T10B080BXX

SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) T10B Series - DO-201 Description T10B Series are SIDACtor® devices designed protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a robust and cost effective throughhole solution that enables equipment to comply with global regulatory standards Features and Benefits Low voltage overshoot Low on-state voltage Does not degrade with use Applicable Global Standards TIA-968-A GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Fails short circuit when surged in excess of ratings High Surge Current Rating Agency Approvals Agency Agency File Number E128662 Pinout Designation Not Applicable Schematic Symbol TIA-968-B ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building Electrical Characteristics VDRM @lDRM=5μA V Min T10B080Bxx T10B110Bxx T10B140Bxx T10B180Bxx T10B220Bxx T10B270Bxx T10B080Exx T10B110Exx T10B140Exx T10B180Exx T10B220Exx T10B270Exx T10B080B T10B110B T10B140B T10B180B T10B220B T10B270B T10B080E T10B110E T10B140E T10B180E T10B220E T10B270E 70 100 120 170 200 240 70 100 120 170 200 240 VS @100V/μs V Max 125 142 178 220 275 370 125 142 178 220 275 370 IH IS IT A Max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amp V Max 4 4 4 4 4 4 4 4 4 4 4 4 Capacitance @1MHZ, 2V Bias pF 60 55 48 44 41 36 60 55 48 44 41 36 Part Number Marking mA Min mA Max 120 120 120 120 120 120 180 180 180 180 180 180 800 800 800 800 800 800 800 800 800 800 800 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). - XX Part Number Suffix: ‘RP’ (Reel Pack), Blank (Bulk Pack), or ‘60’ (Type 60 lead form, Bulk Pack) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 180 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings IPP Series 8x201 1.2x502 A min B Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < 5x3101 10x7002 A min 125 10x10001 10x10002 A min 100 ITSM 50/60 Hz A min 30 di/dt A/μs max 500 250 Thermal Considerations Package DO-201AD Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient 120 Value Unit °C °C °C/W V-I Characteristics +I tr x td Pulse Waveform tr = r ise time to peak value td = decay time to half value IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 14 Percent of VS Change – % 12 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Junction Temperature (TJ) – °C Ratio of Case Temperature (TC) - ºC © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 181 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 TP Ramp-up tP Critical Zone TL to TP Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Temp Cycling UL recognized epoxy meeting flammability classification 94V-0 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 182 Revised: February 22, 2011 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Part Numbering Part Marking T10B xxx x xx XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Blank: Bulk Pack RP: Reel Pack MEDIAN VOLTAGE HOLDING CURRENT B: 120mA E: 180mA T10Bxxxx TYPE T10B: SIDACtor T10B series PACKING OPTIONS Date Code Dimensions — DO-201AD Inches MIN 0.028 0.190 0.360 1 MAX 0.042 0.205 0.375 Millimeters MIN 0.711 4.826 9.146 25.4 MAX 1.067 5.207 9.527 D B Dimension B D L G L G L Packing Options Package Type Added Suffix RP N/A Industry Standard Tape and Reel Specification — DO-201AD Description DO-201AD Tape and Reel Pack DO-201AD Bulk Pack Quantity 1000 500 EIA-RS-296-D N/A 2.55 64.8 0.35 8.99 Off Center Both Side 0.84 (21.33) 2.0 50.8 T10B 0.085 21.6 0.24 6.1 Direction of Feed Top View 2.7 68.6 Dimensions are in inches/mm Recess Depth Max. 0.75 (19.55) 86.36 3.4 Front View 0.6 15.24 14 355.6 Label © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 183 Revised: February 22, 2011