QXX25RH5TP

Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Qxx25xx & Qxx25xHx Series Description ® 25 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. Alternistor type devices only operate in quadrants I, II, & III and are used in circuits requiring high dv/dt capability. Features & Benefits to 250 A Agency Approval Agency ® junctions Agency File Number TO-220L, TO-218K, TO-218J & Fastpak Packages: E71639 to 1000 V Applications Excellent for AC switching and phase control applications such as heating, lighting, and motor speed controls. Main Features Symbol IT(RMS) VDRM /VRRM IGT Value 25 1000 50 to 80 Unit A V mA Typical applications are AC solid-state switches, industrial power tools, exercise equipment, white goods and commercial appliances. Alternistor Triacs (no snubber required) are used in applications with extremely inductive loads requiring highest commutation performance. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Schematic Symbol MT2 MT1 G ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 117 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs Standard type devices normally operate in Quadrants I & III triggered from AC line. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Absolute Maximum Ratings – Standard Triac Symbol IT(RMS) Parameter RMS on-state current Qxx25R5 Qxx25N5 Qxx25P5 Qxx25R5 Qxx25N5 ITSM Peak non-repetitive surge current Qxx25P5 Test Conditions TC = 85°C TC = 57°C single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C tp = 8.3ms f = 60Hz; TJ =125°C TJ = 125°C TJ = 125°C Qxx25R5 Qxx25N5 Qxx25P5 167 200 A 220 250 166 260 100 2 0.5 -40 to 125 -40 to 125 -25 to 125 A/μs A W °C °C Value 25 Unit A I 2t di/dt IGTM PG(AV) Tstg TJ I2t Value for fusing Critical rate-of-rise of on-state current Peak gate current Average gate power dissipation Storage temperature range Operating junction temperature range Qxx25R5 Qxx25N5 Qxx25P5 A2s Absolute Maximum Ratings – Alternistor Triac Symbol Parameter Qxx25LH5 Qxx25L6 Qxx25K6 Qxx25J6 Qxx25RH5 Qxx25NH5 Qxx25R6 Qxx25NH6 Test Conditions TC = 65°C TC = 85°C 25 TC = 95°C A Value Unit IT(RMS) RMS on-state current ITSM Peak non-repetitive surge current single half cycle; f = 50Hz; TJ (initial) = 25°C single half cycle; f = 60Hz; TJ (initial) = 25°C tp = 8.3ms f = 60Hz; TJ =125°C TJ = 125°C TJ = 125°C 208 A 250 260 100 2 0.5 -40 to 125 -40 to 125 A2s A/μs A W °C °C I 2t di/dt IGTM PG(AV) Tstg TJ Note: xx = voltage I2t Value for fusing Critical rate-of-rise of on-state current Peak gate current Average gate power dissipation Storage temperature range Operating junction temperature range Qxx25xx & Qxx25xHx Series 118 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Standard Triac Value Symbol Test Conditions Quadrant I – II – III VD = 12V; RL = 60 VGT VGD IH VD = VDRM; RL = 3.3 k IT = 400mA (initial) VD = VDRM; Gate Open; TJ = 125°C VD = VDRM; Gate Open; TJ = 100°C (dv/dt)c tgt (di/dt)c = 13.3 A/ms; TJ = 125°C IG = 2 x IGT; PW = 15μs; IT = 35.4 A 400V 600V 800V 1000V MIN. TYP . 