P1100ECMCLXXX

SIDACtor ® Protection Thyristors Broadband Optimized™ Protection MC Series - TO-92 Description MC Series TO-92 are low capacitance SIDACtor® devices designed to protect broadband CPE equipment such as VoIP and DSL Modems from damaging overvoltage transients. The series provides a through-hole solution that enables CPE equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features and Benefits Low voltage overshoot Agency Approvals Agency Agency File Number E133083 Low on-state voltage Does not degrade with use Fails short circuit when surged in excess of ratings Applicable Global Standards TIA-968-A 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Pinout Designation GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Pin 1 Schematic Symbol Pin 3 TIA-968-B ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building Electrical Characteristics VDRM @lDRM=5μA V min P0080ECMCLxxx P0300ECMCLxxx P0640ECMCLxxx P0720ECMCLxxx P0900ECMCLxxx P1100ECMCLxxx P1300ECMCLxxx P1500ECMCLxxx P1800ECMCLxxx P2300ECMCLxxx P2600ECMCLxxx P3100ECMCLxxx P3500ECMCLxxx P0080ECMC P0300ECMC P0640ECMC P0720ECMC P0900ECMC P1100ECMC P1300ECMC P1500ECMC P1800ECMC P2300ECMC P2600ECMC P3100ECMC P3500ECMC 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/μs V max 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHz, 2V bias pF min 35 25 55 50 45 45 40 35 35 30 30 30 25 pF max 75 45 85 75 70 70 60 55 50 50 45 45 40 Part Number Marking mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XXX Part Number Suffix: ‘AP’ (Ammo Pack), or ‘RP1’ or ‘RP2’ (Reel Pack),. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 76 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Surge Ratings IPP 0.2x310 1 0.5x700 2 A min C Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Series 2x10 1 2x10 2 A min 500 8x20 1 1.2x50 2 A min 400 10x160 1 10x160 2 A min 200 10x560 1 10x560 2 A min 150 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 ITSM 50/60 Hz A min 30 di/dt A/μs Max 500 50 Thermal Considerations Package TO-92 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 90 Value Unit °C °C °C/W V-I Characteristics +I tr x td Pulse Waveform tr = r ise time to peak value td = decay time to half value IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 14 Percent of VS Change – % 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Ratio of Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Case Temperature (TC) - ºC 77 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking P xxx 0 E C MC L xxx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS RoHS COMPLIANT MC SERIES IPP RATING XXXXXXX XX XXXXX Part Marking Code Date Code (Refer to Electrical Characteristics Table) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 78 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Packing Options Package Type Packing Options Quantity Description TO-92 Tape and Reel Pack Added Suffix RP1 Lead Spacing Industry Standard 0.1 inch (2.54mm) 0.2 inch (5.08mm) (Not applicable) (Not applicable) E TO-92 Ammo Pack TO-92 Bulk Pack 2000 RP2 AP N/A EIA-481-D EIA-468-B N/A Dimensions — TO-92 Temperature Measurement Point Ammo Pack Specification — TO-92 Inches Millimeters Min 4.47 12.70 0.105 0.145 0.096 0.186 0.096 0.019 0.017 0.60 2.41 3.81 3.43 2.23 4.47 2.23 0.33 0.33 3.68 2.44 4.73 2.44 0.48 0.43 1.52 Dimensions are in inches (and millimeters). 6.9 (175) 1.7 (43) 25 Devices per fold 0.50 (12.7) 0.02 (0.5) 1.62 0.236 (41.2) (6.0) MAX 0.708 (18.0) 0.354 (9.0) 0.50 (12.7) 0.25 (6.35) 0.125 (3.2) MAX A N Min A B D E 0.176 0.500 0.095 0.150 0.135 0.088 0.176 0.088 0.013 0.013 Max 0.196 Max 4.98 2.67 1.27 (32.2) 0.157 DIA (4.0) 0.20 (5.08) ed B G H J K L Directio n of Fe Flat down MT1/PIN 1 E MT2/PIN 3 M N M L D J H G K All leads are insulated from case. Case is electrically non-conductive. (Rated at 1600 V(AC) RMS for one minute from leads to case over the operating temperature range.) Mold flash shall not exceed 0.13 mm per side. The TO-92 is designed to meet mechanical standards as set forth in JEDEC publication number 95. 1.7 (43) 12.9 (327) Tape and Reel Specification — TO-92 FLAT SIDE OF TO-92 Inches Min A B C D W1 P P0 F(for RP1) F(for RP2) H H1 W W2 W3 W4 N/A 4.016 3.386 0.795 1.181 0.496 0.498 0.090 0.182 N/A N/A 0.674 0.354 0.236 0.020 Max 14.173 N/A N/A N/A 1.968 0.504 0.502 0.110 0.244 1.673 1.270 0.763 0.370 N/A N/A Millimeters Min N/A 102.0 86.0 20.2 30.0 12.60 12.65 2.29 4.63 N/A N/A 17 .12 8.25 6.00 0.50 Max 360.0 N/A N/A N/A 50.0 12.80 12.75 2.80 6.19 42.50 32.26 19.38 9.75 N/A N/A A D C B W1 P ROUND SIDE OF TO-92 H1 H W W2 W3 W4 (RP1) (RP2) P0 F F © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 79 Revised: February 22, 2011