2016L150

POLYFUSE® Resettable PTCs Surface Mount 2016L Series Description The 2016L series device provides surface mount overcurrent protection for low voltage (≤60V) applications where resettable protection is desired. Features • RoHS compliant and lead-free • Fast response to fault currents Agency Approvals AGENCY AGENCY FILE NUMBER E183209 R50082521 • High voltage • Low-profile Applications • IEE1394 port protection • Powered ethernet port protection (IEEE 802.3 af) • Automotive electronic control module protection • Low voltage telecom equipment protection Electrical Characteristics I hold (A) 0.30 0.55 1.10 1.10 1.50 2.00 I trip (A) 0.60 1.10 2.20 2.20 3.00 4.20 V max (Vdc) 60 60 15 33 15 6 I max (A) 20 20 40 40 40 40 Pd max. (W) 1.40 1.40 1.40 1.40 1.40 1.40 Maximum Time To Trip Current (A) 1.50 2.50 8.00 8.00 8.00 8.00 Time (Sec.) 3.00 5.00 0.50 0.50 1.00 3.00 R min (Ω) 0.500 0.200 0.100 0.100 0.070 0.048 Resistance R typ (Ω) 1.400 0.700 0.250 0.250 0.130 0.070 R 1max (Ω) 2.300 1.000 0.400 0.400 0.180 0.100 X X X X X X X X X X X X Agency Approvals Part Number Marking 2016L030 2016L050 2016L100 2016L100/33 2016L150 2016L200 LF030 LF050 LF100 LF100-33 LF150 LF200 I hold = Hold current: maximum current device will pass without tripping in 20°C still air. I trip = Trip current: minimum current at which the device will trip in 20°C still air. V max = Maximum voltage device can withstand without damage at rated current (I max) I max = Maximum fault current device can withstand without damage at rated voltage (Vmax) P d = Power dissipated from device when in the tripped state at 20°C still air. R min = Minimum resistance of device in initial (un-soldered) state. R typ = Typical resistance of device in initial (un-soldered) state. R 1max = Maximum resistance of device at 20°C measured one hour after tripping or reflow soldering of 260°C for 20 sec. Caution: Operation beyond the specified rating may result in damage and possible arcing and flame. 2016L Series Specifications are subject to change without notice. 1 Electronics Designers Guide www.littelfuse.com ©2006 Littelfuse POLYFUSE® Resettable PTCs Surface Mount Temperature Rerating Ambient Operation Temperature -40°C Part Number 2016L030 2016L050 2016L100 2016L100/33 2016L150 2016L200 0.45 0.93 1.66 1.66 2.26 2.80 0.40 0.80 1.47 1.47 2.00 2.50 0.35 0.65 1.29 1.29 1.76 2.19 0.30 0.50 1.10 1.10 1.50 2.00 -20°C 0°C 23°C 40°C Hold Current (A) 0.25 0.38 0.91 0.91 1.24 1.84 0.23 0.32 0.83 0.83 1.13 1.74 0.20 0.25 0.73 0.73 1.00 1.50 0.18 0.19 0.64 0.64 0.87 1.34 0.14 0.09 0.50 0.50 0.68 1.14 50°C 60°C 70°C 85°C 2016L Average Time Current Curves Series Temperature Rerating Curve 100000 10000 1000 TIME IN SECONDS 100 10 1 1.00A 1.00A/33V 1.50A 2.00A 0.160A 0.300A 0.100 A: 2016L050 2016L100 2016L200 B: 2016L030 2016L100/33 2016L150 0.010 0.001 0.20 1 10 100 1000 CURRENT IN AMPERES Specifications are subject to change without notice. Note: 1.00 means the number one with two decimal places. AKL V3.9 06.05.10 The average time current curves and temperature rerating curve performance is affected by a number or variables, and these curves provided as guidance only. Customer must verify the performance in their application. 2016L Series Specifications are subject to change without notice. 