P0641DF-1

SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Single Port Series - MS-012 Description The MS-012 packaged Fixed Voltage Single Port Series are SIDACtor® devices designed to protect sensitive SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single port protection using a fixed voltage switching device for negative surges. Positive surges are routed though internal diodes to a ground reference. The series is also pin-to-pin compatible to industry standard programmable SO-8 SLIC protectors. Features & Benefits Agency Approvals Agency Agency File Number E133083 positive voltage surges surged in excess of ratings one package footprint Pinout (Tip) (NC) (NC) (Ring) 1 2 3 4 8 7 6 5 (Tip) (Ground) (Ground) (Ring) Applicable Global Standards Level Schematic Symbol 1 8 2 3 7 6 * Series resistance required 4 5 Electrical Characteristics VDRM@ IDRM=5μA V min P0641DF-1 P0721DF-1 P0901DF-1 P1001DF-1 P1101DF-1 P0641F1 P0721F1 P0901F1 P1001F1 P1101F1 58 65 75 85 95 VS@100V/μs V max 77 88 98 110 130 IH mA min 150 150 150 150 150 IS mA max 800 800 800 800 800 IT@VT A max 1 1 1 1 1 VT@IT=1 Amps V max 5 5 5 5 5 VF@25° V max 5 5 5 5 5 Part Number Marking Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pins 1 & 8) to Ground (pins 6 & 7), and Ring (pins 4 & 5) to ground (pins 6 & 7) - VF > 8.5 volts @ 10 x 700μs, 37 Amps .5 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 101 Fixed Voltage Single SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1,8-6,7 / 4,5-6,7 Tip-Ground, Ring-Ground MIN MAX 40 90 35 85 30 80 25 75 25 70 pF Pin 1,8-4,5 Tip-Ring MIN MAX 20 45 20 45 20 40 15 35 15 30 Part Number P0641DF-1 P0721DF-1 P0901DF-1 P1001DF-1 P1101DF-1 Fixed Voltage Single Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series 2x10μs A min F 120 1.2x50μs/8x20μs A min 100 10x700/5x310μs A min 50 10x1000μs A min 30 ITSM 600VRMS 1s A min 1 di/dt Amps/μs max 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package MS-012 8 7 6 Symbol TJ 5 Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C TS 1 2 3 4 R0JA 120 °C/W V-I Characteristics +I VF tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td VS VDRM -V VT +V IDRM IH IS IT -I 50 Half Value 0 0 tr td t – Time (μs) 102 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors SLIC Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 14 2.0 Percent of VS Change – % 10 IH (TC = 25ºC) 12 1.8 1.6 1.4 1.2 1.0 0.8 6 4 2 0 -4 -6 -8 -40 -20 0 IH 8 25 °C 25°C Ratio of 0.4 20 40 60 80 100 120 140 160 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Case Temperature (TC) - ºC Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VDC 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 103 Fixed Voltage Single 0.6 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-012 Inches MIN MAX 0.053 0.069 0.004 0.010 0.043 0.065 0.012 0.020 0.007 0.010 0.189 0.197 0.228 0.244 0.150 0.157 0.050 BSC* 0.016 0.050 Millimeters MIN MAX 1.35 1.75 0.10 0.25 1.25 1.65 0.31 0.51 0.17 0.25 4.80 5.00 5.80 6.20 3.80 4.00 1.27 BSC* 0.40 1.27 Dimension A A1 A2 B C D E E1 e L o Recommended Soldering Pad Outline (Reference Only) Fixed Voltage Single * BSC = Basic Spacing between Centers Part Numbering Part Marking P xxx 1 D F -1 TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE SINGLE IPP RATING Part Number Code XXXXXF1 o XXXXX (Refer to Electrical Characteristics Table) PACKAGE TYPE Date Code Packing Options Package Type D Description MS-012 SMT 8-pin SOIC Tape and Reel Pack Quantity 2500 Added Suffix N/A Industry Standard EIA-481-D Tape and Reel Specifications — MS-012 4.0 (.158) 8.0 (.315) 2.0 (.079) 1.55 (.061) DIMENSIONS ARE: MILLIMETERS (INCHES) 0.40 (0.016) 0.8 MIN. (0.03) 5.5 (.216) o 12.0 (.472) 6.4 (.252) 1.50 ø MIN. (.059) 0 MIN. 2.1 (.083) Cover Tape Carrier Tape Embossment Direction of Feed 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed 104 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.