P0720SCMC

MicroCapacitance (MC) SC SIDACtor Device MicroCapacitance (MC) SC SIDACtor Device The DO-214AA SC MC SIDACtor series is intended for applications sensitive to load values. Typically, high speed connections require a lower capacitance. CO values for the MicroCapacitance device are 40% lower than a standard SC part. This MC SIDACtor series is used to enable equipment to meet various regulatory requirements including GR 1089, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Contact factory regarding ITU K.20, K.21, and K.45. Electrical Parameters Part Number * P0080SC MC P0300SC MC P0640SC MC P0720SC MC P0900SC MC P1100SC MC P1300SC MC P1500SC MC P1800SC MC P2300SC MC P2600SC MC P3100SC MC P3500SC MC VDRM Volts 6 25 58 65 75 90 120 140 170 190 220 275 320 VS Volts 25 40 77 88 98 130 160 180 220 260 300 350 400 VT Volts 4 4 4 4 4 4 4 4 4 4 4 4 4 IDRM µAmps 5 5 5 5 5 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 50 50 150 150 150 150 150 150 150 150 150 150 150 CO pF 55 35 60 60 60 50 50 50 40 40 40 40 40 * For surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP 2x10 µs Amps 500 IPP 8x20 µs Amps 400 IPP 10x160 µs Amps 200 IPP 10x560 µs Amps 150 IPP 10x1000 µs Amps 100 ITSM 60 Hz Amps 30 di/dt Amps/µs 500 Series C http://www.littelfuse.com +1 972-580-7777 2-6 © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide MicroCapacitance (MC) SC SIDACtor Device Thermal Considerations Package DO-214AA Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 90 Unit °C °C °C/W +I +I IPP – Peak Pulse Current – %IPP tr = r ise time to peak value td = decay time to half value IT IT IS S IH IDRM -V -V VT VT VDRM VDRM VS V S 100 Peak Value Waveform = tr x td +V +V 50 Half Value 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form 14 Percent of VS Change – % 10 IH (TC = 25 ˚C) 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide 2-7 http://www.littelfuse.com +1 972-580-7777 Data Sheets