2 Electronics Designers Guide www.littelfuse.com ©2006 Littelfuse POLYFUSE® Resettable PTCs Surface Mount Soldering Parameters Condition Peak Temp/ Duration Time Time above liquids (TAL) 220°C Preheat 120°C~ 180°C Storage Condition Reflow 260°C / 10 Sec 60 Sec ~ 100 Sec Temperature ( °C) 260 220 Soldering Cooling 50 Sec ~ 150 Sec 0°C~35°C, < 70%RH = • Recommended reflow methods: IR, vapor phase oven, hot air oven, N2 environment for lead-free • Devices are not designed to be wave soldered to the bottom side of the board. • Recommended maximum paste thickness is 0.25mm (0.010 inch) • Devices can be cleaned using standard industry methods and solvents. Note: If reflow temperatures exceed the recommended profile, devices may not meet the performance requirements. 180 120 Preheating 0 50 to 150 60 to 100 Time(s) 120 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material: Matte Tin(Sn)) Meets EIA Specification RS186-9E, ANSI/ J-STD-002 Category 3. Environmental Specifications Operating/Storage Temperature Maximum Device Surface Temperature in Tripped State Passive Aging Humidity Aging -40°C to +85°C 125°C +85°C, 1000 hours ±5% typical resistance change +85°C, 85%R.H. 1000 hours ±5% typical resistance change MIL-STD-202 Method 107G +85°C/-40°C 20 times -30% typical resistance change MIL-STD-202, Method 215 No change MIL-STD-883C, Method 2007.1, Condition A No change Thermal Shock Solvent Resistance Vibration 2016L Series Specifications are subject to change without notice.  Electronics Designers Guide www.littelfuse.com ©2006 Littelfuse POLYFUSE® Resettable PTCs Surface Mount Dimensions (mm) MARKING CODE VARIES WITH AMPERAGE AND VOLTAGE RATING (SEE CHART) SHOWN ARE: - 1.0A/15V RATING (LEFT) - 1.0A/33V RATING (RIGHT) A C Top View 100 100 D B 100 -33 Side View Bottom View Pad Layout E 3.40 mm (.133”) 4.60 mm (.181”) 1.50 mm (.059”) A Part Number 2016L030 2016L050 2016L100 2016L100/33 2016L150 2016L200 Inches 0.19 0.19 0.19 0.19 0.19 0.19 0.21 0.21 0.21 0.21 0.21 0.21 mm 4.72 4.72 4.72 4.72 4.72 4.72 5.44 5.44 5.44 5.44 5.44 5.44 Inches 0.15 0.15 0.15 0.15 0.15 0.15 0.17 0.17 0.17 0.17 0.17 0.17 B mm 3.7 3.7 3.7 3.7 3.7 3.7 4.43 4.43 4.43 4.43 4.43 4.43 Inches 0.03 0.05 0.02 0.03 0.03 0.02 0.05 0.08 0.03 0.05 0.06 0.03 C mm 0.75 1.2 0.5 0.75 0.75 0.5 1.25 2 0.75 1.25 1.55 0.75 D Inches mm Min. 0.03 0.03 0.03 0.03 0.03 0.03 0.01 0.01 0.01 0.01 0.01 0.01 Inches 0.01 0.01 0.01 0.01 0.01 0.01 0.03 0.03 0.03 0.03 0.03 0.03 E mm 0.25 0.25 0.25 0.25 0.25 0.25 0.65 0.65 0.65 0.65 0.65 0.65 Min Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Part Numbering System 2016 L 100 /33 D R PACKAGING STYLE R: Tape & Reel SERIES QUANTITY CODE: D=1500 M=1000 P=2000 /XX: SPECIAL VOLTAGE RATING (NOT APPLICABLE TO ALL PARTS) I HOLD CURRENT CODE (SEE TABLE BELOW) L: LITTELFUSE SURFACE MOUNT PPTC SIZE Packaging I hold (A) 0.30 0.55 1.10 1.50 2.00 I hold Code 030 050 100 150 200 /33 Voltage Option Packaging Option Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Tape and Reel Quantity 1500 1000 2000 1500 1500 2000 Quantity & Packaging Codes DR MR PR DR DR PR 2016L Series Specifications are subject to change without notice.  Electronics Designers Guide www.littelfuse.com ©2006 Littelfuse