PA-1360-5M00

規 格 書 Electrical Specification Model No： ： PA-1360-5M01 Description： ： 12V 36W single output AC adapter Revision： ： A Issued Date： ： May 21, 2013 Customer Part No.： ： 90, Chien I Rd, Chung Ho city, Taipei Hsien 235, Taiwan Tel : 886-2-2222-6181 Fax : 886-2-2226-1922 Approve By Check By Koson Lu Tom Hsu Prepared By Sammi Pan ELECTRICAL SPECIFICATION Change List ECN No REV Revision Description Date A Initial 5/21/2013 Model No：PA-1360-5M01 Page： 2 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION Contents 1. Description ....................................................................................................................... 4 2. Electrical ........................................................................................................................... 4 2.1 Input Voltage (AC ~). ................................................................................................... 4 2.2 Input Frequency............................................................................................................ 4 2.3 Input Current ................................................................................................................ 4 2.4 Inrush Current .............................................................................................................. 4 2.5 Hold-Up time (main interruption requirement)............................................................ 4 2.6 Efficiency...................................................................................................................... 4 2.7 Safety Test .................................................................................................................... 4 2.8 Start Up......................................................................................................................... 4 2.9 No load power consumption ........................................................................................ 4 2.10 Rise Time.................................................................................................................... 4 2.11 Over-Shoot and under-shoot....................................................................................... 5 2.12 DC output requirement............................................................................................... 5 2.13 Output circuit protection. ........................................................................................... 5 2.14 Transient Response..................................................................................................... 5 3. Environment ..................................................................................................................... 5 3.1 Temperature.................................................................................................................. 5 3.2 Humidity....................................................................................................................... 6 4. Safety / EMC ..................................................................................................................... 6 4.1 Safety. ........................................................................................................................... 6 4.2 EMS.............................................................................................................................. 6 4.3 EMI for both Conduction & Radiation. ....................................................................... 6 5. Reliability .......................................................................................................................... 6 5.1 Lifetime. ....................................................................................................................... 6 5.2 Burn-in ......................................................................................................................... 7 5.3 Vibration Test ............................................................................................................... 7 5.4 M.T.B.F ........................................................................................................................ 7 6. Mechanical ....................................................................................................................... 7 6.1 Physical Size ................................................................................................................ 7 6.2 Input connector............................................................................................................. 7 6.3 Output connector. ......................................................................................................... 7 6.4 Outline Drawing. .......................................................................................................... 8 Model No：PA-1360-5M01 Page： 3 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION 1. Description This product is an external AC to DC adapter power transfer device; it is able to provide 12V 36W single dc output with constant voltage source. 2. Electrical 2.1 Input Voltage (AC ~). a. From 100-240 Vac Nominal. b. From 90-264 Vac Maximum. 2.2 Input Frequency From 47-63Hz Maximum. 2.3 Input Current 1.0A max at 100Vac and dc output max load. 2.4 Inrush Current 50A maximum at cold-start & 25℃ & DC output at full-load and 125Vac input. 2.5 Hold-Up time (main interruption requirement) 16.67 msec minimum at full-load and 110Vac/60Hz AC input. 2.6 Efficiency. Average 25/50/75/100% load power efficiency need to >= 84.6% at 115Vac and 230Vac. Test condition will be tested after full load operating for 30min then measure it. 2.7 Safety Test a. Leakage current less then 0.25mA at 254Vac, 50Hz. b. Hi-pot test: 3000Vac, 10mA, 3sec between Primary to Secondary. c. Insulation: 500Vdc, 2Sec between Primary to Secondary circuit, IR shall≧20MΩ. 2.8 Start Up. The output voltage shall rise from 0 volt and settle within regulation in less than 2sec, from apply of 115Vac. 2.9 No load power consumption AC input power Pin shall be less than 0.3W at no load and 230Vac/50hz condition. 2.10 Rise Time. That shall be less than 20msec from 10% to 90% of dc output voltage. Model No：PA-1360-5M01 Page： 4 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION 2.11 Over-Shoot and under-shoot. Less than 10% of nominal DC output voltage. 2.12 DC output requirement. Vout Vout min Vout typ Vout max Ripple/noise Iout max Iout min +12V 11.4V 12.0V 12.6V 120 3000 0 Remark Vdc Vdc Vdc mVpp mA mA Ripple and Noise. Tested by dc loading side parallel with a 10uF/25V aluminum electrolytic & 0.1uF/50V Ceramic capacitor and Measured Band-Width with 20MHz. 2.13 Output circuit protection. a. SCP: short circuited protection with auto-recovery function. b. OCP: Over current protection shall be less than 4.5A with auto-recovery function c. OVP: Over voltage protection with auto-recovery function. Tripped voltage will be less than 18Vmax. 2.14 Transient Response. Dynamic load condition. Vin (AC) DC output Vout Max 115Vac/230Vac 12V 12.6 Vout Min I1(A) I2(A) 0 1.50 1.50 3.00 11.4 I1 time I2 time dI/dT 0.5msec 0.5msec 0.1A/usec 3. Environment 3.1 Temperature a. Operation: 0 to 50 ℃ for nominal input condition. b. Storage: -20 to 70 ℃ Model No：PA-1360-5M01 Page： 5 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION 3.2 Humidity a. Operation: 5-90% for nominal input condition. b. Storage: 5-95%. 4. Safety / EMC 4.1 Safety. Safety referring Standards UL/C-UL UL 60065 7th edition , 60950-1 2nd 4.2 EMS. Test Item Test Specification. IEC standards ESD Contact +/- 8KV 61000-4-2 ESD Air +/- 15KV 61000-4-2 EFT 2KV on AC power line. 61000-4-4 Bi-wave +/- 6KV / 2ohm 3000A, SURGE Ring wave +/- 6KV / 12ohm 500A 61000-4-5 on both differential and common mode. CS 3V/M 61000-4-6 RS Fr: 80MHz-3.0GHz, Field Strength : 3V/M 61000-4-3 DIPS 0% 250Cy, 40% 5Cy, 70% 0.5Cycle 61000-4-11 4.3 EMI for both Conduction & Radiation. Referring Standards Spec / Certified FCC Part 15,class B CISPR CISPR 22, class B 5. Reliability 5.1 Lifetime. 61320 hours (7 years) at 27W load 115Vac , ambient temperature 50℃. Model No：PA-1360-5M01 Page： 6 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION 5.2 Burn-in 100% Burn-In with 80-100% loading & 30-40℃ Environment temperature. 5.3 Vibration Test a. Non operation vibration with shipping container shall be 2G'S peak, 7-250Hz, 1G'S peak 50-500Hz, after 30 minute test no abnormally to be found. b. Operation vibration shall be 0.5G'S peak, 5-250Hz, 3 planes, after 30 minute test no abnormally to be noted. 5.4 M.T.B.F Prediction: Minimum 200,000 hours @ 25 °C, full load, 115Vac/230Vac, SR-332 6. Mechanical 6.1 Physical Size Plastic case size 126.5mm ( L ) X 50mm ( W ) X 30.6mm ( H ) 6.2 Input connector IEC 60320/C8 Type. 6.3 Output connector. Dc output with traditional barrel type 5.5 x 2.1 x 10.5mm, 1.83M, UL1185 18AWG cable. Model No：PA-1360-5M01 Page： 7 Revision：A Date：5.21.2013 ELECTRICAL SPECIFICATION 6.4 Outline Drawing. Model No：PA-1360-5M01 Page： 8 Revision：A Date：5.21.2013