PB-1240-6SA0

Specification Model No： PB-1240-6SA1 Description： 12V 24W AC Adapter Revision： Issued Date： A 2013/05/21 Customer Part No.： 90, Chien I Rd, Chung Ho city, Taipei Hsien 235, Taiwan Tel : 886-2-2222-6181 Fax : 886-2-2226-1922 Approve By Koson Lu Check By Tom Hsu Prepared By Steven Yeh SPECIFICATION Change List ECN No REV Revision Description Date A Initial 2013/05/21 Model No：PB-1240-6SA1 Page： 2 Revision：07 Date：05.21.2013 SPECIFICATION Contents Specification .................................................................................................................1 1. Description ...................................................................................................................5 2. Electrical .......................................................................................................................5 2.1 Input Voltage (AC ~) .................................................................................................5 2.2 Input Frequency ........................................................................................................5 2.3 Input Current.............................................................................................................5 2.4 Inrush Current ...........................................................................................................5 2.5 Hold-Up time ............................................................................................................5 2.6 Efficiency .................................................................................................................5 2.7 Safety Test ................................................................................................................5 2.8 Start Up.....................................................................................................................5 2.9 No load power consumption ......................................................................................5 2.10 Rise Time ................................................................................................................6 2.11 Over-Shoot and under-shoot ....................................................................................6 2.12 DC output requirement ............................................................................................6 2.14 Output circuit protection .........................................................................................6 2.15 Transient Response .................................................................................................6 3. Environment .................................................................................................................6 3.1 Temperature ..............................................................................................................6 3.2 Humidity...................................................................................................................6 4. Safety / EMC .................................................................................................................7 4.1 Safety........................................................................................................................7 4.2 EMS .........................................................................................................................7 4.3 EMI for both Conduction & Radiation ......................................................................9 5. Reliability ......................................................................................................................9 5.1 Aluminum Capacitor Lifetime ...................................................................................9 5.2 Burn-in .....................................................................................................................9 5.3 Vibration Test ............................................................................................................9 5.4 M.T.B.F ....................................................................................................................9 5.5 Acoustic ....................................................................................................................9 6. Mechanical ................................................................................................................. 10 6.1 Physical Size ...........................................................................................................10 6.2 Input connector ....................................................................................................... 10 6.3 Output connector..................................................................................................... 