T10A080E

T10A SIDACtor® Device RoHS The bi-directional T10A devices are a through-hole technology SIDACtor protector. It is intended for cost-sensitive telecommunication applications. This T10 SIDACtor series enables equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * T10A060B T10A060E T10A062 T10A068 T10A080B T10A080E T10A100 T10A110B T10A110E T10A120 T10A130 T10A140B T10A140E T10A180 T10A180B T10A180E T10A200 T10A220 T10A220B T10A220E T10A240 T10A270 T10A270B T10A270E VDRM @ 5 µA Volts 58 58 60 65 75 75 100 110 110 120 130 140 140 180 175 175 200 220 215 215 240 270 270 270 VS Volts 80 80 82 90 120 120 133 135 135 160 173 170 170 240 210 210 267 293 265 265 320 360 360 360 VT Volts 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 IS mAmps 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 800 IH mAmps 120 180 150 150 120 180 150 120 180 150 150 120 180 150 120 180 150 150 120 180 150 150 120 180 pF TYP 50 50 50 50 43 43 43 38 38 38 38 34 34 34 32 32 30 30 30 30 30 30 30 30 * For surge ratings, see table below. General Notes: • All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. • IPP is a repetitive surge rating and is guaranteed for the life of the product. • Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. • VDRM is measured at IDRM. • VS is measured at 0.5 V/µs. • Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. Surge Ratings in Amps IPP 8x20 * 1.2x50 ** Series A * Current waveform in µs ** Voltage waveform in µs Amps 100 5x310 * 10x700 ** Amps 37.5 10x1000 * 10x1000 ** Amps 50 ITSM 50 / 60 Hz Amps 30 di/dt Amps/µs 100 Telecom Design Guide • © 2006 Littelfuse 3 - 25 www.littelfuse.com SIDACtor Devices T10A SIDACtor® Device Thermal Considerations Package DO-15 Symbol TJ TS RθJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value 150 -40 to +150 60 Unit °C °C °C/W +I IPP – Peak Pulse Current – %IPP tr = r ise time to peak value td = decay time to half value IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 tr td t – Time (µs) -I V-I Characteristics tr x td Pulse Waveform Percent of VS Change – % 10 IH (TC = 25 ˚C) 14 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 ˚C 25 ˚C Ratio of Case Temperature (TC) – ˚C Junction Temperature (TJ) – ˚C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature www.littelfuse.com 3 - 26 © 2006 Littelfuse • Telecom Design Guide