P0720ECLXXX

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - TO-92 Description SIDACtor® Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a robust through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Does not degrade with use Applicable Global Standards TIA-968-A Fails short circuit when surged in excess of ratings Low Capacitance GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Pinout Designation TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level Pin 3 GR 1089 Inter-building* * A/B-rated parts require series resistance Pin 1 Schematic Symbol Electrical Characteristics VDRM @lDRM=5μA V min P0080EALxxx P0300EALxxx P0640EALxxx P0720EALxxx P0900EALxxx P1100EALxxx P1300EALxxx P1500EALxxx P1800EALxxx P2300EALxxx P2600EALxxx P3100EALxxx P3500EALxxx P0080EA P0300EA P0640EA P0720EA P0900EA P1100EA P1300EA P1500EA P1800EA P2300EA P2600EA P3100EA P3500EA 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/μs V max 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF min pF max 25 15 40 35 35 30 25 25 25 25 20 20 20 150 140 60 60 55 50 45 40 35 35 35 35 35 Part Number Marking mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 Table continues on next page. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 158 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) VDRM @lDRM=5μA V Min P0080EBLxxx P0300EBLxxx P0640EBLxxx P0720EBLxxx P0900EBLxxx P1100EBLxxx P1300EBLxxx P1500EBLxxx P1800EBLxxx P2300EBLxxx P2600EBLxxx P3100EBLxxx P3500EBLxxx P0080ECLxxx P0300ECLxxx P0640ECLxxx P0720ECLxxx P0900ECLxxx P1100ECLxxx P1300ECLxxx P1500ECLxxx P1800ECLxxx P2300ECLxxx P2600ECLxxx P3100ECLxxx P3500ECLxxx P0080EB P0300EB P0640EB P0720EB P0900EB P1100EB P1300EB P1500EB P1800EB P2300EB P2600EB P3100EB P3500EB P0080EC P0300EC P0640EC P0720EC P0900EC P1100EC P1300EC P1500EC P1800EC P2300EC P2600EC P3100EC P3500EC 6 25 58 65 75 90 120 140 170 190 220 275 320 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/μs V Max 25 40 77 88 98 130 160 180 220 260 300 350 400 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A Max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V Max 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF Min pF Max 25 15 40 35 35 30 25 25 25 25 20 20 20 35 25 55 50 45 45 40 35 35 30 30 30 25 150 140 60 75 70 70 60 55 50 50 45 45 40 260 250 155 150 140 115 105 95 90 80 80 70 65 Part Number Marking mA Min mA Max 50 50 150 150 150 150 150 150 150 150 150 150 150 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - xxx part number suffix: ‘AP’ = Ammo Pack, ‘RP1’ and ‘RP2’ = Reel Pack, blank = Bulk Pack Surge Ratings Series IPP 0.2x310 1 0.5x700 2 A min A B C Notes: 1 Current waveform in μs 2 Voltage waveform in μs 2x10 1 2x10 2 A min 150 250 500 8x20 1 1.2x50 2 A min 150 250 400 10x160 1 10x160 2 A min 90 150 200 10x560 1 10x560 2 A min 50 100 150 5x320 1 9x720 2 A min 75 100 200 10x360 1 10x360 2 A min 75 125 175 10x1000 1 10x1000 2 A min 45 80 100 5x310 1 10x700 2 A min 75 100 200 ITSM 50/60 Hz A min 20 25 30 di/dt A/μs max 500 500 500 20 25 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package TO-92 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit °C °C °C/W © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 159 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) V-I Characteristics +I tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change – % IH (TC = 25ºC) 14 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Junction Temperature (TJ) – °C Ratio of Case Temperature (TC) - ºC Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 160 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking P xxx 0 E x L xxx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS RoHS COMPLIANT IPP RATING XXXXXXX XX XXXXX Part Marking Code Date Code (Refer to Electrical Characteristics Table) Packing Options Package Type Description Packing Options Quantity Added Suffix RP1 TO-92 Tape and Reel Pack E TO-92 Ammo Pack TO-92 Bulk Pack 2000 RP2 AP N/A Lead Spacing Industry Standard 0.1 inch (2.54mm) 0.2 inch (5.08mm) EIA-481-D EIA-468-B N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 161 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions — TO-92 Temperature Measurement Point Ammo Pack Specification — TO-92 Inches Min Max 0.196 0.105 0.145 0.096 0.186 0.096 0.019 0.017 0.60 Millimeters Min 4.47 12.70 2.41 3.81 3.43 2.23 4.47 2.23 0.33 0.33 3.68 2.44 4.73 2.44 0.48 0.43 1.52 Dimensions are in inches (and millimeters). 0.50 (12.7) 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 0.50 (12.7) 0.25 (6.35) 0.125 (3.2) MAX Max 4.98 2.67 A N A B D E 0.176 0.500 0.095 0.150 0.135 0.088 0.176 0.088 0.013 0.013 1.27 (32.2) 0.157 DIA (4.0) 0.20 (5.08) Flat down B G H J K L Directio n of Fe ed 25 Devices per fold MT1/PIN 1 E MT2/PIN 3 M N 1.7 (43) M L D J H G K All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side. 6.9 (175) The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 1.7 (43) 12.9 (327) Tape and Reel Specification — TO-92 FLAT SIDE OF TO-92 Dimensions A B C Inches Min N/A 4.016 3.386 0.795 1.181 0.496 0.498 0.090 0.182 N/A N/A 0.674 0.354 0.236 0.020 Max 14.173 N/A N/A N/A 1.968 0.504 0.502 0.110 0.244 1.673 1.270 0.763 0.370 N/A N/A Millimeters Min N/A 102.0 86.0 20.2 30.0 12.60 12.65 2.29 4.63 N/A N/A 17 .12 8.25 6.00 0.50 Max 360.0 N/A N/A N/A 50.0 12.80 12.75 2.80 6.19 42.50 32.26 19.38 9.75 N/A N/A A D C B W1 D W1 P ROUND SIDE OF TO-92 P0 F(for RP1) F(for RP2) P H1 H W W2 W3 W4 (RP1) (RP2) H H1 W W2 W3 W4 P0 F F © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 162 Revised: February 22, 2011