10 Model No：PB-1240-6SA1 Page： 3 Revision：07 Date：05.21.2013 SPECIFICATION 6.4 Weight about ...........................................................................................................10 6.4 Flammability ...........................................................................................................10 Model No：PB-1240-6SA1 Page： 4 Revision：07 Date：05.21.2013 SPECIFICATION 1. Description This product is an adapter type AC to DC power transfer device; it is able to provide 24W single dc output with constant voltage source. 2. Electrical 2.1 Input Voltage (AC ~) a. From 100-120 Vac Nominal. b. From 90-132 Vac Maximum. 2.2 Input Frequency a. 50/60 Hz Nominal. b. From 47-63 Hz Maximum. 2.3 Input Current 0.6A max at 90Vac and dc output max load. 2.4 Inrush Current 60A max. at DC output at Full-load and 132Vac/60Hz input for Cold Start at 25℃, AC input voltage’s phase angle is 90±10° degrees. 2.5 Hold-Up time (main interruption requirement) 16.7 ms minimum at full-load at 90Vac 60Hz AC input. 2.6 Efficiency Average 25/50/75/100% load power efficiency need to >= 82.5% at 115Vac to compliance with CEC level V efficiency requirement. Test condition will be tested after full load operating for 30min then measure it. 2.7 Safety Test a. Leakage current less then 0.25mA. b. Hi-pot test: 3000Vac 5mA, 1 minus between Primary to Secondary. c. Insulation: 500Vdc, 2Sec between Primary to Secondary circuit, IR shall≧20MΩ. 2.8 Start Up The output voltage shall rise from 0 volt and settle within regulation in less then 2sec, from apply of 115Vac. 2.9 No load power consumption AC input power Pin shall be less then 0.3W at no load and 115Vac, 60Hz condition. Model No：PB-1240-6SA1 Page： 5 Revision：07 Date：05.21.2013 SPECIFICATION 2.10 Rise Time From 10% to 90% of dc output voltage shall be less then 50msec with the 1000uF capacitive load to that of the product. 2.11 Over-Shoot and under-shoot Less than 5% of nominal AC input voltage. 2.12 DC output requirement Vout Vout min Vout typ Vout max Ripple/noise Iout max Iout min +12V 11.4V 12.0V 12.6V 120 2 0 Remark Vdc Vdc Vdc mVpp A A Ripple and Noise. Tested by dc loading side parallel with a 22uF/EC and 0.1uF/Ceramic capacitor and Measured Band-Width with DC-20MHz. 2.14 Output circuit protection a. SCP: short circuited protection with auto-recovery function. b. OCP: Over current protection with auto recovery function. Current limit: 3A (max) at 115 Vac. c. OVP: Over voltage protection with auto-recovery function. Tripped voltage will be less than 18Vdc at any duration. 2.15 Transient Response Dynamic load condition. Vin (AC) DC output Vout Max Vout Min I1(A) I2(A) I1 time I2 time dI/dT 115Vac/60Hz 12V 12.6 11.4 0.2 2 5msec 5msec 0.1A/usec 3. Environment 3.1 Temperature a. Operation: 0 to 40 ℃ for nominal input condition. b. Storage: -40 to 70 ℃ 3.2 Humidity a. Operation: 5-95% for nominal input condition. b. Storage: 5-95%. Model No：PB-1240-6SA1 Page： 6 Revision：07 Date：05.21.2013 SPECIFICATION 4. Safety / EMC 4.1 Safety Safety referring Standards IEC / EN60950-1 2nd IEC / EN60065 4.2 EMS Test Item Test Specification IEC Standards Performance Criteria ESD Contact 8KV 61000-4-2 A ESD Air 15KV 61000-4-2 A RS FR : 80MHz-1.0GHz,Field Strength : 3V/M 61000-4-3 EFT 2KV on AC power line. 61000-4-4 CS FR: 150KHz-80MHz 3Vrms 61000-4-6 >95% reduction, 0.5 periods DIPS >30% reduction, 25 Periods A 61000-4-11 >95% reduction, 250 Periods Model No：PB-1240-6SA1 Page： 7 A A B Revision：07 Date：05.21.2013 SPECIFICATION Surge Immunity Tests: 1) +/-6kV Combination Wave: 2Ω, 1.2/50µSec ; N=5 strikes at + 6kV & N=5 strikes at -6kV per all noted modes {A, B & C} & all noted reference angles {A, B & C}. 2) +/-6kV Ring Wave: 12Ω; 0.5µS; N=5 strikes at + 6kV & N=5 strikes @ -6kV per all noted modes {A, B & C} & all noted reference angles {A, B & C}. 61000-4-5 Note 1: Modes : A) L to N SURGE 61000-4-12 B) N to PE ; C) L to PE Note 2: Reference Angles: A) 0° B) 90° C) 270° Note 3: Protective Earth {PE} is defined as DC output ground connection. Note 4: PS shall meet spec after test. No permanent damage allowed. Model No：PB-1240-6SA1 Page： 8 Revision：07 Date：05.21.2013 SPECIFICATION 4.3 EMI for both Conduction & Radiation Referring Standards Spec / Certified FCC Part 15,class B CISPR CISPR 22, class B 5. Reliability 5.1 Aluminum Capacitor Lifetime 61320 hours at full load & 90VAC, ambient temperature 40℃. 5.2 Burn-in 100% Burn-In with 80-100% loading & 30-40℃ Environment temperature. 5.3 Vibration Test Vibration of 1.25G peak, 5Hz-55Hz, constant acceleration swept from 0-60Hz with a two minute sweep time, and cycled from 60 minutes per each of three axes. 5.4 M.T.B.F Prediction: Minimum 100,000 hours @ 25 C SR-332 5.5 Acoustic The power supply must have a maximum sound pressure noise level of less than 25 dB at a distance of 1 meter under all operating conditions. Model No：PB-1240-6SA1 Page： 9 Revision：07 Date：05.21.2013 SPECIFICATION 6. Mechanical 6.1 Physical Size Plastic case size 112x52x31mm Outline Drawing 6.2 Input connector UL Pin. 6.3 Output connector DC output with traditional barrel 180 degrees angle type 5.5 x 2.5 x 9.5mm, 1.5M, UL2468 20AWG cable 6.4 Weight about 160g +/-10 g. 6.4 Flammability must meet 94V-0 and VW-1. Model No：PB-1240-6SA1 Page： 10 Revision：07 Date：05.21.2013