SM3200A

SM3150A thru SM3200A Schottky Barrier Rectifiers Reverse Voltage 150 to200V Forward Current 3.0A FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low power loss,high efficiency * For use in low voltage high frequency inverters, free wheeling,and polarity protection applications * Guardring for over voltage protection * High temperature soldering guaranteed: 260°C/10 seconds at terminals Mechanical Data Case: JEDEC DO-214AC, molded plastic over glass die Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 We declare that the material of product compliance Polarity: Color band denotes cathode end with ROHS requirements Mounting Position: Any Weight: 0.0023 oz., 0.065 g Handling precautin:None Electrical Characteristic 1.Maximum Ratings & Thermal Characteristics Ratings at 25°C ambient temperature unless otherwise specified. Parameter Symbol symbol device marking code SM3150A SM3200A S315 S320 Unit Maximum repetitive peak reverse voltage VRRM 150 200 V Maximum RMS voltage VRMS 105 140 V Maximum DC blocking voltage VDC 150 200 V Maximum average forward rectified current 0.375" (9.5mm) lead length (See fig. 1) IF(AV) 3.0 A IFSM 80 A Typical thermal resistance (Note 1) RθJA 50 °C/W Operating junction and storage temperature range TJ, TSTG –40 to +150 °C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Electrical Characteristics Ratings at 25°C ambient temperature unless otherwise specified. Parameter Symbol symbol SM3150A SM3200A Unit Maximum instantaneous forward voltage at 3.0A VF 0.87 V Maximum DC reverse current TA = 25°C at rated DC blocking voltage TA = 100°C IR 0.5 10.0 mA Typical junction capacitance at 4.0V, 1MHz CJ 110 PF NOTES: 1. 8.0mm2 (.013mm thick) land areas SM3150A thru SM3200A 2.Ratings and Characteristic Curves ( TA = 25°C unless otherwise noted ) Fig. 2 – Maximum Non-repetitive Peak Forward Surge Current 3.0 40 0 0 100 Instantaneous Forward Current (A) TJ = TJ max 8.3ms Single Half Sine-wave (JEDEC Method) 80 1.5 0 Fig 3. – Typical Instantaneous Forward Characteristics TJ = 25°C Pulse width = 300µs 1% Duty Cycle 10 1 25 50 75 100 125 150 175 Ambient Temperature, °C 10 Number of Cycles at 60Hz 100 Fig 4. – Typical Reverse Characteristics 10 Tj=125℃ 1.0 1.0 0.1 Tj=75℃ 0.1 0.01 0.01 0.2 100 0.4 0.6 0.8 1.0 1.2 Instantaneous Forward Voltage (V) Fig 5. –typical transient thermal impedance Tj=25℃ 0.001 0 20 40 60 80 100 Percent of Rated Peak Reverse Voltage (%) Fig 6. – Typical Junction Capacitance 1000 Junction Capacitance (pF) Transient thermal impedance(°C/W) Peak forward surge current (A) 60 Hz Resistive or Inductive Load Instantaneous Reverse Current (mA) Average Forward Rectified Current (A) Fig. 1 – Forward Current Derating Curve 10 TJ = 25°C f = 1.0 MHz Vsig = 50mVp-p 100 1.0 0.1 0.01 0.1 1.0 10 t,Pulse duration,sec 100 10 0.1 1 10 Reverse Voltage (V) 100 SM3150A thru SM3200A 3. dimension: SM3150A: " S"--肖特基产品；"M"--表面贴装； "3"--正向电流3A; " 150"---VB为150V; "A"--SMA封装； 文件编号： 标题Titile: 塑封生产线SMD产品包装规范 第 3 版 Packaging specification of SMD 第 WI-258 第 0 次修改 2 页 SMD产品通用包装材料规格以及包装产品数量 General packaging materials spec. and quantity 1.1 卷装 reel A.