LR432ATLT1G

LESHAN RADIO COMPANY, LTD. 352*5$00$%/(35(&,6,215()(5(1&( LR432ATLT1G   Description The LR432ATLT1G is a three-terminal adjustable regulator with a guaranteed thermal stability over applicable temperature ranges.The output voltage may be set to any value between VREF (approximately 1.24V) and 18V with two external resistors. It provides very wide applications,including shunt regulator,series regulator,switching regulator,voltage reference and others. SOT-23 SOT-23 1: Ref; 2: Cathode; 3: Anode Features: • Precise Reference Voltage to 1.24V • Guaranteed 0.5% Reference Voltage Tolerance • Sink Current Capability, 55µA to100mA • Quick Turn-on • Adjustable Output Voltage, Vo=VREF to 18V • 0.05 Ω Typical Output Impedance • We declare that the material of product is ROHS compliant and does not contain any B r, Cl, and Sb203 • ESD HB M 7000V  CATHODE(K) REFERENCE(R) ANODE(A)    Ver 1.5 1/11 LESHAN RADIO COMPANY, LTD. Absolute Maximum Ratings Symbol VKA IK I REF Tj Topr Parameter Cathode voltage Continuous cathode current range Reference current range Operating Junction Temperature Range Operating Ambient Temperature Electrical Characteristcs Characteristic (Typical and limits apply for TJ=2 Test Circuit Symbol 3 VREF 0.5% Reference Voltage Rating 20 100 10 150 - 40 to 125 1% Deviation of Reference Voltage Over-Temperature 3 Ratio of Change in VREF to the Change in Cathode Voltage 4 Reference Input Current 4 Deviation of Reference Current Over Full Temperature Range 4 Minimum Cathode Current for Regulation 3 Off-State Cathode Current 5 Dynamic Impedance 3 Test conditions VKA=VREF,IKA=10mA VREF VREF/ VKA VKA=VREF IKA=10mA 0 to 70°C -20 to 125°C -40 to 125°C VKA: VREF to 16V IKA=10mA, R1=10K , R2= IKA=10mA, R1=10K , R2= IREF IREF IKA (MIN) Unit V mA mA °C °C unless otherwise noted.) MIN TYP MAX 1.234 1.240 1.246 1.228 1.240 1.252 2 10 3 8 15 25 -0.5 -1.5 0.15 0.4 A 0.1 0.4 A 55 80 A V mV mV/V TA=-20 to 85°C VKA=VREF VREF=0, VKA=18V 0.04 0.50 (OFF) VKA=6V, VREF=0 0.01 0.05 ZKA VKA=VREF, IKA=1 to 100mA f 1.0kHz 0.05 0.15 IKA UNIT A Classif ication of V ref and pack age Marking RanK Vref(V) 9D 1.0% 1.24 LR432BTLT1G 0.5% 1.24 LR432APTLT1G 1.0% 1.25 LR432BPTLT1G 0.5% 1.25 Device LR432ATLT1G Packgage: SOT23 2/11 LESHAN RADIO COMPANY, LTD. TEST CIRCUIT TYPICAL PERFORMANCE CHARACTERISTICS  3/11 LESHAN RADIO COMPANY, LTD. 4/11 LESHAN RADIO COMPANY, LTD. 5/11 LESHAN RADIO COMPANY, LTD. TYPICAL APPLICATIONS 6/11 LESHAN RADIO COMPANY, LTD. Chip Size(before saw) 0.72 *0.68 (mm)2 7/11 LESHAN RADIO COMPANY, LTD. SOT-23 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M,1982 2. CONTROLLING DIMENSION: INCH. A L 3 1 V 2 DIM B S G C D H K J MIN 0.1102 0.0472 0.0350 0.0150 0.0701 0.0005 0.0034 0.0140 0.0350 0.0830 0.0177 A B C D G H J K L S V INCHES MAX 0.1197 0.0551 0.0440 0.0200 0.0807 0.0040 0.0070 0.0285 0.0401 0.1039 0.0236 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm 8/11 LESHAN RADIO COMPANY, LTD. Tape & Reel and Packaging Specifications Embossed Tape and Reel is used to facilitate automatic pick and place equipment feed requirements. The tape is used as the shipping container for various products and requires a minimum of handling. The antistatic/conductive tape provides a secure cavity for the product when sealed with the “peel–back” cover tape. • Two Reel Sizes Available (7"and 13",) • SOT–23, SC–70/SOT–323, • Used for Automatic Pick and Place Feed Systems SC–89, SC–88/SOT–363, SC–88A/SOT–353, • Minimizes Product Handling SOD–323, SOD-523 in 8 mm Tape • EIA 481, –1, –2 Use the standard device title and add the required suffix as listed in the option table below (Table 1). Note