P1101DF-1E

SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Enhanced Single Port Series - MS-012 Description The MS-012 packaged Fixed Voltage Enhanced Single Port Series are SIDACtor® devices designed to protect sensitive SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single port protection using a fixed voltage switching device for negative surges. Positive surges are routed though enhanced switching diodes to a ground reference. The series is also pin-to-pin compatible to industry standard programmable SO-8 SLIC protectors. Features & Benefits diodes for positive voltage surges one package Pinout footprint (Tip) (NC) (NC) (Ring) 1 2 3 4 8 7 6 5 Agency Approvals Agency Agency File Number E133083 surged in excess of ratings (Tip) (Ground) (Ground) (Ring) Applicable Global Standards Level Schematic Symbol 1 8 2 3 7 6 4 5 Electrical Characteristics VDRM@ IDRM=5μA V min P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1701DF-1E P0641F1E P0721F1E P0901F1E P0991F1E P1001F1E P1101F1E P1301F1E P1701F1E 58 65 75 80 85 95 120 160 VS@100V/μs V max 77 88 98 104 110 130 160 200 IH mA min 150 150 150 150 150 150 150 150 IS mA max 800 800 800 800 800 800 800 800 IT@VT A max 1 1 1 1 1 1 1 1 VT@IT=1 Amps V max 5 5 5 5 5 5 5 5 VF@25° V max 5 5 5 5 5 5 5 5 Part Number Marking Capacitance See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - VF < 8.5 volts @ 10 x 700μs Amps © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 105 Fixed Voltage Enh. Single SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1,8-6,7 / 4,5-6,7 Tip-Ground, Ring-Ground MIN MAX 40 90 35 85 30 80 25 75 25 75 25 70 20 70 20 70 pF Pin 1,8-4,5 Tip-Ring MIN MAX 20 45 20 45 20 40 15 35 15 35 15 30 15 30 15 30 Part Number P0641DF-1E P0721DF-1E P0901DF-1E P0991DF-1E P1001DF-1E P1101DF-1E P1301DF-1E P1701DF-1E Fixed Voltage Enh. Single Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series 2x10μs A min F 120 1.2x50μs/8x20μs A min 100 10x700/5x310μs A min 50 10x1000μs A min 30 ITSM 600VRMS 1s A min 1 di/dt Amps/μs max 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC < TJ < +150°C Thermal Considerations Package MS-012 8 7 6 Symbol TJ 5 Parameter Value -40 to +150 -65 to +150 120 Unit °C °C °C W 1 TS 2 3 4 0JA V-I Characteristics +I VF tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td VS VDRM -V VT +V 50 IDRM IH IS IT -I Half Value 0 0 tr td t – Time (μs) 106 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors SLIC Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of VS Change – % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 14 12 2.0 1.8 1.6 1.4 1.2 1.0 IH 25 °C 25°C Ratio of 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Case Temperature (TC) - ºC Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Reflow Condition - Temperature Min (Ts(min)) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) TL TS(max) Preheat tL Ramp-down +217°C 60-150 secs. TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 8 min. Max. +260°C 30 secs. Max. 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking (VDC JESD22-A-101 Physical Specifications Temp Cycling JESD22-A104 Biased Temp & Humidity High Temp Storage Low Temp Storage 52 VDC +150°C 1008 hrs. MIL-STD-750 (Method 1031) Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated classification 94V-0 Thermal Shock JESD22-A-106 Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 107 Fixed Voltage Enh. Single 0.8 SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-012 Inches MIN 0.053 0.004 0.043 0.012 0.007 0.189 0.228 0.150 0.016 MAX 0.069 0.010 0.065 0.020 0.010 0.197 0.244 0.157 0.050 Millimeters MIN 1.35 0.10 1.25 0.31 0.17 4.80 5.80 3.80 0.40 MAX 1.75 0.25 1.65 0.51 0.25 5.00 6.20 4.00 1.27 Dimension A A1 A2 o Recommended Soldering Pad Outline (Reference Only) Fixed Voltage Enh. Single C D E E1 e L Basic Spacing between Centers Part Numbering Part Marking P xxx 1 D F -1E TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE SINGLE ENHANCED IPP RATING PACKAGE TYPE XXXXXF1E o XXXXX Part Number Code (Refer to Electrical Characteristics Table) Date Code Packing Options Package Type D Pack Description MS-012 SMT 8-pin 2500 EIA-481-D Quantity Added Suffix Industry Standard Tape and Reel Specifications — MS-012 4.0 (.158) 8.0 (.315) 2.0 (.079) 1.55 (.061) DIMENSIONS ARE: MILLIMETERS (INCHES) 0.40 (0.016) 0.8 MIN. (0.03) 5.5 (.216) o 12.0 (.472) 6.4 (.252) 1.50 ø MIN. (.059) 0 MIN. 2.1 (.083) Cover Tape Carrier Tape Embossment Direction of Feed 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed 108 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.