P0644UCMCLXX

SIDACtor ® Protection Thyristors Broadband Optimized™ Protection MC Multiport Series - MS-013 Description MC Multiport Series MS-013 are low capacitance SIDACtor® devices designed to protect broadband equipment from damaging overvoltage transients. The series provides a dual port surface mount solution that enables equipment to comply with various global regulatory standards while limiting the impact to broadband signals. Features and Benefits Low voltage overshoot Agency Approvals Agency Agency File Number E133083 Low on-state voltage Does not degrade with use Fails short circuit when surged in excess of ratings Two-pair protection 6 5 4 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Replaces four discrete devices Pinout Designation 1 2 3 Applicable Global Standards TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol (T1) 1 (G1) 2 (R1) 3 6 (T2) 5 (G2) 4 (R2) ITU K.20/21 Basic Level GR 1089 Inter-building Electrical Characteristics VS VDRM VS VDRM @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs V P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx P0084UCMC P0304UCMC P0644UCMC P0724UCMC P0904UCMC P1104UCMC P1304UCMC 6 25 58 65 75 90 120 V 25 40 77 88 98 130 160 V 12 50 116 130 150 180 240 V 50 80 154 176 196 260 320 Pins 1-2, 3-2, 4-5, 6-5 Pins 1-3, 4-6 IH IS IT VT @IT= 2.2 Amps V max 8 8 8 8 8 8 8 Part Number Marking Capacitance mA min mA max A max 50 50 150 150 150 150 150 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 67 Revised: February 22, 2011 Table continues on next page. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Electrical Characteristics (continued) VDRM VS VDRM VS @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs Part Number Marking V V V V mA min mA max A max 150 150 150 150 150 150 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 V max 8 8 8 8 8 8 VT @IT= 2.2 Amps Capacitance IH IS IT Pins 1-2, 3-2, 4-5, 6-5 P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLxx P1504UCMC P1804UCMC P2304UCMC P2604UCMC P3104UCMC P3504UCMC 140 170 190 220 275 320 180 220 260 300 350 400 Pins 1-3, 4-6 280 340 380 440 550 600 360 440 520 600 700 800 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). Capacitance Values pF Pin 1-2 / 3-2 (4-5 / 6-5) Tip-Ground, Ring-Ground MIN P0084UCMCLxx P0304UCMCLxx P0644UCMCLxx P0724UCMCLxx P0904UCMCLxx P1104UCMCLxx P1304UCMCLxx P1504UCMCLxx P1804UCMCLxx P2304UCMCLxx P2604UCMCLxx P3104UCMCLxx P3504UCMCLXx 35 25 55 50 45 45 40 35 35 30 30 30 25 MAX 75 45 85 75 70 70 60 55 50 50 45 45 40 pF Pin 1-3 (4-6) Tip-Ring MIN 20 10 30 25 25 25 20 20 15 15 15 15 15 MAX 45 25 50 45 40 40 35 35 30 30 30 25 25 Part Number Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series 0.2x310 0.5x700 2 1 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 150 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 ITSM 50/60 Hz A min 30 di/dt A/μs max 500 A min C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 500 A min 400 A min 200 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 68 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Thermal Considerations Package Modified MS-013 6 5 4 1 2 3 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 60 °C/W V-I Characteristics +I tr x td Pulse Waveform tr = r ise time to peak value td = decay time to half value IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change – % IH (TC = 25ºC) 14 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Ratio of Junction Temperature (TJ) – °C Case Temperature (TC) - ºC © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 69 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) TL TS(max) Preheat 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy Temp Cycling 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Part Numbering P xxx 4 U C MC L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT MC Series Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level IPP RATING Part Marking XXXXXXXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 70 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Dimensions — MS-013 Dimensions Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters). Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 0.143 Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 3.63 7º TYP A D 7º TYP G A J H Burr Side 96º 4º 7º TYP B A F 7º TYP MIN Length of Flat K Detail A Mold Split Line BSC* A B C D E F G H J K BSC* * BSC = Basic Spacing between Centers Packing Options Package Type Description Quantity Added Suffix Industry Standard U Modified MS-013 6-pin Tape and Reel Pack Modified MS-013 6-pin Tube Pack 1500 500 (50 per tube) RP TP EIA-481-D N/A Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .512 (13.0) Arbor Hole Dia. .472 (12.0) 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Dimensions — MS-013 Message Location .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .110 (2.79) .045 (1.14) 90˚ .165 (4.19) .310 (7.87) 6 Interior of the Tube 20.000 ± .030 (508.00 ± 0.76) .005 A .150 (3.81) .225 (5.72) .525 (13.34) A Dimensions are in inches (and millimeters) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 71 Revised: February 22, 2011