HQ6025RH5

Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs HQ6025xH5 Series Description ® 25Amp bi-directional Alternistor Triac is designed for AC switching and phase control applications requiring a higher temperature environment. Alternistor type devices only operate in quadrants I, II, & and are used in circuits requiring high dv/dt capability. Features & Benefits temperature to 600 V to 300 A junctions Agency Approval Agency ® Agency File Number L and K Packages: E71639 Applications Typically used in high-temperature environments where available heat-sinking is minimal such as heating and white goods applications. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Main Features Symbol IT(RMS) VDRM /VRRM IGT Value 25 600 50 Unit A V mA Schematic Symbol MT2 MT1 G ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 129 Revised: May 10, 2010 09:33 PM HQ6025xH5 Series 25 A TRIACs Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Absolute Maximum Ratings Symbol Parameter HQ6025LH5 IT(RMS) RMS on-state current HQ6025RH5 HQ6025NH5 HQ6025KH5 Test Conditions TC = 95°C TC = 102°C single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C tp = 8.3ms f = 60Hz; TJ =150°C TJ = 150°C TJ = 150°C 25 A Value Unit 250 A 300 373 100 2 0.5 -40 to 150 -40 to 150 A2s A/μs A W °C °C ITSM Peak non-repetitive surge current I 2t di/dt IGTM PG(AV) Tstg TJ I2t Value for fusing Critical rate-of-rise of on-state current Peak gate current Average gate power dissipation Storage temperature range Operating junction temperature range Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol IGT VGT VGD IH dv/dt (dv/dt)c tgt Test Conditions VD = 12V; RL = 60 VD = VDRM; RL = 3.3 k IT = 400mA (initial) VD = VDRM; Gate Open; TJ = 150°C (di/dt)c = 13.3 A/ms; TJ = 150°C IG = 2 x IGT ; PW = 15μs; IT = 35.4 A ; TJ = 150°C Quadrant I – II – III I – II – III I – II – III MAX. MAX. MIN. MAX. MIN. MIN. TYP . Value 50 1.3 0.2 80 350 20 3 Unit mA V V mA V/μs V/μs μs Static Characteristics Symbol VTM IDRM / IRRM IT = 35.4A; tp = 380 μs VDRM / VRRM TJ = 25°C TJ = 150°C Test Conditions MAX. MAX. Value 1.4 5 6000 Unit V μA Thermal Resistances Symbol Parameter HQ6025LH5 R (J-C) Value 2.0 0.86 1.35 50 45 Unit Junction to case (AC) HQ6025RH5 HQ6025NH5 HQ6025KH5 °C/W R (J-A) Junction to ambient HQ6025LH5 HQ6025RH5 °C/W Note: xx = voltage HQ6025xH5 Series 130 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature 2.5 Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of IGT / IGT(TJ = 25°C) Ratio of VGT / VGT(TJ = 25°C) 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 -40 -15 10 35 60 85 110 135 150 0.0 -40 -15 10 35 60 85 110 135 150 Junction Temperature (TJ) -- (°C) Junction Temperature (TJ) -- (°C) Figure 3: Normalized DC Holding Current vs. Junction Temperature 2.0 Figure 4: On-State Current vs. On-State Voltage (Typical) 90 80 70 60 50 40 30 20 10 0 Ratio of IH / IH(TJ = 25°C) 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 135 150 Instantaneous On-state Current (iT) – Amps 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Junction Temperature (TJ) -- (°C) Instantaneous On-state Voltage (vT) – Volts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 45 Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current Maximum Allowable Case Temperature (TC) - °C 160 150 140 130 120 110 HQ6025LH5 100 90 80 0 5 10 15 20 25 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° Average On-State Power Dissipation [PD(AV)] -- Watts 40 35 30 25 20 15 10 5 0 0 5 10 15 20 25 30 35 40 HQ6025RH5 HQ6025NH5 HQ6025KH5 RMS On-State Current [IT(RMS)] -- Amps RMS On-State Current [IT(RMS)] - Amps ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 131 Revised: May 10, 2010 09:33 PM HQ6025xH5 Series 25 A TRIACs Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current Maximum Allowable Ambient Temperature (TA) - °C 160 140 120 100 80 60 40 20 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180° FREE AIR RATING RMS On-State Current [IT(RMS)] -- Amps Figure 8: Surge Peak On-State Current vs. Number of Cycles 1000 Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 10 1 10 100 1000 Surge Current Duration -- Full Cycles HQ6025xH5 Series 132 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Pb – Free assembly TP Temperature Ramp-up tP 150°C 200°C 60 – 180 secs 5°C/second max 5°C/second max 217°C 60 – 150 seconds 260+0/-5 °C 20 – 40 seconds 5°C/second max 8 minutes Max. 280°C TL TS(max) Preheat Preheat tL Ramp-do Ramp-down tS 25 time to peak temperature Time Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed Physical Specifications Terminal Material Copper Alloy Environmental Specifications Test High Temperature Voltage Blocking Temperature Cycling Specifications and Conditions MIL -STD-750: Method 1040, Condition A