4 ; TJ = 125°C IV I – II – III IV ALL MAX. TYP . MAX. TYP . MIN. MAX. 100 275 225 200 200 5 3 Qxx25R5 Qxx25N5 50 120 1.3 2.5 0.2 50 — 475 400 — V/μs μs Qxx25P5 Unit IGT mA V V mA dv/dt MIN. V/μs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Alternistor Triac Value Symbol Test Conditions Quadrant Qxx25RH5 Qxx25LH5 Qxx25NH5 MAX. MAX. MIN. MAX. 400V 600V 800V 1000V MIN. TYP . 50 575 500 400 — 20 3 50 1.3 0.2 100 600 600 475 400 30 5 V/μs μs Qxx25R6 Qxx25L6 Qxx25NH6 Qxx25K6 Qxx25J6 80 Unit IGT VGT VGD IH VD = 12V; RL = 60 VD = VDRM; RL = 3.3 k IT = 400mA (initial) VD = VDRM; Gate Open; TJ = 125°C VD = VDRM; Gate Open; TJ = 100°C ; TJ = 125°C I – II – III I – II – III I – II – III mA V V mA dv/dt MIN. V/μs (dv/dt)c tgt (di/dt)c = 13.3 A/ms; TJ = 125°C IG = 2 x IGT; PW = 15μs; IT = 35.4 A Static Characteristics Value Qxx25R5 Qxx25N5 Qxx25xH5 Qxx25P5 Qxx25x6 Qxx25NH6 MAX. TJ = 25°C IDRM / IRRM VDRM / VRRM TJ = 100°C TJ = 125°C Note: xx = voltage, x = package ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 119 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series Symbol Test Conditions Unit VTM IT = 35.4A; tp = 380 μs 600 – 800V 1000V 600 – 800V 1000V 600 – 800V 1.8 10 20 1.4 100 — — — 5000 V MAX. 500 1000 2000 μA 25 A TRIACs Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Thermal Resistances Symbol Parameter Qxx25R5 / Qxx25N5 Qxx25R6 / Qxx25NH6 Qxx25RH5 / Qxx25NH5 R (J-C) Value 0.89 1.6 2.0 1.32 45 Unit Junction to case (AC) Qxx25P5 Qxx25L6 / Qxx25LH5 Qxx25K6 / Qxx25J6 Qxx25Ry °C/W R (J-A) Junction to ambient Qxx25L6 / Qxx25LH5 50 °C/W Note: xx = voltage, y = sensitivity Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature 2. 5 Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 2.0 Ratio of VGT / VGT(TJ = 25ºC) Ratio of IGT/IGT(TJ = 25°C) 1.5 1. 5 1.0 1.0 0.5 0. 5 0.0 -40 -15 10 35 60 85 110 125 0.0 -40 -15 10 35 60 85 110 125 Junction Temperature (TJ) -- (°C) Junction Temperature (TJ) -- (ºC) Figure 3: Normalized DC Holding Current vs. Junction Temperature 2.0 Figure 4: On-State Current vs. On-State Voltage (Typical) 90 Instantaneous On-state Current (iT) – Amps TJ = 25°C 80 70 60 50 40 30 20 10 0 Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 Ratio of IH / IH(TJ = 25ºC) 1. 5 1.0 0. 5 Qxx25R5 Qxx25N5 0.0 -40 -15 10 35 60 85 110 125 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Junction Temperature (TJ) -- (ºC) Instantaneous On-state Voltage (vT) – Volts Qxx25xx & Qxx25xHx Series 120 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 35 Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current 130 Average On-State Power Dissipation [PD(AV)] -- Watts 30 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° Qxx25R5 Qxx25N5 Maximum Allowable Case Temperature (TC) - °C 120 110 100 90 80 Qxx25P5 70 60 50 Qxx25R6 Qxx25NH6 Qxx25RH5 Qxx25NH5 25 Qxx25R5 Qxx25N5 Qxx25K6 Qxx25J6 20 15 Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 10 5 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 0 5 10 15 20 25 30 0 0 5 10 15 20 25 RMS On-State Current [IT(RMS)] -- Amps RMS On-State Current [IT(RMS)] - Amps Figure 7: Maximum Allowable Ambient Temperature vs. RMS On-State Current (TO-220 packages