P3403UBLXX

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Balanced Series - MS-013 Description The SIDACtor® Balanced Series MS-013 are designed to protect baseband equipment from overvoltage transients. overvoltage protection. The series provides a single port surface mount solution that enables voice through DS-1 equipment to comply with various global requlatory standards. Features and Benefits Balanced overvoltage protection Low voltage overshoot Agency Agency File Number E133083 Agency Approvals Fails short circuit when surged in excess of ratings Replaces three discrete devices Meets UL/IEC 60950-1 creepage and clearance Low on-state voltage Does not degrade with use Pinout Designation 1 2 3 6 5 4 Applicable Global Standards TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol 1 2 3 6 5 4 Electrical Characteristics VDRM @lDRM=5μA VS @100V/μs VDRM @lDRM=5μA VS @100V/μs VT V max 8 8 8 8 8 8 8 8 IS mA max 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH Capacitance mA min 150 150 150 150 150 150 150 150 Part Number Part Marking V min V max V min V max Pins 1 & 6-3, 1 & 6-4 P1553UALxx P1803UALxx P2103UALxx P2353UALxx P2703UALxx P3203UALxx P3403UALxx P5103UALxx P1553UA P1803UA P2103UA P2353UA P2703UA P3203UA P3403UA P5103UA 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 130 150 170 200 230 270 300 420 Pins 3-4 180 210 250 270 300 350 400 600 See Capacitance Values table Table continues on next page. Notes: - Absolute maximum ratings measured at TA - Devices are bi-directional. - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 148 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) VDRM @lDRM=5μA VS @100V/μs VDRM @lDRM=5μA VS @100V/μs VT V max 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 IS mA max 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 IT A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH Capacitance mA min 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 Part Number Part Marking V min V max V min V max Pins 1 & 6-3, 1 & 6-4 P1553UBLxx P1803UBLxx P2103UBLxx P2353UBLxx P2703UBLxx P3203UBLxx P3403UBLxx P5103UBLxx P1553UCLxx P1803UCLxx P2103UCLxx P2353UCLxx P2703UCLxx P3203UCLxx P3403UCLxx P5103UCLxx P1553UB P1803UB P2103UB P2353UB P2703UB P3203UB P3403UB P5103UB P1553UC P1803UC P2103UC P2353UC P2703UC P3203UC P3403UC P5103UC 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 130 150 170 200 230 270 300 420 130 150 170 200 230 270 300 420 Pins 3-4 180 210 250 270 300 350 400 600 180 210 250 270 300 350 400 600 See Capacitance Values table Capacitance Values Pin 3-4 Tip-Ring pF min 20 20 15 15 15 15 15 10 25 25 20 20 20 20 15 15 30 30 30 25 25 25 20 20 pF max 95 85 85 75 75 70 65 60 95 85 85 75 75 70 65 60 95 85 85 75 75 70 65 60 Pins 1 & 6-3, 1 & 6-4 Tip-Ground, Ring-Ground pF min 10 10 10 10 10 10 10 10 15 15 15 15 10 10 10 10 20 15 15 15 15 15 15 10 pF max 60 55 55 50 50 45 45 40 60 55 55 50 50 45 45 40 60 55 55 50 50 45 45 40 Part Number P1553UALxx P1803UALxx P2103UALxx P2353UALxx P2703UALxx P3203UALxx P3403UALxx P5103UALxx P1553UBLxx P1803UBLxx P2103UBLxx P2353UBLxx P2703UBLxx P3203UBLxx P3403UBLxx P5103UBLxx P1553UCLxx P1803UCLxx P2103UCLxx P2353UCLxx P2703UCLxx P3203UCLxx P3403UCLxx P5103UCLxx Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 149 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings IPP Series 0.2x310 1 0.5x700 2 A min A B C Notes: 1 Current waveform in μs 2 Voltage waveform in μs 2x10 1 2x10 2 A min 150 250 500 8x20 1 1.2x50 2 A min 150 250 400 10x160 1 10x160 2 A min 90 150 200 10x560 1 10x560 2 A min 50 100 150 5x320 1 9x720 2 A min 75 100 200 10x360 1 10x360 2 A min 75 125 175 10x1000 1 10x1000 2 A min 45 80 100 5x310 1 10x700 2 A min 75 100 200 ITSM 50/60 Hz A min 20 25 50 di/dt A/ μs max 500 500 500 20 25 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Modified MS-013 6 5 4 1 2 3 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 60 °C/W V-I Characteristics +I tr x td Pulse Waveform IT IS IH IDRM -V VT VDRM VS +V IPP – Peak Pulse Current – %IPP 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (μs) -I Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature Percent of VS Change – % 10 IH (TC = 25ºC) 14 12 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 -40 -20 0 20 40 60 80 100 120 140 160 6 4 2 0 -4 -6 -8 IH 8 25 °C 25°C Ratio of Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Case Temperature (TC) - ºC 150 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Part Marking XXXXXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Packing Options P xxx 3 U x L xx TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE PACKING OPTIONS RP: Reel Pack TP: Tube Pack Package Type Description Quantity Added Suffix Industry Standard RoHS COMPLIANT IPP RATING U Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 500 6-pin Tube Pack (50 per tube) TP N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 151 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions — MS-013 Dimensions Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters). Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 0.143 Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 3.63 7º TYP A D 7º TYP G A J H Burr Side 96º 4º 7º TYP B A F 7º TYP MIN Length of Flat K Detail A Mold Split Line BSC* A B C D E F G H J K BSC* * BSC = Basic Spacing between Centers Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .512 (13.0) Arbor Hole Dia. .472 (12.0) 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .110 (2.79) .045 (1.14) 90˚ .165 (4.19) .310 (7.87) 6 Interior of the Tube 20.000 ± .030 (508.00 ± 0.76) .005 A .150 (3.81) .225 (5.72) .525 (13.34) A Dimensions are in inches (and millimeters) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 152 Revised: February 22, 2011