NT200

L U M I N IS 1 2 Wall & Pedestal mount Specification NAUTILUX NT200 . NT200PK All exposed cast aluminum components are made of non corrosive pure aluminum copper free (Aluminum is less than .1% copper content.#356 alloy.) Finish: All polyester powder baked coatings preceded with a 5 baths preparation process. Meets military grade MIL-C781706 with a 2000 hours salt spray test. - Pulse rated medium base porcelain socket. - 75W/600V thermoplastic compact fluorescent socket. - One-piece molded silicone gasket with memory retention. - High power factor CWA ballast. Or 98% P.F.electronic smart ballast with end of life detection for compact fluorescent. - All stainless steel hardware. - All Moving and removable parts are sealed with a memory retention silicone gasket. 1- Closed cast aluminum housing. 2- Set of three cast aluminum interlocked louver blades. 3- Borosilicate frosted glass diffuser with internal concentric reinforcement prismatic pattern. 4- One piece cast aluminum front light shield. 5- Semi-specular aluminum reflector, with horizontal lamp position to provide uniform light on the diffuser. 3 4 5 11 ” 12 1/2” Photometry 12 1/2” Cross view 24” min. AFF Plane view NT200 Front view 90 Separate updated technical specification sheets with related models and light sources with I.E.S formatted photometry are available on www.luminis.com. pedestal mount. Min.24” above grade NT200 PK 60 30 Certification UL. Wet Location. Mounting Max. Max. weight: 27 lbs. Installation: Mounts over a standard 4” octagonal electrical box with 3 1/2” c/c mounting holes. For options details and specifications, please refer to page 72 Model# Light source selection Voltage 120 V Standard factory prewired (If no voltage is specified) For other voltages, please specify with catalog number. H.I.D. 208 V 240 V 277 V 347 V Note: 50W.HPS is available with 120/277V only. Finish (Refer to color chart) Standard selection WHT:Snow white BKT: Jet black BZT : Bronze GRT: Titanium gray DGT: Gun metal CHT: Champagne MST: Matte silver GNT: Forest green Optional colors CS: Custom color RAL: RAL# color PC1 : Options Accessories Polycarbonate lens diffuser. (Max.50W) Electrical 1 lamp (26/32/42W) Fuse 120V photo cell 208/277V photo cell Standby lamp socket. H.I.D. lamp restrike MH (ED17) M50 M70 M100 HPS (ED17) H50 H70 H100 CF (Gx24q) Single lamp F118 F126 F132 F142 CF (Gx24q) Two lamps F218 F226 F232 F242 NT200 NT200PK EM42S: FS: PH1 : PH2 : QS: QRS: COMP. FLUO. Smart ballast 120/277 347 V (To specify) Note: EM optional battery test switch and pilot lamp are remotely installed. INC. (A19) A100 (Lamps by others) Luminaires may be altered for design improvements or discontinued without prior notice. LUMINIS [ USA ] - 3555 NW 53rd Court, Fort Lauderdale, FL.33309 LUMINIS [ Canada ] - 87 C Brunswick D.D.O. Q.C. Canada H9B 2J5 Tel: 954 .717 .4155 Fax: 954 . 717.4157 Web: www.luminis.com Sept. 2006 Rev. Feb.2008 Toll free: 888 .401 .6999 Page 58 L U M IN I S OPTIONAL ACCESSORIES NAUTILUX General notes: Please specify selected option as a suffix to the specified model number. ex:NT100-M100-WHT-PC1 Each model is provided with a listing of compatible options.Some options may not be compatible when used in the same luminaire. This information is indicated when it is applicable. Square lens Diffuser. Option: PC6 Surface connection box Option: SWK White translucent round diffuser. Option: PC1 Alternate regressed reflector. Option: R2 High impact acrylic lens diffuser. Max: 50W 1 1/2" deep luminaire matching connection box for surface conduit feed. (2) 7/8" dia. K.O. @ 180 deg. Polycarbonate lens diffuser Max: 50W Satin anodized corrugated reflector surface. Quartz lamp restrike Option: QRS Quartz restrike standby lamp kit max.100w DC bayonet type Ceiling surface mounting Option: C White translucent round diffuser. Option: PC2 White translucent oblong diffuser. Option: PCO I n line fuse Option: FS 3 Amps. in line protection fuse, factory installed with the pole or inside fixture when pole is not required. Ceiling surface mount conversion kit. Maximum wattage 2x32w compact fluorescent. (factory installed.) High impact acrylic lens diffuser. Max: 50W Polycarbonate lens diffuser Max: 50W Light photo sensor Option: PH1 -120V PH2 - 208/277V Photo electric sensor, factory installed with the pole or inside fixture when pole is not required. Emergency line quartz lamp Option: QS Quartz lamp socket for separate emergency line. Max.100w DC bayonet type EM42 wiring HOT ns W) Emergency battery back-up EM42 / EM42S One lamp: 26w: 450 Lmns.. 32w: 575 Lmns. 42w: 750 Lmns. Time: 90 Mnts -120/277V / T 0º C COM EM42S wiring BLK WHT AC ballast Note: EM42 option is supplied with integral test switch and pilot light. EM42S is supplied with additional wiring for external remotely installed test switch and pilot light. Please refer to luminaire specification sheet option listing. W) cell cket. ike EM Ballast wiring diagram for 120V factory connection. WHT EM ballast For 57w & 70w: (Remote installation only) Consult factory Black/120V (Factory wired) Orange/277V (Cap unused lead.) Single pole test switch (Breaking the connection) Luminaires may be altered for design improvements or discontinued without prior notice. LUMINIS [ USA ] - 3555 NW 53rd Court, Fort Lauderdale, FL.33309 LUMINIS [ Canada ] - 87 C Brunswick D.D.O. Q.C. Canada H9B 2J5 Tel: 954 .717 .4155 Fax: 954 . 717.4157 Toll free: 888 .401 .6999 Web: www.luminis.com Sept. 2006 Rev. Feb.2008 Page 72