P3100Q12ALRP

SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Q2L Series - 3x3 QFN Description Q2L Series 3x3 QFN are low capacitance SIDACtor® devices designed to protect high density broadband equipment from damaging overvoltage transients. The series provides a low profile, chip scale surface mount solution that enables broadband equipment to comply with global regulatory standards while limiting the impact to broadband signals and board space. Features and Benefits Agency Approvals Agency Agency File Number E133083 surged in excess of ratings Pinout Designation Not Applicable Schematic Symbol Applicable Global Standards Level* * A/B-Rated parts require series resistance Electrical Characteristics VDRM Part Number P0080Q12ALRP P0300Q12ALRP P0640Q12ALRP P0720Q12ALRP P0900Q12ALRP P1100Q12ALRP P1300Q12ALRP P1500Q12ALRP P1800Q12ALRP P2300Q12ALRP P2600Q12ALRP P3100Q12ALRP P3500Q12ALRP Marking P-8A P03A P06A P07A P09A P11A P13A P15A P18A P23A P26A P31A P35A @lDRM=5μA V min 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/μs V max 25 40 77 88 98 130 160 180 220 260 300 350 400 VT@ IT = 2.2Amps V max 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, 2V bias pF min pF max 25 15 40 40 35 30 25 25 25 25 25 20 20 55 35 60 60 55 50 45 40 35 35 35 35 30 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). Table continues on next page. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 58 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Electrical Characteristics (continued) VDRM Part Number Marking @lDRM=5μA V min P0080Q12BLRP P0300Q12BLRP P0640Q12BLRP P0720Q12BLRP P0900Q12BLRP P1100Q12BLRP P1300Q12BLRP P1500Q12BLRP P1800Q12BLRP P2300Q12BLRP P2600Q12BLRP P3100Q12BLRP P3500Q12BLRP P-8B P03B P06B P07B P09B P11B P13B P15B P18B P23B P26B P31B P35B 6 25 58 65 75 90 120 140 170 190 220 275 320 VS @100V/μs V max 25 40 77 88 98 130 160 180 220 260 300 350 400 IH IS IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT@ IT = 2.2Amps V max 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, 2V bias pF min pF max 25 15 40 40 35 30 25 25 25 25 25 20 20 55 35 60 60 55 50 45 40 35 35 35 35 30 mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). Surge Ratings Ipp Series A B 2x10μs A min 150 250 1.2x50μs/8x20μs A min 150 250 10x160μs A min 90 150 10x560μs A min 50 100 10x1000μs A min 45 80 ITSM 50 / 60 Hz A min 20 25 A/μs max 500 500 di/dt Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package 3x3 QFN Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 120 °C/W © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 59 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection V-I Characteristics tr x td Pulse Waveform +I IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of VS Change – % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 14 12 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Ratio of Junction Temperature (TJ) – °C Case Temperature (TC) - ºC Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 60 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Physical Specifications Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Resistance to Solder Heat Moisture Sensitivity Level Dimensions — 3x3 QFN BOTTOM VIEW C J E TOP VIEW A Dimensions A B C E F H J K1 K2 M1 M2 N1 N2 Inches Min 0.114 0.114 0.075 0.011 0.076 0.035 0.000 0.004 0.004 0.056 0.038 0.096 0.082 Max 0.122 0.122 0.083 0.019 0.084 0.043 0.008 0.012 0.012 0.064 0.046 0.104 0.090 Millimeters Min 2.900 2.900 1.900 0.285 1.930 0.900 0.000 0.100 0.100 1.430 0.970 2.440 2.080 Max 3.100 3.100 2.100 0.485 2.130 1.100 0.200 0.300 0.300 1.630 1.170 2.640 2.280 B F END VIEW H SIDE VIEW 1.50 (.059”) 1.27 (.050”) 2.54 (.100”) N2 N1 K1 M1 M2 K2 Recommended Soldering Pad Outline (Reference Only) Part Numbering P xxx 0 Q12 x L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE REEL PACK RoHS COMPLIANT IPP RATING Part Marking Terminals on Back XXXX XXXXX Part Marking Code Date code (Refer to Electrical Characteristics Table) Packing Options Package Type Q12 Description 3x3 QFN Tape and Reel Pack Quantity 5000 Added Suffix RP Industry Standard EIA-481-D © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 61 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Tape and Reel Dimensions — 3x3 QFN Reel Dimension Symbols Description Reel Diameter Drive Spoke Width Arbor Hole Diameter Drive Spoke Diameter Hub Diameter Reel Inner Width at Hub Pocket Width at bottom Pocket Length at bottom Feed Hole Diameter Pocket Hole Diameter Feed hole position 1 Feed hole position 2 Feed hole center-Pocket hole Pocket Depth Feed Hole Pitch Component Spacing Feed hole center-Pocket hole Carrier Tape Thickness Embossed Carrier Tape Width Cover Tape Width Inches Min N/A 0.059 0.504 0.795 1.969 0.488 0.126 0.126 0.059 0.059 0.065 0.400 0.215 0.039 0.153 0.311 0.077 0.010 0.453 0.358 Max 12.992 N/A 0.531 N/A N/A 0.567 0.134 0.134 0.063 N/A 0.073 0.408 0.219 0.051 0.161 0.319 0.081 0.014 0.484 0.366 Millimeters Min N/A 1.50 12.80 20.20 50.00 12.40 3.20 3.20 1.50 1.50 1.65 10.15 5.45 1.00 3.90 7.90 1.95 0.25 11.50 9.10 Max 330.0 N/A 13.50 N/A N/A 14.40 3.40 3.40 1.60 N/A 1.85 10.35 5.55 1.30 4.10 8.10 2.05 0.35 12.30 9.30 C A D B W1 N Tape Leader and Trailer Dimensions END CARRIER TAPE COVER TAPE START A B C D N W1 A0 B0 D0 D1 E1 E2 F TRAILER 160mm MIN LEADER 400mm MIN Tape Dimension Items K0 P0 P1 D0 T P0 P2 CARRIER TAPE D1 E1 P2 T W0 K0 COVER TAPE B0 F E2 W P1 A0 W W0 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 62 Revised: February 22, 2011