KWM-30881C3

KWM-30881 SERIES 8 x 8 Dot Matrix (3.0mm Dot) LED Display DESCRIPTION: The KWM-30881 series is 32.00mm (1.26") height 8 x 8 dot matrix display. This series is suitable for use in single/multi-line message display, large area graphics display and electronic games. All devices are available as either common row anode or common row cathode. PACKAGE DIMENSIONS COL 1 2 3 4 5 6 7 8 1 2 4.0*7=28.0(1.102) 3 32.0(1.260) 4 5 6 7 8 PIN1 ABSOLUTE MAXIMUM RATINGS: (Ta=25 C) Parameter Max Reverse Voltage per segment 5V Reverse Current per segment (Vr = 5V) 100µA Derating Linear from 25oC per segment 0.4mA/ oC Operating Temperature Range -40oC To 85oC Storage Temperature Range -40oC To 100oC Soldering Temperature 1.6mm(1/16") from body for 5 sec. at 260oC NOTES : 1. All dimensions are in millimeters (inches). 2. Tolerance is +0.25mm(0.010) unless otherwise specified. 3. Specifications are subject to change without notice. 4. NP: No Pin. 5. NC: No Connect. 8.0(0.315) o 4.0*7=28.0(1.102) 32.0(1.260) φ3.00(0.118) ROW 5.00(0.196) 2.54*7=17.78(0.700) φ0.5(0.020) 24.0(0.945) INTERNAL CIRCUIT DIAGRAM ROW CATHODE COL 1 ROW PIN NO. 9 14 8 12 1 7 2 5 PIN NO. 13 ROW ANODE 3 4 2 3 4 10 5 6 6 11 7 15 8 16 COL 1 ROW PIN NO. 9 14 8 12 1 7 2 5 PIN NO. 13 2 3 3 4 4 10 5 6 6 11 7 15 8 16 1 2 1 2 3 4 5 6 7 8 TESTING CONDITION FOR EACH PARAMETER : Parameter Forward Voltage Peak Emission Wave Length Spectral Line Half-Width Reverse Current Average Luminous Intensity Symbol Vf λρ ∆λ Ir Iv Unit V nm nm µA µ cd Test Condition If=20mA If=20mA If=20mA Vr=5V If=10mA 3 4 5 6 7 8 PART NO. SELECTION AND APPLICATION INFORMATION (RATINGS AT 25 C AMBIENT) Chip Part No. Raw Material GaP GaAsP/GaP GaAlAs GaP GaP GaAsP/GaP GaP Emitted Color Bright Red Hi-Eff Red Super Red Green Super Green Yellow Bright Red Hi-Eff Red Super Red Green Super Green Yellow Common Cathode Common Anode C.C or C.A Wave Length λρ (nm) 700 635 660 565 570 585 700 635 660 565 570 585 Absolute Maximum Ratings ∆λ Pd If Electro-optical Characteristic o If If Vf (V) Iv (µcd) (Peak) (Rec) Per Dot Per Dot (nm) (mW) (mA) (mA) Min. Typ. Max. mA Min. Typ. 90 45 20 30 30 30 90 45 20 30 30 30 100 100 100 100 100 100 100 100 100 100 100 100 50 50 50 50 50 50 50 50 50 50 50 50 100 100 100 100 100 100 100 100 100 100 100 100 1.7 1.7 1.5 1.7 1.7 1.7 1.7 1.7 1.5 1.7 1.7 1.7 2.4 1.9 1.9 2.2 2.2 1.9 2.4 1.9 1.9 2.2 2.2 1.9 2.8 10-20 450 2.6 10-20 900 950 1800 KWM-30881A5 KWM-30881A3 KWM-30881AS KWM-30881A2 KWM-30881AG KWM-30881A6 KWM-30881C5 2.6 10-20 1600 3000 2.6 10-20 800 2.6 10-20 850 2.6 10-20 800 2.8 10-20 450 2.6 10-20 900 1700 1850 1700 950 1800 KWM-30881C3 GaAsP/GaP KWM-30881CS KWM-30881C2 KWM-30881CG GaAlAs GaP GaP 2.6 10-20 1600 3000 2.6 10-20 800 2.6 10-20 850 2.6 10-20 800 1700 1850 1700 KWM-30881C6 GaAsP/GaP REMARKS : 1. The average luminous intensity is obtained by summing the luminous intensity of each segment and dividing by the total number of segments. 2. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE (International Commission on Illumination) eye-response curve. 3. Clean only by pure water, isopropanol, ethanol, Freon TF (or equivalent).