that the individual reels have a finite number of devices depending on the type of product contained in the tape. Also note the minimum lot size is one full reel for each line item, and orders are required to be in increments of the single reel quantity. SOD-323 SC-59, SC-70, SC-75,SOT-23 8 mm 8 mm SC-88, SOT-363 T1 Orientation SC-88A, SOT-353 T1 Orientation 8 mm 8 mm Direction of Feed Typical Reel Orientations Table 1. EMBOSSED TAPE AND REEL ORDERING INFORMATION Tape Width (mm) Package SOT–23 8 Pitch mm 4 8 8 SC–70/SOT–323 4 8 8 4 Reel Size mm(inch) Devices Per Reel and Minimum Device Suffix 178 Order Quantity (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 178 (7) 3,000 T1 330 (13) 10,000 T3 SC–89 8 SC–88/SOT-363 8 4 8 8 SC–88A/SOT-353 SOD-323 4 8 8 4 8 8 4 SOD-523 8 9/11 LESHAN RADIO COMPANY, LTD. EMBOSSED TAPE AND REEL DATA FOR DISCRETES CARRIER TAPE SPECIFICATIONS P0 K D t P2 10 Pitches Cumulative Tolerance on Tape ± 0.2mm( ± 0.008’’ ) E Top Cover Tape B1 A0 F See Note 1 P Center Lines of Cavity Embossment For Machine Reference Only Including Draft and RADII Concentric Around B0 *Top Cover Tape Thickness(t 1 ) 0.10mm (0.004’’ )Max. Bar Code Label Tape and Components Shall Pass Around Radius “R” 10 D1 For Components 2.0mm x 1.2mm and Larger User Direction of Feed R Min Bending Radius W B0 K0 Embossed Carrier 100 mm (3.937 ’’) 1 mm Max Without Damage o Maximum Component Rotation Typical Component Cavity Center Line Typical Component Center Line Embossment Tape 1 mm(.039’’ ) Max 250 mm (9.843’’) Camber (Top View) Allowable Camber To Be 1 mm/100 mm Nonaccumulative Over 250 mm DIMENSIONS Tape Size B1 Max 4.55mm (.179’’) 8.2mm 12mm (.323’’) 12.1mm 16mm (.476’’) 20.1mm 24mm (.791’’) 8mm D 1.5+0.1mm - 0.0 (.059+.004’’ - 0.0) D1 E 1.0Min 1.75 ± 0.1mm (.039’’) (.069±.004) 1.5mmMin (.060’’) F 3.5 ± 0.05mm (.138±.002’’) 5.5 ± 0.05mm (.217 ± .002’’) 7.5 ± 0.10mm (.295 ± .004’’) 11.5 ± 0.1mm (.453 ± .004’’) K P0 2.4mm Max 4.0 ± 0.1mm (.094’’) (.157 ± .004’’) 6.4mm Max (.252’’) 7.9mm Max (.311’’) 11.9mmMax (.468’’) P2 RMin TMax WMax 2.0 ± 0.1mm (.079 ± .002’’) 25mm 0.6mm (.98’’) (.024’’) 30mm (1.18’’) 8.3mm (.327’’) 12 ± .30mm (.470 ± .012’’) 16.3mm (.642’’) 24.3mm (.957’’) Metric dimensions govern - English are in parentheses for reference only. NOTE 1: A 0 , B 0 , and K 0 are determined by component size. The clearance between the components and the cavity must be within .05 mm min. to.50 mm max., NOTE 2: the component cannot rotate more than 10 o within the determined cavity. NOTE 3: If B1 exceeds 4.2 mm (.165”) for 8 mm embossed tape, the tape may not feed through all tape feeders. 10/11 LESHAN RADIO COMPANY, LTD. EMBOSSED TAPE AND REEL DATA FOR DISCRETES T Max Outside Dimension Measured at Edge 13.0mm ± 0.5mm 1.5mm Min (.512 ±.002’’) (.06’’) A 50mm Min (1.969’’) 20.2mm Min (.795’’) Full Radius G Inside Dimension Measured Near Hub Size 8 mm 12mm 16mm 24 mm A Max G 330mm 8.4mm+1.5mm, -0.0 (.33’’+.059’’, -0.00) 12.4mm+2.0mm, -0.0 (.49 ’’+ .079’’, -0.00) 16.4mm+2.0mm, -0.0 (.646’’+.078’’, -0.00) 24.4mm+2.0mm, -0.0 (.961’’+.070’’, -0.00) (12.992’’) 330mm (12.992’’) 360mm (14.173’’) 360mm (14.173’’) T Max 14.4mm (.56’’) 18.4mm (.72’’) 22.4mm (.882’’) 30.4mm (1.197’’) Reel Dimensions Metric Dimensions Govern –– English are in parentheses for reference only Storage Conditions Temperature: 5 to 40 Deg.C (20 to 30 Deg. C is preferred) Humidity: 30 to 80 RH (40 to 60 is preferred ) Recommended Period: One year after manufacturing (This recommended period is for the soldering condition only. The characteristics and reliabilities of the products are not restricted to this limitation) 11/11