P1500SD

High Surge Current (D-rated) SIDACtor Device High Surge Current (D-rated) SIDACtor Device DO-214AA SIDACtor solid state protection devices with a D surge rating protect telecommunications equipment such as modems, line cards, fax machines, and other CPE. These SIDACtor devices withstand simultaneous surges incurred in GR 1089 lightning tests. (See "First Level Lightning Surge Test" on page 4-5.) Surge ratings are twice that of a device with a C surge rating. This allows a discrete surface mount version of Littelfuse’s patented “Y” configuration. (US Patent 4,905,119) SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * P0080SD ** P0300SD ** P0640SD ** P0720SD ** P0900SD ** P1100SD P1300SD P1500SD P1800SD P2300SD P2600SD P3100SD P3500SD VDRM Volts 6 25 58 65 75 90 120 140 170 190 220 275 320 VS Volts 25 40 77 88 98 130 160 180 220 260 300 350 400 VT Volts 4 4 4 4 4 4 4 4 4 4 4 4 4 IDRM µAmps 5 5 5 5 5 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 800 800 800 800 800 IT Amps *** 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 50 50 50 50 50 50 50 50 50 50 50 50 50 CO pF 200 220 100 100 100 80 80 80 60 60 60 60 60 * For surge ratings, see table below. ** Contact factory for release date. *** The 2.2 A version cannot be used to meet 4.4 A requirements. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 100 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. • Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias and is a typical value. Surge Ratings IPP 2x10 µs Amps 1000 IPP 8x20 µs Amps 800 IPP 10x160 µs Amps 400 IPP 10x560 µs Amps 300 IPP 10x1000 µs Amps 200 ITSM 60 Hz Amps 50 di/dt Amps/µs 1000 Series D http://www.littelfuse.com +1 972-580-7777 2 - 10 © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide High Surge Current (D-rated) SIDACtor Device Thermal Considerations Package DO-214AA Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 90 Unit °C °C °C/W +I +I IPP – Peak Pulse Current – %IPP tr = r ise time to peak value td = decay time to half value IT IT IS S IH IDRM -V -V VT VT VDRM VDRM VS V S 100 Peak Value Waveform = tr x td +V +V 50 Half Value 0 0 tr td t – Time (µs) -I -I V-I Characteristics tr x td Pulse Wave-form 14 Percent of VS Change – % 10 IH (TC = 25 ˚C) 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature © 2004 Littelfuse, Inc. SIDACtor® Data Book and Design Guide 2 - 11 http://www.littelfuse.com +1 972-580-7777 Data Sheets