卷盘规格reel spec 单位：mm 规格 SMA 7"卷盘 SMA13"卷盘 SMB13"卷盘 SMC13"卷盘 A 177.0±2.0 330.0±2.0 330.0±2.0 330.0±2.0 B 54.0±0.5 75.0±0.5 75.0±0.5 75.0±0.5 C 13.0±0.5 13.0±0.5 13.0±0.5 13.0±0.5 每卷数量 2K 5K 3K 3K W 13.2±0.2 13.2±0.2 13.5±0.5 17.0±0.5 B. 13"卷盘内盒 inner box 单位：mm 尺寸 A 335±5.0 B 335±2.0 C 40±1.0 按以上包装方式，产品包装数量：quantity 规格 SMA13"卷盘 SMB13"卷盘 SMC13"卷盘 每盒数量 10K 6K 6K 标题Titile: 塑封生产线SMD产品包装规范 文件编号： WI-258 文件编号： WI-258 Packaging specification of SMD 第 3 页 C. 7"卷盘盒 box 单位：mm 尺寸 A B C 188±2.0 188±2.0 138±2.0 按以上包装方式，产品包装数量：quantity 每盒数量 16K 7"卷盘 D. 卷盘外箱 reel carton 单位：mm 尺寸 A B C 350±2.0 340±2.0 350±2.0 按以上包装方式，产品包装数量： 规格 SMA 7"卷盘 SMA13"卷盘 SMB13"卷盘 SMC13"卷盘 1.2 编带规格 tape spec A. 盖带 Cover tape 单位：mm A SMA SMB 9.30±0.10 SMC 13.30±0.10 B 0.068±0.005 每箱数量 80K 80K 48K 36K 文件编号： 标题Titile: 第 3 版 Packaging specification of SMD B. 载带 t Do Po P2 B' 第 P1 A D1 A' Bo W F E 塑封生产线SMD产品包装规范 B SEC.:B-B' Ao Ko 产品负极端(编 带有孔一边） SEC.:A-A' WI-258 第 0 次修改 4 页 类型 SMA SMB SMC W 12±0.3 12±0.3 16±0.3 P1 4±0.1 8±0.1 8±0.1 E 1.75±0.1 F 5.5±.05 1.75±0.1 1.75±0.1 5.5±0.05 7.5±.05 D0 D1 1.55±0.05 1.55±0.05 1.55±0.05 1.5±0.1 1.55±0.05 1.55±0.05 P0 4±0.1 4±0.1 4±0.1 P2 2±0.05 2±0.05 2±0.05 10P0 40±0.2 40±0.2 40±0.2 A0 2.79±0.1 3.8±0.1 6.05±0.1 B0 5.33±0.1 5.4±0.1 8.31±0.1 K0 2.36±0.1 T 2.45±0.1 2.54±0.1 0.25±0.05 0.25±0.05 0.25±0.05 2、SMD产品通用包装规范 General spec of SMD 5.2.1国内客户domestic A. 7"卷盘reel 所有标签贴在卷盘负极 all the label on cathode side Ｂ A C C A处:贴LRC标签; B处:贴ROHS标签 C处:贴无卤标签 HF label B. 13"卷盘 所有标签贴在卷盘负极 all the label on （无卤产品才贴HF cathode side only） A Ｂ C Ｂ C A A处:贴LRC标签; B处:贴ROHS标签 C处:贴无卤标签（无卤产品才贴HF only） 文件编号： 标题Titile: 塑封生产线SMD产品包装规范 第 3 版 Packaging specification of SMD 第 WI-258 第 0 次修改 5 页 C. 标签要求label spec： LRC标签label ****** LRC产品型号 type ****** 产品数量 quantity ****** 产品批号 LOT ****** 产品生产日期 ROHS标签 date 无卤标签 HF label Green 2.2 国外客户 overseas 所有标签贴在卷盘负极 all the label on cathode side A Ｂ C 7"卷盘盒 inner box 13"卷盘内盒inner box Ｂ C C A A处:贴LRC标签; B处:贴ROHS标签 C处:贴无卤标签HF label （无卤产品才贴HF only） 文件编号： 标题Titile: 塑封生产线SMD产品包装规范 第 3 版 Packaging specification of SMD 第 WI-258 第 0 次修改 6 页 LRC标签label TYPE:****** MARK:****** Q'TY:****** DATE:****** LRC产品型号 印字型号 产品数量 产品生产日期 ROHS标签 无卤标签 HF label Green 注意事项NOTE: 1. 13"卷盘内盒装好产品,需用热缩膜包装;13"reel’inner box must be packed by shrink film 2. 所有编带产品卷装完成后,用白色胶带将编带粘牢; every tape after packing，must be fixed by white adhesive tape 3.1产品出厂检验报告 testing report of the OQC 每批出货时，需要附上出厂检验报告 every lot must with test report 3.2尾箱 同一编码每批次只允许出现一个尾数箱，对于尾数物料，须用缓冲材料对空余部分填充好， 保证物料在受到一定的外作用力下不发生明显移动，且物料间无碰撞。 The same coding is only one ending for each batch box materials for the mantissa to be good filled with cushioning material. SM3150A thru SM3200A 4. Update Record 版次 更新记录 更新作者 更新日期 1 第一版 周杰 2012.07.27