P3602ABLXX

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - Modified TO-220 Description The SIDACtor® Series Modified TO-220 are designed to protect baseband equipment from damaging overvoltage transients. The series provides a robust single port through-hole solution that enables voice though DS-1 equipment to comply with various global regulatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Does not degrade with use Modified TO-220 Package Applicable Global Standards Fails short circuit when surged in excess of ratings Single-port protection Lead forms available Pinout Designation Level* PIN 1 PIN 2 PIN 3 *A/B-rated parts require series resistance Schematic Symbol 1 (T) 3 (R) 2 (G) Electrical Characteristics VDRM VS VDRM VS @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs Part Number Marking V min V max V min V max Pins 1-3 VT @IT=2.2 A V max Pins 1-2, 3-2 IH mA min IS mA max IT Capacitance @1MHz, 2V bias Pins 1-2, 3-2 A pF min pf max max P0602AALxx P1402AALxx P1602AALxx P2202AALxx P2702AALxx P3002AALxx P3602AALxx P4202AALxx P4802AALxx P6002AALxx P0602AA P1402AA P1602AA P2202AA P2702AA P3002AA P3602AA P4202AA P4802AA P6002AA 25 58 65 90 120 140 170 190 220 275 40 77 95 130 160 180 220 250 300 350 50 116 130 180 240 280 340 380 440 550 80 154 190 260 320 360 440 500 600 700 4 4 4 4 4 4 4 4 4 4 50 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 See Capacitance Values Table 2.2 2.2 2.2 2.2 2.2 Table continues on next page. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 166 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Electrical Characteristics (continued) VDRM VS VDRM VS @lDRM=5μA @100V/μs @lDRM=5μA @100V/μs V min 25 58 65 90 120 140 170 190 220 275 25 58 65 90 120 140 170 190 220 275 V max 40 77 95 130 160 180 220 250 300 350 40 77 95 130 160 180 220 250 300 350 V min 50 116 130 180 240 280 340 380 440 550 50 116 130 180 240 280 340 380 440 550 V max 80 154 190 260 320 360 440 500 600 700 80 154 190 260 320 360 440 500 600 700 Pins 1-2, 3-2 Pins 1-3 Part Number Marking VT @IT=2.2 A V max Pins 1-2, 3-2 IH mA min IS mA max IT A max Capacitance P0602ABLxx P1402ABLxx P1602ABLxx P2202ABLxx P2702ABLxx P3002ABLxx P3602ABLxx P4202ABLxx P4802ABLxx P6002ABLxx P0602ACLxx P1402ACLxx P1602ACLxx P2202ACLxx P2702ACLxx P3002ACLxx P3602ACLxx P4202ACLxx P4802ACLxx P6002ACLxx P0602AB P1402AB P1602AB P2202AB P2702AB P3002AB P3602AB P4202AB P4802AB P6002AB P0602AC P1402AC P1602AC P2202AC P2702AC P3002AC P3602AC P4202AC P4802AC P6002AC 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 50 150 150 150 150 150 150 150 150 150 50 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 See Capacitance Values Table Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form bulk pack) Capacitance Values pF Pin 1-2, 3-2 Tip-Ground, Ring-Ground MIN MAX 15 145 40 60 35 60 30 50 25 45 25 40 25 35 25 35 20 35 20 35 15 250 40 155 35 145 30 115 25 105 25 95 25 90 25 85 20 85 20 80 pF Pin 1-3 Tip-Ring MIN MAX 10 90 20 35 20 35 15 30 15 25 15 25 10 20 10 20 10 20 10 20 10 145 20 90 20 85 15 65 15 60 15 55 10 50 10 50 10 50 10 45 pF Pin 1-2, 3-2 Tip-Ground, Ring-Ground MIN P0602ACLxx P1402ACLxx P1602ACLxx P2202ACLxx P2702ACLxx P3002ACLxx P3602ACLxx P4202ACLxx P4802ACLxx P6002ACLxx 25 55 45 45 40 35 35 30 30 30 MAX 250 155 145 115 105 95 90 85 85 80 10 30 25 25 20 20 15 15 15 15 pF Pin 1-3 Tip-Ring MIN MAX 145 90 85 65 60 55 50 50 50 45 Part Number P0602AALxx P1402AALxx P1602AALxx P2202AALxx P2702AALxx P3002AALxx P3602AALxx P4202AALxx P4802AALxx P6002AALxx P0602ABLxx P1402ABLxx P1602ABLxx P2202ABLxx P2702ABLxx P3002ABLxx P3602ABLxx P4202ABLxx P4802ABLxx P6002ABLxx Part Number Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 167 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings IPP Series 0.2x310 0.5x700 2 1 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 50 100 150 5x320 1 9x720 2 A min 75 100 200 10x360 1 10x360 2 A min 75 125 175 10x1000 1 10x1000 2 A min 45 80 100 5x310 1 10x700 2 A min 75 100 200 ITSM 50/60 Hz A min 20 25 50 di/dt A/μs max 500 500 500 A min A B C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 150 250 500 A min 150 250 400 A min 90 150 200 20 25 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Modified TO-220 Symbol TJ TS PIN 1 PIN 2 PIN 3 Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C R0JA 60 °C/W V-I Characteristics +I tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 Percent of VS Change – % 10 IH (TC = 25ºC) 14 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 6 4 2 0 -4 -6 -8 -40 -20 0 IH 8 25 °C 25°C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Ratio of Case Temperature (TC) - ºC © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 168 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering Part Marking XXXXXXXXX P xxx 2 A x L xx TYPE P = SIDACtor Part Marking Code (Refer to Electrical Characteristics Table) PACKING OPTIONS Blank: Bulk RP: Reel Pack 60: Type 60 Lead Form (Special order item. For type 60 orders, contact factory) xxxxx Date Code MEDIAN VOLTAGE CONSTRUCTION VARIABLE PACKAGE TYPE RoHS COMPLIANT IPP RATING © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 169 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Dimensions - Modified TO-220 A O Tape and Reel Specification — Modified TO-220 Inches Min Max 0.410 0.375 0.130 0.575 0.035 0.205 0.105 0.075 0.085 0.024 0.188 0.310 Millimeters Min 9.14 2.80 0.63 4.95 2.41 1.52 1.78 0.46 4.52 7 .37 Max 1.626 (41.15) 0.240 (6.10) 0.019 (0.5) 0.750 ± 0.010 (19.05 ± 0.25) 0.360 (9.14) 0.500 (12.7) D A F Temperature Measurement Point P PIN 3 PIN 2 PIN 1 L K H J M N 0.400 0.360 0.110 0.540 0.025 0.195 0.095 0.060 0.070 0.018 0.178 0.290 10.16 10.42 9.53 3.30 0.89 5.21 2.67 1.90 2.16 0.61 4.78 7 .87 D F G H J K L M 0.720 (18.29) G 13.71 14.61 0.100 (2.54) 0.100 (2.54) 14.173 (360.0) Dimensions are in inches (and millimeters). Direction of Feed The modified TO-220 package is designed to meet mechanical standards as set forth in JEDEC publication number 95. N O P 1.968 (50.0) Packing Options Package Type Description Modified TO-220 Tape and Reel Pack A Modified TO-220 Bulk Pack Modified TO-220 Type 60 Lead Form Bulk Pack Quantity 700 500 Added Suffix RP N/A 60 (special order item, contact factory for details) Industry Standard EIA-468-B N/A 500 N/A © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 170 Revised: February 22, 2011