY
*SMD DISPLAY
*LEAD-FREE PACKAGE (ACCORDING TO RoHS)
DESCRIPTION
The LTP-3363CKR-P is a 0.3 inch (7.62 mm) digit height dual digit 17-segment
alphanumeric display. This device uses AS-AlInGaP SUPER RED LED chips
(AlInGaP epi on GaAs substrate). The display has black face and white segments.
DEVICE
PART NO.
DESCRIPTION
AllnGaP RED
Multiplex Common Cathode
LTP-3363CKR-P
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
Rt. Hand Decimal
PAGE:
2 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
PACKAGE DIMENSIONS
NOTES: 1.All dimensions are in millimeters. Tolerances are ± 0.25mm (0.01“) unless otherwise noted.
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
3 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
INTERNAL CIRCUIT DIAGRAM
PIN CONNECTION
No.
CONNECTION
1
ANODE F
2
ANODE T
3
ANODE S
4
COMMON CATHODE (Digit 1)
5
ANODE DP
6
ANODE G
7
ANODE R
8
ANODE D
9
ANODE E
10
COMMON CATHODE (Digit 2)
11
ANODE B
12
ANODE N
13
ANODE A
14
NO CONNECTION
15
ANODE H
16
ANODE P
17
ANODE C
18
ANODE M
19
ANODE K
20
ANODE U
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
4 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
ABSOLUTE MAXIMUM RATING
PARAMETER
MAXIMUM RATING
UNIT
Power Dissipation Per Segment
70
mW
Peak Forward Current Per Segment
( Frequency 1Khz, 18% duty cycle)
90
mA
Continuous Forward Current Per Segment
0
Forward Current Derating from 25 C
25
0.27
-350C to +1050C
Operating Temperature Range
mA
0
mA/ C
-350C to +1050C
Storage Temperature Range
Soldering Conditions : 1/16 inch below seating plane for 3 seconds at 2600C
ELECTRICAL / OPTICAL CHARACTERISTICS
PARAMETER
SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION
Average Luminous Intensity
Per Segment
IV
Peak Emission Wavelength
λp
639
nm
IF=20mA
Spectral Line Half-Width
∆λ
20
nm
IF=20mA
Dominant Wavelength
λd
631
nm
IF=20mA
Forward Voltage Per Segment
VF
2.0
2.6
V
IF=20mA
Reverse Current Per Segment
IR
100
µA
VR=5V
IV-m
2:1
Luminous Intensity Matching Ratio
T.B.D
T.B.D
µcd
T.B.D
IF=1mA
IF=10mA
IF=1mA
Note: Luminous intensity is measured with a light sensor and filter combination that
approximates the CIE (Commision Internationale De L’Eclairage) eye-response curve.
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
5 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
TYPICAL ELECTRICAL / OPTICAL CHARACTERISTIC CURVES
(25oC Ambient Temperature Unless Otherwise Noted)
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
6 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
SMT SOLDERING INSTRUCTION
(Number of reflow process shall be less than 2 times, and cooling process to normal temperature is
required between the first and the second soldering process)
Note:
1. Recommended soldering condition:
Reflow Soldering (Two times only)
Pre-heat:
120~150°C.
Pre-heat time:
120sec. Max.
Peak temperature:
260°C Max.
Soldering time:
5sec. Max.
Soldering Iron (One time only)
Temperature
300°C Max.
Soldering time
3sec. Max.
2. Number of reflow process shall be less than 2 times, and cooling process to normal temperature is
required between the first and the second soldering process.
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
7 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
RECOMMENDED SOLDERING PATTERN (UNIT: mm)
PACKING MODE
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
8 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
PACKING REEL DIMENSIONS
NOTE : packing qty 950 PCS/REEL
32+/-0.30
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
9 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Moisture Proof Packaging
All N/D SMD displays are shipped in moisture proof package. The displays should be stored at 30°C or
less and 90% RH or less. Once the package opened, moisture absorption begins.
UNITS IN A SEALED
MOISTURE-PROOF
PACKAGE
PACKAGE IS
OPENED (UNSEALED)
YES
ENVIRONMENT LESS
THAN 30oC, AND
LESS THAN 60% RH?
BAKING IS NOT
NECESSARY
NO
NO
PACKAGE IS
OPENED MORE
THAN 1 WEEK
DAYS?
YES
PERFORM
RECOMMENDED
BAKING CONDITIONS
Baking Conditions
If the parts are not stored in dry conditions, they must be baked before reflow to prevent damage to the
parts.
Package
Temperature
Time
In Reel
60oC
≧48hours
In Bulk
100oC
≧4hours
o
125 C
≧2hours
Baking should only be done once.
PART NO.: LTP-3363CKR-P
BNS-OD-C131/A4
PAGE:
10 of 10
很抱歉,暂时无法提供与“LTP-3363CKR-P”相匹配的价格&库存,您可以联系我们找货
免费人工找货