P1803ACMCLXX

SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Balanced MC Series - Modified TO-220 Description Balanced MC Series Modified TO-220 are low capacitance SIDACtor® devices designed to protect broadband equipment from damaging overvoltage transients. The patented “Y” configuration also ensures balanced overvoltage protection. The series provides a single port solution that enables equipment to comply with various global requlatory standards while limiting the impact to broadband signals. Balance MC TO-220 Series Features and Benefits Agency Approvals Agency Agency File Number E133083 Low voltage overshoot Low on-state voltage Does not degrade with use Fails short circuit when surged in excess of ratings Balanced overvoltage protection 40% lower capacitance than our Baseband Protectors, for applications that demand greater signal integrity Robust Modified TO-220 Package Custom lead forms available Pinout Designation PIN 1 PIN 2 PIN 3 Applicable Global Standards TIA-968-A IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol 1 (T) ITU K.20/21 Enhanced Level 3 (R) ITU K.20/21 Basic GR 1089 Inter-building GR 1089 Intra-building 2 (G) Electrical Characteristics VDRM @lDRM=5μA V min P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx P1553ACMC P1803ACMC P2103ACMC P2353ACMC P2703ACMC P3203ACMC P3403ACMC P5103ACMC 130 150 170 200 230 270 300 420 VS @100V/μs V max 180 210 250 270 300 350 400 600 IH mA max Pins 1-2, 3-2, 1-3 150 150 150 150 150 150 150 150 IS mA max 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps V min 8 8 8 8 8 8 8 8 Part Number Marking Capacitance Pins 1-2, 3-2, 1-3 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack. Special order item -- contact factory.) 85 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Capacitance Values pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 30 55 30 60 30 45 25 45 25 40 25 40 20 35 20 30 pF Pin 1-3 Tip-Ring MIN MAX 20 35 15 30 15 30 15 30 15 30 15 30 15 25 10 20 Part Number P1553ACMCLxx P1803ACMCLxx P2103ACMCLxx P2353ACMCLxx P2703ACMCLxx P3203ACMCLxx P3403ACMCLxx P5103ACMCLxx Balance MC TO-220 Series Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series 0.2x310 0.5x700 2 A min C Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 2x10 2x10 2 A min 500 1 8x20 1.2x50 2 A min 400 1 10x160 10x160 2 A min 200 1 10x560 1 10x560 2 A min 150 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 ITSM 50/60 Hz A min 30 di/dt A/μs max 500 50 Thermal Considerations Package Modified TO-220 Symbol TJ TS PIN 1 PIN 2 PIN 3 Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 50 Unit °C °C °C/W R0JA V-I Characteristics +I tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) 86 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Normalized VS Change vs. Junction Temperature 14 12 10 Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change – % IH (TC = 25ºC) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 6 4 2 0 -4 -6 -8 -40 -20 0 IH 8 25 °C 25°C Balance MC TO-220 Series 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Ratio of Case Temperature (TC) - ºC Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pre Heat Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Figure 1 TP Ramp-up tP Critical Zone TL to TP TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) 3°C/sec. Max. +217°C 60-150 secs. +260(+0/-5)°C 30 secs. Max. 6°C/sec. Max. 8 min. Max. +260°C Temperature Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TL TS(max) Preheat tL Ramp-down TS(min) tS 25 time to peak temperature (t 25ºC to peak) Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed Time Physical Specifications Environmental Specifications 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/ JEDEC, JESD22-A-102 +260°C, 30 secs. MIL-STD-750 (Method 2031) 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated High Temp Voltage Blocking Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level 87 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Part Numbering P xxx 3 A C MC L xx TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS Blank, RP or 60 -for Type 60 orders, contact factory Part Marking XXXXXXXXX Part Marking Code (Refer to Electrical Characteristics Table) xxxxx Date Code RoHS COMPLIANT MC Series IPP RATING Balance MC TO-220 Series Dimensions - Modified TO-220 A O Tape and Reel Specification — Modified TO-220 Inches Min Max 0.410 0.375 0.130 0.575 0.035 0.205 0.105 0.075 0.085 0.024 0.188 0.310 Millimeters Min 9.14 2.80 0.63 4.95 2.41 1.52 1.78 0.46 4.52 7 .37 Max 1.626 (41.15) 0.240 (6.10) 0.019 (0.5) 0.750 ± 0.010 (19.05 ± 0.25) 0.360 (9.14) 0.500 (12.7) D A F Temperature Measurement Point P PIN 3 PIN 2 PIN 1 L K H J M N 0.400 0.360 0.110 0.540 0.025 0.195 0.095 0.060 0.070 0.018 0.178 0.290 10.16 10.42 9.53 3.30 0.89 5.21 2.67 1.90 2.16 0.61 4.78 7 .87 D F G H J K L M 0.720 (18.29) G 13.71 14.61 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. N O P 1.968 (50.0) Packing Options Package Type Description Modified TO-220 Tape and Reel Pack A Modified TO-220 Bulk Pack Modified TO-220, Type 60 Lead Form Bulk Pack Quantity 700 500 500 Added Suffix RP N/A 60 (special order item, contact factory for details) Industry Standard EIA-468-B N/A N/A 88 © 2010 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.