only) 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° FREE AIR RATING Maximum Allowable Ambient Temperature (TA) --°C 100 80 60 40 20 0 0.0 0.5 1.0 1.5 2.0 2.5 RMS On-State Current [IT(RMS)] -- Amps Figure 8: Surge Peak On-State Current vs. Number of Cycles 1000 Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps Qxx25P5/Qxx25R6 Qxx25L6/Qxx25NH6 Qxx25K6/Qxx25J6 Qxx25RH5/Qxx25LH5 Qxx25NH5 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 100 Qxx25R5 Qxx25N5 10 1 10 100 1000 Surge Current Duration -- Full Cycles ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 121 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs Qxx25L6 Qxx25LH5 Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Pb – Free assembly TP Temperature Ramp-up tP 150°C 200°C 60 – 180 secs 5°C/second max 5°C/second max 217°C 60 – 150 seconds 260+0/-5 °C 20 – 40 seconds 5°C/second max 8 minutes Max. 280°C TL TS(max) Preheat Preheat tL Ramp-do Ramp-down TS(min) tS 25 time to peak temperature Time Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed Physical Specifications Terminal Finish 100% Matte Tin-plated UL recognized epoxy meeting flammability classification 94V-0 Copper Alloy Environmental Specifications Test High Temperature Voltage Blocking Temperature Cycling Biased Temp & Humidity High Temp. Storage Specifications and Conditions MIL -STD-750: Method 1040, Condition A Rated VRRM, 125°C, 1008 hours MIL -STD-750: Method 1051 -40°C to 125°C, 15-minute dwell, 100 cycles EIA/JEDEC: JESD22-A101 320VDC, 85°C, 85%RH, 1008 hours MIL -STD-750: Method 1031 150°C, 1008 hours -40°C, 1008 hours MIL -STD-750: Method 1056 0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles Body Material Lead Material Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage Thermal Shock Autoclave EIA/JEDEC: JESD22-A102 (Pressure Cooker Test) 121°C, 100%RH, 2atm, 168 hours Resistance to Solder Heat Solderability Lead Bend MIL -STD-750: Method 2031 260°C, 10 seconds ANSI/J-STD-002, Category 3, Test A MIL -STD-750: Method 2036, Condition E Qxx25xx & Qxx25xHx Series 122 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-220AB (R Package) — Non-isolated Mounting Tab TC MEASURING POINT O ØE A MT2 B C D 7.01 .276 13.36 .526 P 8.13 .320 AREA (REF.) 0.17 IN2 Dimension A B C D Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048 Millimeters Min 9.65 2.67 5.84 14.99 3.61 2.79 13.72 0.64 4.95 2.41 1.52 2.16 0.46 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 F G L H R NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F G H 3.30 14.61 0.89 5.21 2.67 1.91 2.41 0.61 4.78 1.52 1.22 K J MT1 MT2 GATE N M J Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). K L M N O P R Dimensions — TO-220AB (L Package) — Isolated Mounting Tab TC MEASURING POINT O ØE A P 8.13 .320 AREA (REF.) 0.17 IN2 Dimension A 13.36 .526 7.01 .276 Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048 Millimeters Min 9.65 2.66 5.85 14.98 3.61 2.80 13.71 0.63 4.95 2.41 1.52 1.78 0.45 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 3.73 3.30 14.60 0.89 5.21 2.67 1.91 2.16 0.61 4.78 1.53 1.22 B C D B