KWM-30581CSG

KWM-30581XY SERIES 5 x 8 Dot Matrix (3.0mm Dot) Multi-Color LED Display DESCRIPTION: The KWM-30581XY series is 37.40mm (1.47") height 5 x 8 multi-color dot matrix display. This multi-color series is suitable for use in single/multi-line message display, large area graphics display and electronic games. All devices are available as either common row anode or common row cathode. PACKAGE DIMENSIONS COL 1 4.60*7=32.90(1.295) 2 3 4 5 1 2 3 4 5 6 7 PIN1 4.70*4=18.80(0.740) φ3.00(0.118) 37.40(1.470) 8 ROW ABSOLUTE MAXIMUM RATINGS: (Ta=25 C) Parameter Max Reverse Voltage per segment 5V Reverse Current per segment (Vr = 5V) 100µA Derating Linear from 25oC per segment 0.4mA/ oC Operating Temperature Range -40oC To 85oC Storage Temperature Range -40oC To 100oC Soldering Temperature 1.6mm(1/16") from body for 5 sec. at 260oC NOTES : 1. All dimensions are in millimeters (inches). 2. Tolerance is +0.25mm(0.010) unless otherwise specified. 3. Specifications are subject to change without notice. 4. NP: No Pin. 5. NC: No Connect. o 23.40(0.921) 8.0(0.315) 6.0(0.236) 2.0*8=16.0(0.630) φ0.5(0.020) 28.08(1.134) INTERNAL CIRCUIT DIAGRAM ROW CATHODE COL 1 2 PIN 1 18 NO. PIN NO. 16 15 17 14 8 5 6 9 2 3 3 13 4 4 12 7 5 10 11 ROW ANODE COL 1 PIN 1 18 NO. PIN NO. 16 15 17 14 8 5 6 9 2 2 3 3 13 4 4 12 7 5 10 11 ROW 1 2 3 ROW 1 2 3 4 5 6 7 8 TESTING CONDITION FOR EACH PARAMETER : Parameter Forward Voltage Peak Emission Wave Length Spectral Line Half-Width Reverse Current Average Luminous Intensity Symbol Vf λρ ∆λ Ir Iv Unit V nm nm µA µ cd Test Condition If=20mA If=20mA If=20mA Vr=5V If=10mA 4 5 6 7 8 GREEN, SUPER GREEN RED, SUPER RED, YELLOW GREEN, SUPER GREEN RED, SUPER RED, YELLOW PART NO. SELECTION AND APPLICATION INFORMATION (RATINGS AT 25 C AMBIENT) Chip Part No. Raw Material GaAsP/GaP KWM-30581A32 GaP GaAlAs KWM-30581ASG GaP GaAsP/GaP KWM-30581A62 GaP GaAsP/GaP KWM-30581C32 GaP GaAlAs KWM-30581CSG GaP GaAsP/GaP KWM-30581C62 GaP Green 565 30 100 50 100 1.7 2.2 2.6 10-20 750 1400 REMARKS : 1. The average luminous intensity is obtained by summing the luminous intensity of each segment and dividing by the total number of segments. 2. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (International Commission on Illumination) eye-response curve. 3. Clean only by pure water, isopropanol, ethanol, Freon TF (or equivalent). o Wave Emitted Color Hi-Eff Red Green Super Red Common Anode C.C or C.A Length λρ (nm) 635 565 660 570 585 565 635 565 Common 660 570 585 Absolute Maximum Ratings ∆λ Pd If Electro-optical Characteristic If If Vf (V) Iv (µcd) (Peak) (Rec) Per Dot Per Dot (nm) (mW) (mA) (mA) Min. Typ. Max. mA Min. Typ. 45 30 20 30 30 30 45 30 20 30 30 100 100 100 100 100 100 100 100 100 100 100 50 50 50 50 50 50 50 50 50 50 50 100 100 100 100 100 100 100 100 100 100 100 1.7 1.7 1.5 1.7 1.7 1.7 1.7 1.7 1.5 1.7 1.7 1.9 2.2 1.9 2.2 1.9 2.2 1.9 2.2 1.9 2.2 1.9 2.6 10-20 850 2.6 10-20 750 1500 1400 2.6 10-20 1500 3000 2.6 10-20 800 2.6 10-20 750 2.6 10-20 750 2.6 10-20 850 2.6 10-20 750 1550 1400 1400 1500 1400 Super Green Yellow Green Hi-Eff Red Green Super Red 2.6 10-20 1500 3000 2.6 10-20 800 2.6 10-20 750 1550 1400 Super Green Cathode Yellow