P1500EBL

SIDACtor® Device RoHS TO-92 SIDACtor solid state protection devices protect telecommunications equipment such as modems, line cards, and CPE (telephones, answering machines, and fax machines). SIDACtor devices enable equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). . Electrical Parameters Part Number * P0080E_L P0300E_L P0640E_L P0720E_L P0900E_L P1100E_L P1300E_L P1500E_L P1800E_L P2300E_L P2600E_L P3100E_L P3500E_L VDRM Volts 6 25 58 65 75 90 120 140 170 190 220 275 320 VS Volts 25 40 77 88 98 130 160 180 220 260 300 350 400 VT Volts 4 4 4 4 4 4 4 4 4 4 4 4 4 IDRM µAmps 5 5 5 5 5 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 50 50 150 150 150 150 150 150 150 150 150 150 150 * “L” in part number indicates RoHS compliance. For non-RoHS compliant device, delete “L” from part number. For individual “EA”, “EB”, and “EC” surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. Surge Ratings in Amps IPP Series 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** Amps A B C 20 25 50 Amps 150 250 500 Amps 150 250 400 10x160 * 10x160 ** Amps 90 150 200 10x560 * 10x560 ** Amps 50 100 150 5x320 * 9x720 ** Amps 75 100 200 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz Amps 75 125 175 Amps 45 80 100 Amps 75 100 200 Amps 20 30 30 di/dt Amps/µs 500 500 500 * Current waveform in µs ** Voltage waveform in µs Telecom Design Guide • © 2006 Littelfuse 3 - 19 www.littelfuse.com SIDACtor Devices SIDACtor® Device Thermal Considerations Package TO-92 Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 90 Unit °C °C °C/W Capacitance Values pF Part Number * P0080E[A/B]L P0080ECL P0300E[A/B]L P0300ECL P0640E[A/B]L P0640ECL P0720EAL P0720EBL P0720ECL P0900EAL P0900EBL P0900ECL P1100EAL P1100EBL P1100ECL P1300EAL P1300EBL P1300ECL P1500EAL P1500EBL P1500ECL P1800EAL P1800EBL P1800ECL P2300EAL P2300EBL P2300ECL P2600EAL P2600EBL P2600ECL P3100EAL P3100EBL P3100ECL P3500EAL P3500EBL P3500ECL MIN 25 35 15 25 40 55 35 35 50 35 35 45 30 30 45 25 25 40 25 25 35 25 25 35 25 25 30 20 20 30 20 20 30 20 20 25 MAX 150 260 140 250 60 155 60 75 150 55 70 140 50 70 115 45 60 105 40 55 95 35 50 90 35 50 80 35 45 80 35 45 70 35 40 65 * [A/B] in part number indicates that values are for both A and B surge ratings. Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. www.littelfuse.com 3 - 20 © 2006 Littelfuse • Telecom Design Guide SIDACtor® Device +I IPP – Peak Pulse Current – %IPP tr = r ise time to peak value td = decay time to half value IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I V-I Characteristics tr x td Pulse Waveform Percent of VS Change – % 10 IH (TC = 25 ˚C) 14 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature Telecom Design Guide • © 2006 Littelfuse 3 - 21 www.littelfuse.com SIDACtor Devices