C D E F F G L H R G H J K J MT1 MT2 GATE N M Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). K L M N O P R ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 123 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs E 3.73 Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-263 (N Package) — D2Pak Surface Mount TC MEASURING POINT B MT2 V C E AREA: 0.11 IN2 Dimension 8.41 .331 Inches Min 0.360 0.380 0.178 0.025 0.045 0.060 0.095 0.092 0.018 0.090 0.590 0.035 0.002 0.040 Millimeters Max 0.370 0.420 0.188 0.035 0.060 0.075 0.105 0.102 0.024 0.110 0.625 0.045 0.010 0.070 Min 9.14 9.65 4.52 0.64 1.14 1.52 2.41 2.34 0.46 2.29 14.99 0.89 0.05 1.02 Max 9.40 10.67 4.78 0.89 1.52 1.91 2.67 2.59 0.61 2.79 15.88 1.14 0.25 1.78 A S 7.01 .276 A B C W U GATE G D F H K J D E 8.13 .320 MT1 F G 11.68 .460 2.16 .085 H J 7.01 .276 16.89 .665 8.89 .350 7.01 .276 K S V U 1.40 .055 3.81 .150 2.03 .080 6.60 .260 W Dimensions — TO-218AC (K Package) — Isolated Mounting Tab TC Measurement Point B U (diameter) C D Dimension A Inches Min 0.810 0.610 0.178 0.055 0.487 0.635 0.022 0.075 0.575 0.211 0.422 0.058 0.045 0.095 0.008 0.008 0.164 0.085 Max 0.835 0.630 0.188 0.070 0.497 0.655 0.029 0.095 0.625 0.219 0.437 0.068 0.055 0.115 0.016 0.016 0.165 0.095 Millimeters Min 20.57 15.49 4.52 1.40 12.37 16.13 0.56 1.91 14.61 5.36 10.72 1.47 1.14 2.41 0.20 0.20 4.10 2.17 Max 21.21 16.00 4.78 1.78 12.62 16.64 0.74 2.41 15.88 5.56 11.10 1.73 1.40 2.92 0.41 0.41 4.20 2.42 A F E W B C D Gate P J E F H G MT1 MT2 M Q R N G H J K L M N P Q R U W K L Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Qxx25xx & Qxx25xHx Series 124 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Dimensions — TO-218X (J Package) — Isolated Mounting Tab C B U (diameter) D Dimension A B C D E F G H J K L M N P R S T U V W X Y Z Inches Min 0.810 0.610 0.178 0.055 0.487 0.635 0.022 0.075 0.575 0.256 0.220 0.080 0.169 0.034 0.113 0.086 0.156 0.164 0.603 0.000 0.003 0.028 0.085 Max 0.835 0.630 0.188 0.070 0.497 0.655 0.029 0.095 0.625 0.264 0.228 0.088 0.177 0.042 0.121 0.096 0.166 0.165 0.618 0.005 0.012 0.032 0.095 Millimeters Min 20.57 15.49 4.52 1.40 12.37 16.13 0.56 1.91 14.61 6.50 5.58 2.03 4.29 0.86 2.87 2.18 3.96 0.410 15.31 0.00 0.07 0.71 2.17 Max 21.21 16.00 4.78 1.78 12.62 16.64 0.74 2.41 15.88 6.71 5.79 2.24 4.49 1.07 3.07 2.44 4.22 0.420 15.70 0.13 0.30 0.81 2.42 Tc Measurement Point A F EZ MT1 W X J Gate N T M Y K V L R S P MT2 G H Note: Maximum torque to be applied to mounting tab is 8 in-lbs (0.904 Nm). . Dimensions — TO-3 (P Package) Fastpak — Isolated Mounting Tab A B D Dimension A B C D E F G H I J K L M N O P Q R S T (MT1) T (MT2) T (Gate) U (MT1) U (MT2) U (Gate) V W Inches Min 1.531 1.177 0.843 0.780 0.783 0.874 0.161 0.386 0.508 0.079 0.047 0.307 0.372 0.043 0.315 0.098 0.846 0.244 0.106 0.321 0.321 0.220 0.246 0.246 0.183 0.120 0.175 Max 1.543 1.185 0.850 0.795 0.791 0.906 0.169 0.465 0.587 0.087 0.055 0.319 0.396 0.059 0.331 0.106 0.886 0.256 0.130 0.329 0.329 0.228 0.254 0.254 0.191 0.130 0.185 Millimeters Min 38.90 29.90 21.40 19.80 19.90 22.20 4.10 9.80 12.90 2.00 1.20 7 .80 9.45 1.10 8.00 2.50 21.50 6.20 2.70 8.15 8.15 5.60 6.25 6.25 4.65 3.05 4.45 Max 39.20 30.10 21.60 20.20 20.10 23.00 4.30 11.80 14.90 2.20 1.40 8.10 10.05 1.50 8.40 2.70 22.50 6.50 3.30 8.35 8.35 5.80 6.45 6.45 4.85 3.30 4.70 MT2 F MT1 Gate G E C I J (MT1, MT2) T U W V R K (Gate) 5N S O P Q H TC Measur Point ing ML Thick ness off all three copper-alloy terminals is .032" (0.81 mm). Maximum torque to be applied to mounting tab is 8 in-lbs (0.904Nm). ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Qxx25xx & Qxx25xHx Series 125 Revised: May 10, 2010 09:33 PM 25 A TRIACs Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs Product Selector Part Number Qxx25R5 Qxx25N5 Qxx25P5 Qxx25RH5 Qxx25LH5 Qxx25NH5 Qxx25R6 Qxx25L6 Qxx25NH6 Qxx25J6 Qxx25K6 X X X X X X X X Voltage 400V X X 600V X X X X X X X X X X X 800V X X X X X X X X X X X X X X X 1000V X X Gate Sensitivity Quadrants I - II - III 50 mA 50 mA 50 mA 50 mA 50 mA 50 mA 80 mA 80 mA 80 mA 80 mA 80 mA IV 120 mA (TYP) 120 mA (TYP) 120 mA (TYP) Package TO-220R TO-263 D2-Pak Fastpak TO-220R TO-220L TO-263 D2-Pak TO-220R TO-220L TO-263 D2-Pak TO-218X TO-218AC Packing Options Part Number Qxx25R5 Qxx25R5TP Qxx25N5TP Qxx25N5RP Qxx25RH5 Qxx25RH5TP Qxx25LH5 Qxx25LH5TP Qxx25NH5TP Qxx25NH5RP Qxx25P5 Qxx25R6 Qxx25R6TP Qxx25L6 Qxx25L6TP Qxx25NH6TP Qxx25NH6RP Qxx25J6TP Qxx25K6TP Marking Qxx25R5 Qxx25R5 Qxx25N5 Qxx25N5 Qxx25RH5 Qxx25RH5 Qxx25LH5 Qxx25LH5 Qxx25NH5 Qxx25NH5 Qxx25P5 Qxx25R6 Qxx25R6 Qxx25L6 Qxx25L6 Qxx25NH6 Qxx25NH6 Qxx25J6 Qxx25K6 Weight 2.20g 2.20g 1.60g 1.60g 2.20g 2.20g 2.20g 2.20g 1.60g 1.60g 21.4g 2.20g 2.20g 2.20g 2.20g 1.60g 1.60g 5.23g 4.40g Packing Mode Bulk Tube Tube Embossed Carrier Bulk Tube Bulk Tube Tube Embossed Carrier Bulk Bulk Tube Bulk Tube Tube Embossed Carrier Tube Tube Base Quantity 500 500 (50 per tube) 500 (50 per tube) 500 500 500 (50 per tube) 500 500 (50 per tube) 500 (50 per tube) 500 200 500 500 (50 per tube) 500 500 (50 per tube) 500 (50 per tube) 500 250 (25 per tube) 250 (25 per tube) Qxx25xx & Qxx25xHx Series 126 Revised: May 10, 2010 09:33 PM ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors 25 Amp Standard & Alternistor (High Commutation) Triacs TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) Gate 0.059 DIA (1.5) MT1 / Cathode 0.945 (24.0) 0.827 (21.0) * * Cover tape MT2 / Anode 12.99 (330.0) Dimensions are in inches (and millimeters). 0.512 (13.0) Arbor Hole Dia. 1.01 (25.7) Direction of F eed Part Numbering System Q 60 25 N H6 DEVICE TYPE Q: Triac or Alternistor SENSITIVITY Standard Triac 5: 50mA Alternistor H5: 50mA 6: 80mA H6: 80mA PACKAGE TYPE L : TO-220AB Isolated R : TO-220AB Non-Isolated N : TO-263 (D2 -Pak) K : TO-218AC Isolated J : TO-218X Isolated P : Fastpak Part Marking System TO-220AB (R & L Packages) TO-263 (N Package) TO-218AC (K Package) TO-218X (J Package) Q6025K6 Q6025L5 ® VOLTAGE RATING 40: 400V 60: 600V 80: 800V K0: 1000V CURRENT RATING 25: 25A yxxxx ® yxxxx Fastpak (P Package) ® Q6025P5 yxxxx ©2010 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. 127 Revised: May 10, 2010 09:33 PM Qxx25xx & Qxx25xHx Series 25 A TRIACs