P0641CA2

Twin SLIC Protector Twin SLIC Protector 1 (T) 3 (R) 2 (G) Subscriber Line Interface Circuits (SLIC) are highly susceptible to transient voltages, such as lightning and power cross conditions. To minimize this threat, Teccor provides this dualchip, fixed-voltage SLIC protector device. For specific design criteria, see details in Figure 3.29. Electrical Parameters Part Number * P0641CA2 P0721CA2 P0901CA2 P1101CA2 VDRM Volts 58 65 75 95 VS Volts 77 88 98 130 VT Volts 4 4 4 4 VF Volts 5 5 5 5 IDRM µAmps 5 5 5 5 IS mAmps 800 800 800 800 IT Amps 1 1 1 1 IH mAmps 120 120 120 120 CO pF 60 60 60 60 Pins 1-2, 3-2 * For surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • VDRM is measured at IDRM. • VS and VF are measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance is measured across pins 1-2 or 3-2 at 1 MHz with a 2 V bias. Capacitance across pins 1-3 is approximately half. • Parallel capacitive loads may affect electrical parameters. • Compliance with GR 1089 or UL 60950 power cross tests may require special design considerations. Contact the factory for further information. Surge Ratings (Preliminary Data) IPP 2x10 µs Amps 150 IPP 8x20 µs Amps 150 IPP 10x160 µs Amps 90 IPP 10x560 µs Amps 50 IPP 10x1000 µs Amps 45 ITSM 60 Hz Amps 20 di/dt Amps/µs 500 Series A http://www.teccor.com +1 972-580-7777 2 - 54 © 2004 Littelfuse LP SIDACtor® Data Book and Design Guide Twin SLIC Protector Thermal Considerations Package Modified DO-214AA Pin 3 Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 85 Unit °C °C °C/W Pin 1 +I +I IPP – Peak Pulse Current – %IPP VF tr = r ise time to peak value td = decay time to half value IT IS IH IDRM VT 100 Peak Value VS VDRM -V -V VT Waveform = tr x td IDRM VDRM IH IS IT +V +V 50 Half Value VS 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form 14 Percent of VS Change – % 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH IH (TC = 25 ˚C) 10 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature © 2004 Littelfuse LP SIDACtor® Data Book and Design Guide 2 - 55 http://www.teccor.com +1 972-580-7777 Data Sheets Pin 2