P1100G_LRP

Teccor® brand Protection Thyristors Axial Leaded DO-15 Series (A/B Rated) SIDACtor® Device Description This DO-15 plastic package provides a through-hole version of the SIDACtor® device. This axial leaded device is ideal for Customer Premises Equipment (CPE) such as telephones, answering machines, modems, fax interfaces. The DO-15 package series can also be used for overvoltage protection for applications such as T1/E1/J1 trunk cards when the appropriate overcurrent protection is included. Features Agency Approvals Agency Agency File Number E133083 • RoHS compliant • Bidirectional transient voltage protection • Axial lead through-hole component • Teccor brand SIDACtor technology Protection solution to meet • YD/T 950 • YD/T 993 • YD/T 1082 • GR 1089 Intra-building • IEC 61000-4-5 • ITU K.20/21 Basic Level • TIA-968-A Electrical Characteristics VDRM @lDRM=5µA Volts Min 90 120 140 170 190 220 275 320 VS @100V/µs Volts Max 130 160 180 220 260 300 350 400 IH IS IT Amps Max 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 VT @IT=1 amp Volts Max 5 5 5 5 5 5 5 5 Min 30 25 25 25 25 25 20 20 Capacitance @1MHz, 2V bias pF Max 60 40 40 40 30 30 30 30 Part Number “_” = A or B Marking “_” = A or B mAmps mAmps Min 150 150 150 150 150 150 150 150 Max 800 800 800 800 800 800 800 800 P1100G_LRP P1300G_LRP P1500G_LRP P1800G_LRP P2300G_LRP P2600G_LRP P3100G_LRP P3500G_LRP P11_ P13_ P15_ P18_ P23_ P26_ P31_ P35_ • All measurements are made at an ambient temperature of 25°C. • Listed SIDACtor devices are bidirectional. All electrical parameters and surge ratings apply to forward and reverse polarities. DO-15 Series (A/B Rated) Specifications are subject to change without notice. 1 Telecom Design Guide www.littelfuse.com ©2006 Littelfuse Teccor® brand Protection Thyristors Axial Leaded Surge Ratings IPP Series 10x1000 µs Amps Min 10x560 µs Amps Min A B 45 80 100 • IPP applies to -40°C through +85°C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. V-I Characteristics +I tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP IT IS IH -V IDRM VT VDRM VS +V 100 Peak Value tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td -I t – Time (µs) Normalized VS Change Versus Junction Temperature Normalized DC Holding Current Versus Case Temperature 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 Percent of VS Change – % 8 6 4 2 0 IH 10 IH (TC = 25 ˚C) 14 12 25 ˚C 25 ˚C -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Ratio of Junction Temperature (TJ) – ˚C Case Temperature (TC) – ˚C 20 40 60 80 100 120 140 160 DO-15 Series (A/B Rated) Specifications are subject to change without notice.  Telecom Design Guide www.littelfuse.com ©2006 Littelfuse Teccor® brand Protection Thyristors Axial Leaded Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (ts) Pb – Free assembly 150°C 190°C 60 – 150 seconds 5°C/second max 5°C/second max 220°C >60 –