LTST-E670FL

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * * * * * * Package in 8mm tape on 7" diameter reels. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. EIA STD package. I.C. compatible. Lead-Free package (According to RoHS). Package Dimensions Part No. Lens Color Source Color LTST-E670FL Water Clear AlInGaP Orange Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2 mm (.008") unless otherwise noted. Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 1 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ℃ Absolute Maximum Ratings at Ta=25℃ Parameter LTST-E670FL Unit Power Dissipation 180 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) 100 mA DC Forward Current 70 mA 1.27 mA/℃ Reverse Voltage 12 V Operating Temperature Range -55℃ to + 80℃ Storage Temperature Range -55℃ to + 80℃ Derating Linear From 65℃ Suggest IR Reflow Condition : IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B) Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 2 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ℃ Electrical / Optical Characteristics at Ta=25℃ Parameter Symbol Luminous Intensity Part No. LTST- Min. Typ. 710.0 Max. Unit Test Condition 2800.0 mcd IF = 50mA Note 1 IV E670FL Viewing Angle 2θ1/2 E670FL 120 deg Note 2 (Fig.6) Peak Emission Wavelength λP E670FL 611 nm Measurement @Peak (Fig.1) Dominant Wavelength λd E670FL nm Note 3 Spectral Line Half-Width ∆λ E670FL 20 Forward Voltage VF E670FL 2.1 Reverse Current IR E670FL Capacitance C E670FL 600 609 40 nm 2.8 V IF = 50mA 100 μA VR = 5V PF VF=0, f =1MHZ NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Forward Voltage Tolerance is +/- 0.1 volt. Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 3 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List Luminous Intensity Unit : mcd @50mA Bin Code Min. Max. V1 710.0 900.0 V2 900.0 1120.0 W1 1120.0 1400.0 W2 1400.0 1800.0 X1 1800.0 2240.0 X2 2240.0 2800.0 Tolerance on each Intensity bin is +/-15% Dominant Wavelength Unit : nm @50mA Bin Code Min. Max. P 600.0 603.0 Q 603.0 606.0 R 606.0 609.0 Tolerance for each Dominant Wavelength bin is +/-1nm Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 4 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25°° C Ambient Temperature Unless Otherwise Noted) Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 5 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only User Guide Cleaning Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less one minute. Recommend Printed Circuit Board Attachment Pad Infrared / vapor phase Reflow Soldering Package Dimensions Of Tape And Reel Note: 1.All dimensions are in millimeters (inches). Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 6 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Package Dimensions of Reel Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-2000 pieces per reel. 3. Minimum packing quantity is 500 pieces for remainders. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with EIA-481-1-B specifications. Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 7 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 85°C temperature or 60% relative humidity. It is recommended that LEDs out of their original packaging are IR-reflowed within one week. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant, or in desiccators with nitrogen ambient. LEDs stored out of their original packaging for more than a week should be baked at about 60 °C for at least 24 hours before solder assembly. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Wave Soldering Pre-heat Pre-heat time Soldering Temp. Soldering time 120~150°C 120 sec. Max. 260°C Max. 30 sec. Max. Pre-heat Pre-heat time Solder wave Soldering time Soldering iron 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Temperature Soldering time 300°C Max. 3 sec. Max. (one time only) 5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:



Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED’s plastic lens as a result of friction between LEDs during storage and handling. Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 8 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or “no lightup” at low currents. To verify for ESD damage, check for “lightup” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. 7. Reliability Test Classification Test Item Reference Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS, +72HRS)*@50mA. MIL-STD-750D:1026 MIL-STD-883D:1005 JIS C 7021:B-1 High Temperature High Humidity Storage IR-Reflow In-Board, 2 Times Ta= 65±5℃,RH= 90～95% *Test Time= 240HRS±2HRS MIL-STD-202F:103B JIS C 7021:B-11 High Temperature Storage Ta= 105±5℃ *Test Time= 1000HRS (-24HRS,+72HRS) MIL-STD-883D:1008 JIS C 7021:B-10 Low Temperature Storage Ta= -55±5℃ *Test Time=1000HRS (-24HRS,+72H RS) JIS C 7021:B-12 105℃ ～ 25℃ ～ -55℃ ～ 25℃ 30mins 5mins 30mins 5mins 10 Cycles MIL-STD-202F:107D MIL-STD-750D:1051 MIL-STD-883D:1010 JIS C 7021:A-4 IR-Reflow In-Board, 2 Times 85 ± 5℃ ～ -40℃ ± 5℃ 10mins 10mins 100 Cycles MIL-STD-202F:107D MIL-STD-750D:1051 MIL-STD-883D:1011 Ramp-up rate(217℃ to Peak) +3℃/ second max Temp. maintain at 175(±25)℃ 180 seconds max Temp. maintain above 217℃ 60-150 seconds Peak temperature range 260℃+0/-5℃ Time within 5°C of actual Peak Temperature (tp) 20-40 seconds Ramp-down rate +6℃/second max MIL-STD-750D:2031.2 J-STD-020B T.sol= 235 ± 5℃ Immersion time 2±0.5 sec Immersion rate 25±2.5 mm/sec Immersion rate 25±2.5 mm/sec Coverage ≧95% of the dipped surface MIL-STD-202F:208D MIL-STD-750D:2026 MIL-STD-883D:2003 IEC 68 Part 2-20 JIS C 7021:A-2 Operation Life Endurance Test Test Condition Temperature Cycling Thermal Shock Environmental Test IR-Reflow Solderability 8. Others The appearance and specifications of the product may be modified for improvement without prior notice. 9. Quality Guarantee LiteOn guarantee DPPM level of function failure is smaller and equal to 50 DPPM. (Based on 100k usage) Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 9 of 10 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 10. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTST-E670FL BNS-OD-C131/A4 Page : 10 of 10