S402ES

Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs HF Sx02xS Series Description New 1.5 Amp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. All SCR’s junctions are glasspassivated to ensure long term reliability and parametric stability. Features Halogen-Free time (tq) < 35 μsec. mount packages Main Features Symbol IT(RMS) VDRM / VRRM IGT Value 1.5 400 to 600 200 Unit A V μA microprocessor interface capability > 15Amps (VDRM / VRRM ) capability — up to 600V Schematic Symbol A Applications The Sx02xS EV series is specifically designed for Gas Ignition applications that require high pulse surge current capability. G K Absolute Maximum Ratings Symbol IT(RMS) IT(AV) RMS on-state current (full sine wave) Average on-state current Parameter TO-92 SOT-223 TO-92 SOT-223 TO-92 SOT-223 tp = 10 ms tp = 8.3 ms di/dt IGM PG(AV) Tstg TJ Sx02xS Series Value TC = 65°C TL = 95°C TC = 65°C TC = 95°C F = 50 Hz F = 60 Hz F = 50 Hz F = 60 Hz TJ = 125°C TJ = 125°C TJ = 125°C 1.5 Unit A 0.95 12.5 A ITSM Non repetitive surge peak on-state current (Single cycle, TJ initial = 25°C) A 15.0 0.78 A2s 0.93 50 1.0 0.1 -40 to 150 -40 to 125 ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. I2t I2t Value for fusing Critical rate of rise of on-state current IG = 10mA Peak gate current Average gate power dissipation Storage junction temperature range Operating junction temperature range 201 Revised: December 22, 2010 09:54 AM TO-92 SOT-223 tp = 10 μs A/μs A W °C °C Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs Electrical Characteristics (TJ = 25°C, unless otherwise specified) Symbol IGT VGT VGRM IH Description DC Gate Trigger Current DC Gate Trigger Voltage Peak Reverse Gate Voltage Holding Current Critical Rate-of-Rise of Off-State Voltage Test Conditions Sx02xS Min 15 — 5 — Max 200 0.8 — 5 Unit μA V V mA VD = 12V RL = 60 Ω IRG = 10μA RGK = 1 kΩ TJ = 125°C VD = VDRM / VRRM Exponential Waveform RGK = 1 kΩ TJ = 125°C @ 600 V RGK = 1 kΩ IG = 10mA PW = 15μsec IT = 3.0A (pk) (dv/dt)s 25 — V/μs tq tgt Turn-Off Time — 35 μs Turn-On Time — 3 μs Static Characteristics (TJ = 25°C, unless otherwise specified) Symbol VTM Description Peak On-State Voltage Test Conditions ITM = 3.0A (pk) TJ = 25°C @ VD= VDRM RGK = 1 kΩ TJ = 125°C @ VD= VDRM RGK = 1 kΩ Value Min — — — Max 1.70 5 500 Unit V μA μA IDRM Off-State Current, Peak Repetitive Thermal Resistances Symbol Rth(j-c) Description Junction to case (AC) Test Conditions TO-92 IT = 1.5A (RMS)1 SOT-223 TO-92 Rth(j-a) 1 Value 50 Unit °C/W 25 160 °C/W 60 Junction to ambient IT = 1.5A (RMS)1 SOT-223 60Hz AC resistive load condition, 100% conduction. Sx02xS Series 202 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature 2.5 Figure 2: Normalized DC Holding Current vs. Junction Temperature 2.0 Normalized Gate: Trigger Current IGT @ Tj / IGT@ 25ºC Normalized Holding Current (IH @ TJ / IH @25∞C) 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 -40 -25 -10 +5 +20 +35 +50 +65 +80 +95 +110 +125 0.0 -40 -25 -10 +5 +20 +35 +50 +65 +80 +95 +110 +125 Junction Temperature (TJ) °C Junction Temperature (TJ) °C Figure 3: Normalized DC Gate Trigger Voltage vs. Junction Temperature 1.5 Figure 4: Power Dissipation (Typical) vs. RMS On-State Current 1.5 Average Power Dissipation, PD (Watts) Normalized Gate: Trigger Voltage CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180o 1.0 (VGT @ Tj / VGT @ 25ºC) 1.0 0.5 0.5 -40 -25 -10 +5 +20 +35 +50 +65 +80 +95 +110 +125 0.0 0.0 0.5 1.0 1.5 Junction Temperature (TJ) °C RMS On-state Current [IT(RMS)] (Amps) Figure 5: Maximum Allowable Case Temperature vs. On-State Current Max Allowable Case Temperature, TC (Celsius) 130 120 SOT-223 110 100 TO-92 90 80 70 60 50 0.0 0.5 1.0 1.5 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180o CASE TEMPERATURE: Measured as shown on dimensional drawings RMS On-state Current [IT (RMS)] (Amps) Sx02xS Series 203 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs Figure 6: Surge Peak On-State Current vs. Number of Cycles 20 Peak Surge (Non-repetitive) On-State Current (ITSM) – Amps. 15 12 10 9 8 7 6 5 4 3 1.5 AD evic es Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State Current [IT(RMS)]: Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 2 1 1 2 3 4 5 6 7 8 9 10 20 30 40 60 80 100 200 300 400 600 1000 Surge Current Duration – Full Cycle Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (ts) Pb – Free assembly TP Temperature 150°C 200°C 60 – 180 secs 5°C/second max 5°C/second max 217°C 60 – 150 seconds 260 +0/-5 tP Ramp-up TL TS(max) Preheat Preheat tL Ramp-do Ramp-down TS(min) tS 25 time to peak temperature Time Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed °C 20 – 40 seconds 5°C/second max 8 minutes Max. 280°C Sx02xS Series 204 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs Physical Specifications Terminal Finish 100% Matte Tin-plated. Environmental Specifications Test AC Blocking Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C 1008 hours; -40°C MIL-STD-750, M-1056 10 cycles; 0°C to 100°C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121°C at 2 ATMs) and 100% R/H MIL-STD-750 Method 2031 ANSI/J-STD-002, category 3, Test A MIL-STD-750, M-2036 Cond E Body Material UL recognized epoxy meeting flammability classification 94V-0. Copper Alloy Temperature Cycling Lead Material Temperature/ Humidity Design Considerations Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. High Temp Storage Low-Temp Storage Thermal Shock Autoclave Resistance to Solder Heat Solderability Lead Bend Dimensions — TO-92 (E Package) A TC MEASURING POINT Inches Dimensions Min Max 0.205 0.210 Millimeters Min 4.450 4.320 12.70 3.430 0.165 0.105 0.021 0.055 0.105 0.020 3.180 2.040 0.407 1.150 2.420 0.380 4.190 2.660 0.533 1.390 2.660 0.500 Max 5.200 5.330 B A 0.175 0.170 SEATING PLANE C D 0.500 0.135 0.125 0.080 0.016 0.045 0.095 0.015 C GATE E F G G H CATHODE I D ANODE H I J E J F F Sx02xS Series 205 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs Dimensions – SOT-223 Anode Gate Cathode Anode Inches Dimensions Min Typ 0.256 0.138 — — 0.118 0.027 0.090 0.181 0.276 0.010 Max 0.264 0.146 0.071 0.004 0.124 0.034 — — 0.287 0.014 Min 6.30 3.30 — 0.02 2.90 0.60 — — 6.70 0.24 Millimeters Typ 6.50 3.50 — — 3.00 0.70 2.30 4.60 7 .00 0.26 Max 6.70 3.70 1.80 0.10 3.15 0.85 — — 7 .30 0.35 Pad Layout for SOT-223 3.3 (0.130”) A 0.248 0.130 C 1.5 (0.059”) — 0.001 0.114 0.024 — — 0.264 0.009 D 1.2 (0.047”) (3x) E 2.3 (0.091”) 6.4 (0.252”) F G 1.5 (0.059”) 4.6 (0.181”) H I Dimensions in Millimeters (Inches) J K 10° MAX Product Selector Part Number S402ES S602ES S402TS S602TS Voltage 400V X — X — 600V — X — X Gate Sensitivity 200μA 200μA 200μA 200μA Package TO-92 TO-92 SOT-223 SOT-223 Packing Options Part Number Sx02ES Sx02ESAP Sx02ESRP Sx02TSRP Note: x = voltage Marking Sx02ES Sx02ES Sx02ES Sx02TS Weight 0.170 g 0.170 g 0.170 g 0.120 g Packing Mode Base Quantity 2500 Ammo Pack Tape & Reel Tape & Reel 2000 2000 1000 Sx02xS Series 206 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-C Standards 1.6 (41.0) 0.236 (6.0) 0.02 (0.5) 0.098 (2.5) MAX 1.26 (32.0) 0.708 (18.0) 0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) Anode Cathode 0.2 (5.08) Gate 0.157 DIA (4.0) Flat up 1.97 (50.0) Dimensions are in inches (and millimeters). Direction of Feed TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.236 (6.0) 1.62 (41.2) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.27 (32.2) 0.354 (9.0) 0.5 (12.7) 0.1 (2.54) Anode 0.2 (5.08) Cathode Gate 0.157 (4.0) DIA Flat down Directio n of Feed 25 Devices per fold 1.85 (47.0) 12.2 (310.0) Dimensions are in inches (and millimeters). 1.85 (47.0) 13.3 (338.0) Sx02xS Series 207 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information. Teccor® brand Thyristors EV Series 1.5 Amp Sensitive SCRs SOT-223 Reel Pack (RP) Specifications 1.5 mm 4 mm 8 mm 2 mm A 1.75 mm 5.5 mm 12 mm K A GATE 180 mm 13 mm Abor Hole Diameter 13.4 mm Part Numbering System Part Marking System S x 02 x xx xx SCR SERIES PACKING TYPE Blank: Bulk RP: Reel Pack (TO-92) : Embossed Carrier Pack (SOT-223) AP: Ammo Pack (TO-92) SENSITIVITY S: 200μA Sensitive SCR PACKAGE TYPE E: TO-92 T: SOT-223 K A VOLTAGE 4: 400V 6: 600V CURRENT 02: 1.5A YM YM XXX K A G G A XX X Sx02xS Series 208 Revised: December 22, 2010 09:54 AM ©2011 Littelfuse, Inc Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.