MASWSS0100-DIE

MASWSS0100 GaAs SP3T 2.5 V High Power Switch 0.1 - 3.0 GHz Features • • • • • • Low Voltage Operation: 2.5V Low Harmonics: -70 dBc at +34 dBm & 1 GHz Low Insertion Loss: 0.5 dB at 1 GHz High Isolation: 20 dB at 2 GHz 0.5 micron GaAs PHEMT Process Supplied as Known Good Die Rev. V2 Die Bond Pad Layout V1 RFC V3 Description M/A-COM’s MASWSS0100 is a GaAs PHEMT MMIC single pole three throw (SP3T) high power switch die. The MASWSS0100 is ideally suited for applications where high power, low control voltage, low insertion loss, high isolation, small size and low cost are required. Typical applications are for GSM, DCS and PCS handset systems that connect separate transmit and receive functions to a common antenna, as well as other handset and related applications. This part can be used in all systems operating up to 2.5 GHz requiring high power at low control voltage. The MASWSS0100 is fabricated using a 0.5 micron gate length GaAs PHEMT process. The process features full passivation for performance and reliability. RF1 RF2 V2 RF3 Pad Configuration Pad Name V1 RF1 RF2 Description Control 1 RF Port 1 RF Port 2 Control 2 RF Port 3 Control 3 Antenna/Common Port Ordering Information1 Part Number MASWSS0100-DIE 1. Die quantity varies. V2 RF3 V3 RFC Product Description Separated Die on Grip Ring1 Absolute Maximum Ratings 2,3 Parameter Input Power Voltage Operating Temperature Storage Temperature Absolute Maximum +38 dBm ± 8.5 volts -40°C to +85°C -65°C to +150°C 2. Exceeding any one or combination of these limits may cause permanent damage to this device. 3. M/A-COM does not recommend sustained operation near these survivability limits. 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0100 GaAs SP3T 2.5 V High Power Switch 0.1 - 3.0 GHz Electrical Specifications: TA = 25°C, VC = 0 V / 2.5 V, Z0 = 50 Ω 4 Parameter Insertion Loss 5 Isolation Return Loss P.1dB 2 nd rd Rev. V2 Test Conditions 0.5 - 1.0 GHz 1.0 - 2.0 GHz 0.5 - 1.0 GHz 1.0 - 2.0 GHz 0.5 - 2.5 GHz — 1.0 GHz, PIN = +34 dBm 1.0 GHz, PIN = +34 dBm 10% to 90% RF, 90% to 10% RF 50% control to 90% RF 50% control to 10% RF In Band 2.5 V Units dB dB dB dB dB dBm dBc dBc nS nS mV µA Min. — — 23 — — — — — — — — — Typ. 0.5 0.6 25 20 20 38 -80 -70 83 94 58 50 Max. 0.65 — — — — — — -65 — — — 80 Harmonic 3 Harmonic Trise, Tfall Ton, Toff Transients Control Current 4. External DC blocking capacitors are required on all RF ports. 5. Insertion loss can be optimized by varying the DC blocking capacitor value, e.g. 1000 pF for 100 MHz - 1 GHz, 39 pF for 0.5 - 3 GHz. Functional Diagram RFC V1 RF1 V3 Truth Table 6,7 V1 1 0 0 V2 0 1 0 V3 0 0 1 RFC– RF1 On Off Off RFCRF2 Off On Off RFC RF3 Off Off On 6. State 0 = -5 V to +2.5 V, State 1 = -2.5 V to +5 V. 7. Differential voltage, V (state 1) - V (state 0), must be 2.5 V minimum. Qualification Qualified to M/A-COM specification REL-201, Process Flow –2. Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. RF2 RF3 V2 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASWSS0100 GaAs SP3T 2.5 V High Power Switch 0.1 - 3.0 GHz Typical Performance Curves Insertion Loss vs. Frequency 1.0 IL+25°C IL+85°C IL-40°C Rev. V2 Isolation vs. Frequency 40 0.8 30 0.6 20 0.4 10 0.2 IL +25°C IL +85°C IL -40°C 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Frequency (GHz) Frequency (GHz) 2nd Harmonic vs. VC -40 25°C 85°C -40°C 3rd Harmonic vs. VC -40 25°C 85°C -40°C -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -100 2.0 2.5 3.0 3.5 4.0 4.5 5.0 V (V) C V (V) C 3 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, • Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. • Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.