Rated VRRM, 150°C, 1008 hours MIL -STD-750: Method 1051 -40°C to 150°C, 15-minute dwell, 100 cycles EIA/JEDEC: JESD22-A101 320VDC, 85°C, 85%RH, 1008 hours MIL -STD-750: Method 1031 150°C, 1008 hours -40°C, 1008 hours MIL -STD-750: Method 1056 0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles Terminal Finish 100% Matte Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Body Material Biased Temp & Humidity High Temp. Storage Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage Thermal Shock Autoclave EIA/JEDEC: JESD22-A102 (Pressure Cooker Test) 121°C, 100%RH, 2atm, 168 hours Resistance to Solder Heat Solderability Lead Bend MIL -STD-750: Method 2031 260°C, 10 seconds ANSI/J-STD-002, Category 3, Test A MIL -STD-750: Method 2036, Condition E ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 133 Revised: May 10, 2010 09:33 PM HQ6025xH5 Series 25 A TRIACs TS(min) Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT O ØE A MT2 B AREA (REF.) 0.17 IN2 8.13 .320 Dimension A B C D E F G H J K L M N O P R Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048 Millimeters Min 9.65 2.67 5.84 14.99 3.61 2.79 13.72 0.64 4.95 2.41 1.52 2.16 0.46 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 3.73 3.30 14.61 0.89 5.21 2.67 1.91 2.41 0.61 4.78 1.52 1.22 P C D 7.01 .276 13.36 .526 F G L H R NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB K J MT1 MT2 GATE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm.) Dimensions — TO- 220AB (L Package) — Isolated Mounting Tab TC MEASURING POINT O ØE A P 8.13 .320 AREA (REF.) 0.17 IN2 Dimension A B C D E F G H J K L M N O P R Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048 Millimeters Min 9.65 2.67 5.84 14.99 3.61 2.79 13.72 0.64 4.95 2.41 1.52 2.16 0.46 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 3.73 3.30 14.61 0.89 5.21 2.67 1.91 2.41 0.61 4.78 1.52 1.22 B C D 7.01 .276 13.36 .526 F G L H R K J MT1 MT2 GATE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm.) HQ6025xH5 Series 134 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Dimensions — TO- 218AC (K Package) — Isolated Mounting Tab TC Measurement Point B U (diameter) M Package MT2 / Anode C D Dimension A B C D E F G H J K L M N P Q R U W Inches Min 0.810 0.610 0.178 0.055 0.487 0.635 0.022 0.075 0.575 0.211 0.422 0.058 0.045 0.095 0.008 0.008 0.159 0.085 Max 0.835 0.630 0.188 0.070 0.497 0.655 0.029 0.095 0.625 0.219 0.437 0.068 0.055 0.115 0.016 0.016 0.163 0.095 Millimeters Min 20.57 15.49 4.52 1.40 12.37 16.13 0.56 1.91 14.61 5.36 10.72 1.47 1.14 2.41 0.20 0.20 4.04 2.17 Max 21.21 16.00 4.78 1.78 12.62 16.64 0.74 2.41 15.88 5.56 11.10 1.73 1.40 2.92 0.41 0.41 4.14 2.42 A F E W Gate P MT1 MT2 M Q R N H G J K L Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Dimensions — TO-263AB (N-Package) — D2 -PAK Surface Mount T TC MEASURING POIN B MT2 V C E AREA: 0.1 IN2 1 Dimension 8.41 .331 Inches Min 0.360 0.380 0.178 0.025 0.045 0.060 0.095 0.092 0.018 0.090 0.590 0.035 0.002 0.040 Max 0.370 0.420 0.188 0.035 0.060 0.075 0.105 0.102 0.024 0.110 0.625 0.045 0.010 0.070 Millimeters Min 9.14 9.65 4.52 0.64 1.14 1.52 2.41 2.34 0.46 2.29 14.99 0.89 0.05 1.02 Max 9.40 10.67 4.78 0.89 1.52 1.91 2.67 2.59 0.61 2.79 15.88 1.14 0.25 1.78 A B C D E F G H J K A S W GATE G D F 1 1.68 .460 2.16 .085 H K 7 01 . .276 U J 8.13 .320 MT1 7 01 . .276 16.89 .665 8.89 .350 7 01 . .276 S V U W 1.40 .055 3.81 .150 2.03 .080 6.60 .260 Product Selector Part Number HQ6025RH5 HQ6025NH5 HQ6025LH5 HQ6025KH5 Voltage 400V 600V X X X X 800V 1000V Gate Sensitivity 50 mA 50 mA 50 mA 50 mA Package TO-220R TO-263 TO-220L TO-218K ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 135 Revised: May 10, 2010 09:33 PM HQ6025xH5 Series 25 A TRIACs Teccor® brand Thyristors 25 Amp High Temperature Alternistor Triacs Packing Options Part Number HQ6025RH5 HQ6025RH5TP HQ6025NH5TP HQ6025NH5RP HQ6025LH5TP HQ6025KH5TP Marking HQ6025RH5 HQ6025RH5 HQ6025NH5 HQ6025NH5 HQ6025LH5 HQ6025KH5 Weight 2.2g 2.2g 1.6g 1.6g 2.2g 4.4g Packing Mode Bulk Tube Tube Embossed Carrier Tube Tube Base Quantity 500 500 (50 per tube) 500 (50 per tube) 500 500 (50 per tube) 250 (25 per tube) TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DI A (1.5) MT1 0.945 (24.0) 0.827 * (21.0) * Co ver tape MT2 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed Part Numbering System HQ 60 25 L H5 81 DEVICE TYPE HQ: Triac VOLTAGE RATING 60: 600V LEAD FORM DIMENSIONS xx: Lead Form Option SENSITIVITY & TYPE H5: 50mA PACKAGE TYPE L: TO-220 AB (Isolated) K: TO-218 AC (Isolated) R: TO-220AB (Non-isolated) N: TO-263 (D2 Pak) Part Marking System TO-220AB (R and L Packages) TO-263 (N Package) TO-218AC (K Package) HQ6025KH5 HQ6025LH5 yxxxx CURRENT RATING 25: 25A yxxxx HQ6025xH5 Series 136 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.