MASW-003100-11920W

MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Features ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ Broad Bandwidth Specified from 50MHz to 20GHz Usable from 50MHz to 26.5GHz Lower Insertion Loss / Higher Isolation than pHempt Rugged Fully Monolithic, Glass Encapsulated Construction Up to +33dBm C.W. Power Handling Rev. V6 MASW-001100-1190 Description The MASW-001100-1190, MASW-002100-1191 and MASW-003100-1192 are broadband monolithic switches using series and shunt connected silicon PIN diodes. They are designed for use as 2W, high performance switches in applications up to 26.5GHz. They provide performance levels superior to those realized by hybrid MIC designs incorporating beamlead and PIN chip diodes that require chip and wire assembly. These switches are fabricated using M/A-COM’s patented HMICTM (Heterolithic Microwave Integrated Circuit) process, US Patent 5,268,310. This process allows the incorporation of silicon pedestals that form series and shunt diodes or vias by imbedding them in low loss, low dispersion glass. By using small spacing between elements, this combination of silicon and glass gives HMIC devices low loss and high isolation performance through low millimeter frequencies. Large bond pads facilitate the use of low inductance ribbon leads, while gold backside metallization allows for manual or automatic chip bonding via 80/20, AuSn solder or conductive Ag epoxy. Parameter Operating Temperature Storage Temperature Junction Temperature Applied Reverse Voltage RF C.W. Incident Power Bias Current +25°C Absolute Maximum -65oC to +125oC -65oC to +150oC +175oC | - 50V | +33dBm C.W. ±20mA MASW-002100-1191 MASW-003100-1192 Max operating Conditions for a Combination of RF Power, D.C. Bias and Temperature: +33dBm CW @ 15mA (per diode) @+85°C 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant MASW-001100-1190 (SPST) Electrical Specifications @ TA = +25oC, 20mA Bias Parameter Insertion Loss Rev. V6 Frequency 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 1GHz Minimum 46 39 34 22 15 14 - Nominal 0.4 0.5 0.7 55 47 42 31 33 27 20 0.2 Maximum 0.7 0.9 1.2 50 - Units dB dB dB dB dB dB dB dB dB ns V dB Isolation Input Return Loss Switching Speed1 Voltage Rating2 Signal Compression (500mW) MASW-002100-1191 (SPDT) Electrical Specifications @ TA = +25oC, 20mA Bias Parameter Insertion Loss 1.) Typical Switching Speed measured from 10 % to 90 % of detected RF signal driven by TTL compatible drivers. 2.) Maximum reverse leakage current in either the shunt or series PIN diodes shall be 10mA maximum at -50 volts. Frequency 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 1GHz Minimum 48 40 34 20 18 15 - Nominal 0.4 0.5 0.7 63 50 42 27 25 25 20 0.2 Maximum 0.7 1.0 1.2 50 - Units dB dB dB dB dB dB dB dB dB ns V dB Isolation Input Return Loss Switching Speed1 Voltage Rating2 Signal Compression (500mW) MASW-003100-1192 (SP3T) Electrical Specifications @ TA = +25oC, 20mA Bias Parameter Insertion Loss 1.) Typical Switching Speed measured from 10 % to 90 % of detected RF signal driven by TTL compatible drivers. 2.) Maximum reverse leakage current in either the shunt or series PIN diodes shall be 10mA maximum at -50 volts. Frequency 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 6GHz 13GHz 20GHz 1GHz Minimum 49 42 33 20 14 11 - Nominal 0.5 0.7 0.9 57 48 42 24 22 21 20 0.2 Maximum 0.8 1.1 1.5 50 - Isolation Input Return Loss Switching Speed1 Voltage Rating2 Signal Compression (500mW) 2 Units dB dB dB dB dB dB dB dB dB ns V dB ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Typical Performance Curves at TA = +25°C, 20mA Bias Current MASW-001100-1190 RETURN LOSS vs. FREQUENCY -10 -15 -0.2 Rev. V6 MASW-001100-1190 INSERTION LOSS vs. FREQUENCY INSERTION LOSS (dB 30 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 RETURN LOSS (dB) Output Return Loss -20 -25 -30 -35 0 5 10 15 20 25 Input Return Loss 0 5 10 15 20 25 30 FREQUENCY (GHz) FREQUENCY (GHz) MASW-002100-1191 RETURN LOSS vs. FREQUENCY -10 MASW-002100-1191 INSERTION LOSS vs. FREQUENCY -0.2 -15 INSERTION LOSS (dB -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 RETURN LOSS (dB) Output Return Loss -20 -25 -30 Input Return Loss - 35 0 5 10 15 20 25 30 0 5 10 15 20 25 30 FREQUENCY (GHz) FREQUENCY (GHz) MASW-003100-1192 RETURN LOSS vs. FREQUENCY -10 MASW-003100-1192 INSERTION LOSS vs. FREQUENCY -0.3 INSERTION LOSS (dB -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1 -1.1 -1.2 RETURN LOSS (dB ) -15 Output Return Loss -20 -25 Input Return Loss -30 0 5 10 15 20 25 30 0 5 10 15 20 25 30 FREQUENCY (GHz) FREQUENCY (GHz) S-Parameters: S-Parameter data for these devices are available upon request. 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Typical Performance Curves @ TA = +25°C, 20mA Bias Current MASW-001100-1190 ISOLATION vs. FREQUENCY -35 -40 Rev. V6 INPUT RETURN LOSS vs. BIAS CURRENT @ 10 GHz -22 INPUT RETURN LOSS (dB -24 -26 -28 -30 -32 - 34 0 5 10 15 20 25 30 35 40 45 50 55 MA S W-0 0 110 0 MA S W-0 0 3 10 0 ISOLATION (dB) -45 -50 -55 -60 -65 -70 -75 - 80 0 5 10 15 20 25 30 MA S W-0 0 2 10 0 CURRENT (mA ) OUTPUT RETURN LOSS vs. BIAS CURRENT@ 10 GHz OUTPUT RETURN LOSS (dB -21.5 -22 -22.5 -23 -23.5 -24 -24.5 -25 - 25.5 0 5 10 15 20 25 30 35 40 45 50 55 MA S W-0 0 3 10 0 MA S W-0 0 2 10 0 MAS W-0 0 110 0 FREQUENCY (GHz) MASW-002100-1191 ISOLATION vs. FREQUENCY -35 -40 ISOLATION (dB) -45 -50 -55 -60 -65 -70 CURRENT (mA ) INSERTION LOSS vs. BIAS CURRENT @ 10 GHz -0.35 INSERTION LOSS (dB -75 -80 0 5 10 15 20 25 30 -0.4 -0.45 -0.5 -0.55 -0.6 -0.65 - 0.7 0 5 10 15 20 25 30 35 40 MAS W-0 0 2 10 0 MAS W-0 0 110 0 FREQUENCY (GHz) MAS W-0 0 3 10 0 MASW-003100-1192 ISOLATION vs. FREQUENCY -35 -40 45 50 55 CURRENT (mA) ISOLATION (dB) -45 -50 -55 -60 -46 -47 ISOLATION vs. BIAS CURRENT @ 10 GHz ) ISOLATION (dB -65 -70 -75 - 80 0 5 10 15 20 25 30 -48 -49 -50 -51 -52 -53 - 54 0 5 10 15 20 25 30 35 40 45 50 55 MAS W-0 0 2 10 0 MAS W-0 0 3 10 0 MAS W-0 0 110 0 FREQUENCY (GHz) CURRENT (mA) 4 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Operation of the MASW Series Switches Operation of the MASW series of PIN switches is achieved by simultaneous application of negative DC current to the low loss switching arm J1, J2, or J3, and positive DC current to the remaining switching arms as shown in the bias connection circuits. DC return is achieved via J1. The control currents should be supplied by constant current sources. The voltages at these points will not exceed +1.5 volts (1.2V typical) at currents up to +20mA. In the low loss state, the series diode must be forward biased and the shunt diode reverse biased. In the isolated arm, the shunt diode is forward biased and the series diode is reverse biased. J1 RF INPUT Rev. V6 MASW-001100-1190 and Bias Connections1 20pF 20nH J2 BIAS 20pF 100Ω 20nH 20pF 20pF Switch Chip J2 RF OUTPUT Driver Connections MASW-001100-1190 Control Level (DC Current) at J2 -20mA +20mA Condition of RF Output J1-J2 Low Loss Isolation MASW-002100-1191 and Bias Connections1 J1 RF INPUT 20pF J3 BIAS 20nH J2 BIAS MASW-002100-1191 Control Level (DC Current) at J2 -20mA +20mA J3 +20mA -20mA 100Ω 20nH 20pF 20pF 20nH 20pF Condition of RF Output J1-J2 Low Loss Isolation Condition of RF Output J1-J3 Isolation Low Loss 20pF J3 RF OUTPUT Switch Chip 20pF J2 RF OUTPUT MASW-003100-1192 Control Level (DC Current) at J2 -20mA +20mA +20mA J3 +20mA -20mA +20mA J4 +20mA +20mA -20mA MASW-003100-1192 and Bias Connections1 J1 RF INPUT 20pF J4 BIAS 20nH J2 BIAS Cond. of Cond. of Cond. of RF RF Output RF Output Output J1-J2 Low Loss Isolation Isolation J1-J3 Isolation Low Loss Isolation J1-J4 Isolation Isolation Low Loss 20pF 20nH 20pF 100Ω 20nH 20pF 20pF J4 RF OUTPUT 20pF J2 RF OUTPUT Handling Considerations Cleanliness: These chips should be handled in a clean environment. Electro-Static Sensitivity: The MASW series PIN switches are ESD, Class 1A sensitive (HBM). The proper ESD handling procedures should be used. 20pF 20nH J3 BIAS 20pF J3 RF OUTPUT Notes: 1. RLC values are for an operation frequency of 2-18GHz and bias current of ± 20mA per diode. 5 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Wire Bonding Thermosonic wedge wire bonding using 0.003” x 0.00025” ribbon or 0.001” diameter gold wire is recommended. A heat stage temperature of approximately 200oC and a force of 18 to 22 grams should be used. Ultrasonic energy should be adjusted to the minimum required to achieve a good bond. RF bond wires should be kept as short as possible. Rev. V6 Mounting The HMIC switches have TiPtAu back metal. They can be die mounted with a gold-tin eutectic solder preform or conductive epoxy. Mounting surface must be clean and flat. Eutectic Die Attachment: An 80/20 gold-tin eutectic solder preform is recommended with a work surface temperature of 255oC and a tool tip temperature of 265oC. When hot gas is applied, the tool tip temperature should be 290oC. The chip should not be exposed to temperatures greater than 320oC for more than 20 seconds. No more than three seconds should be required for attachment. Solders containing tin should not be used. Epoxy Die Attachment: Surface of assembly should be preheated to 125-150oC. A minimum amount of epoxy should be used. A thin epoxy fillet should be visible around the perimeter of the chip after placement. Cure epoxy per manufacturer’s schedule. Chip Outline Drawing1,2 DIM INCHES MIN. MAX. 0.018 0.029 MIN. 0.35 0.64 MM MAX. 0.45 0.74 A B C D E F G H 0.014 0.025 0.008 REF 0.004 0.006 0.20 REF 0.10 0.15 0.004 REF 0.003 REF 0.003 REF 0.020 REF 0.10 REF 0.08 REF 0.08 REF 0.52 REF Notes: 1. Topside and backside surface metallization is gold, 2.5μm thick typical. 2. Yellow areas indicate wire bonding pads. 6 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Rev. V6 Chip Outline Drawing1,2 MASW-002100-1191 DIM MIN. A B C D E F G H 0.029 0.004 INCHES MAX. 0.033 0.006 MIN. 0.73 0.10 MM MAX. 0.83 0.15 0.10 REF 0.13 REF 0.23 REF 0.58 REF 0.17 REF 0.10 REF 0.004 REF 0.005 REF 0.009 REF 0.023 REF 0.007 REF 0.004 REF Notes: 1. 2. Topside and backside surface metallization is gold , 2.5μm thick typical. Yellow areas indicate wire bonding pads 7 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Rev. V6 Chip Outline Drawing 1, 2 MASW-003100-1192 DIM MIN. A B C D E F G H J INCHES MAX. MIN. 0.046 0.050 0.036 0.040 0.019 REF 0.014 REF 0.004 REF 0.005 REF 0.004 0.006 0.005 REF 0.004 REF MM MAX. 1.16 1.26 0.92 1.02 0.48 REF 0.36 REF 0.10 REF 0.13 REF 0.10 0.15 0.12 REF 0.10 REF Notes: 1. Topside and backside surface metallization is gold , 2.5μm thick typical. 2. Yellow areas indicate wire bonding pads 8 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-001100-1190 MASW-002100-1191 MASW-003100-1192 HMIC™ Silicon PIN Diode Switches RoHs Compliant Rev. V6 Ordering Information Part Number MASW-001100-11900W MASW-001100-11900G MASW-002100-11910W MASW-002100-11910G MASW-003100-11920W MASW-003100-11920G Package Waffle Pack Gel Pack Waffle Pack Gel Pack Waffle Pack Gel Pack 9 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.