P3002GBLRP

SIDACtor ® Protection Thyristors Broadband Optimized™ Protection TwinChip™ Series - DO-15 Description TwinChip™ Series DO-15 are very low capacitance SIDACtor® devices designed to protect broadband CPE equipment, such as VoIP and xDSL modems from damaging overvoltage transients. The series provides a through-hole solution that enables equipment to comply with global regulatory standards while limiting the impact to broadband signals. Features & Benefits Agency Approvals Agency Agency File Number E133083 surged in excess of ratings footprint Applicable Global Standards Pinout Designation NOT APPLICABLE Schematic Symbol Electrical Characteristics VDRM@ IDRM=5μA V min P2602GALRP P3002GALRP P3502GALRP P2602GBLRP P3002GBLRP P3502GBLRP P262A P30A P352A P262B P30B P352B 220 280 320 220 280 320 VS@ 100V/μs V max 300 360 400 300 360 400 VT @ IT = 2.2 Amps V max 8 8 8 8 8 8 Capacitance @1MHz @ 2V bias pF min 15 10 10 15 10 10 pF max 25 20 20 25 20 20 Part Number Marking IH mA min 150 150 150 150 150 150 IS mA max 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 49 TwinChip Series SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Surge Ratings IPP Series A B 10x560μs A min 50 100 10x1000μs A min 50 80 ITSM 50 / 60 Hz A min 20 25 TwinChip Series Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Symbol TJ TS DO-15 Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C R0JA 120 °C/W V-I Characteristics tr x td Pulse Waveform +I IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of VS Change – % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 14 12 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Ratio of Junction Temperature (TJ) – °C Case Temperature (TC) - ºC 50 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters Pb-Free assembly (see Figure 1) 150°C 200°C 60-180 secs 3°C/second max 3°C/second max 217°C 60-150 seconds Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Figure 1 TP Ramp-up tP Critical Zone TL to TP Temperature TL TS(max) Preheat tL Ramp-down TS(min) tS 25 time to peak temperature (t 25ºC to peak) Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed 30 seconds max 6°C/second max 8 minutes max 260°C Time Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/ JEDEC, JESD22-A104 52 VDC EIA/JEDEC, JESD22-A-101 1031) JEDEC, JESD22-A-101 -65°C, 1008 hrs. Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Temp Cycling Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level EIA/JEDEC, JESD22-A-102 2031) © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 51 TwinChip Series SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Dimensions — DO-15 Dimension B Inches min 0.028 0.12 0.235 1 max 0.034 0.14 0.27 Millimeters min 0.711 3.048 5.969 25.4 max 0.864 3.556 6.858 D B D L G L G L TwinChip Series Part Numbering Part Marking P xxx 2 G x L RP RoHS COMPLIANT IPP RATING Part Marking Code (Refer to Electrical Characteristics Table) MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE Pxxxx XXXXX TYPE P = SIDACtor REEL PACK Date Code Packing Options Package Type G Description DO-15 Axial Tape & Reel Quantity 5000 Added Suffix RP Industry Standard EIA-RS-296-D Tape and Reel Specification — DO-15 Symbols Spacing off center, either side 0.039 (1.0) Description Component Spacing (lead to lead) Inner Tape Pitch Tape Width Max. Off Alignment Reel Dimension Max. Hub Recess Max. Abor Hole inch mm 5.08 ± 0.508 52.37 ± 1.498 6.35 1.219 330.2 76.19 17 .27 B 2.55 (64.8) TYP A B C D E F G A C D E Dimensions are in inches (and millimeters). 3.15 (80.0) TYP recess depth max 0.75” G F Direction of Feed 52 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.