1EJT1_1

CORCOM Product Guide Compact RFI Filter with IEC Connector for Higher Frequency Applications EJT Series UL Recognized CSA Certified VDE Approved* EJT1 EJT8 EJT Series The EJT Series is a power inlet filter designed to attenuate noise up to 1 GHz. This inlet uses an IEC 320/C14 input connector which gives it a maximum rating of 15 amps. The EJT series is flange-mounted with optional outputs of 1/4" terminals or wire leads. This product was designed to address the demand for more noise attenuation at higher frequencies in a compact inlet. Now also available with an IEC 320/C20 connector with a maximum rating of 20 amps. *15EJT - VDE rated at 10 amps, 250 VAC 20EJT - VDE rated at 16 amps, 250 VAC Specifications Maximum leakage current,each line-to-ground 1-15 Amp @ 120 VAC 60 Hz: .22 mA @ 250 VAC 50 Hz: .38 mA Hipot rating (one minute): line-to-ground 2250 VDC line-to-line 1450 VDC Operating frequency: Rated voltage (max.): Minimum insertion loss in dB: Line-to-ground in 50 ohm circuit Current Rating 01A 03A 06A 10A 15A 20A .15 27 22 13 7 4 .5 33 30 21 14 10 8 Frequency-MHz 1 5 10 40 59 65 34 57 63 27 51 60 21 43 52 15 38 48 15 42 50 30 65 69 65 61 63 60 20 Amp .20 mA .40 mA 1500 VAC 1450 VDC 50/60 Hz 250 VAC Electrical Schematics 1-15 Amp LINE LOAD 100 61 61 59 61 63 58 1000 14 10 14 14 14 14 Line-to-line in 50 ohm circuit Current Rating 01A 03A 06A 10A 15A 20A .15 10 10 10 10 10 9 .5 20 20 21 21 20 20 Frequency-MHz 1 5 10 23 43 52 51 24 41 24 37 48 25 28 44 26 25 36 26 40 35 30 65 59 65 63 56 48 100 45 52 55 53 45 50 1000 14 17 20 18 23 10 20 Amp Resistor location for reference only. 52 Catalog 1654001 Revised 05-07 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA Cust. Svc.: 1-800-468-2023 CORCOM Prods: 1-847-680-7400 Germany: 49-89-6089-0 www.corcom.com www.tycoelectronics.com CORCOM Product Guide Compact RFI Filter with IEC Connector for Higher Frequency Applications (Continued) EJT Series RFI Power Line Filters Case Styles EJT1 Case Dimensions A B (max) (max) 2.87 72.9 2.23 56.6 3.8 96.52 3.2 81.28 1.19 30.2 1.19 30.2 1.350 34.29 1.350 34.29 C D E F (max) (max) (max) (max) 0.875 22.2 0.875 22.2 1.18 29.99 1.18 29.99 1.575 40.0 1.575 40.0 1.654 42.01 1.654 42.01 1.98 — 50.3 1.98 0.295 50.3 7.5 2.087 — 53.00 2.087 — 53.00 Part No. C 1-15A EJT1 B D E A 1-15A EJT8 20EJT1 4.0 101.6 F EJT8 20EJT8 B F E D Part Numbers C A Typical dimensions: Wire Leads: 4.0 [101.6] Min. - 18 AWG 01EJT1 03EJT1 06EJT1 10EJT1 15EJT1 20EJT1 Line Cord No. 01EJT8 03EJT8 06EJT8 10EJT8 15EJT8 20EJT8 GA400 20EJT1 Recommended Panel Cutout D A B 1 to 15 Amp ∅ .140 3.56 C 0.126 Dia. with 0.236 x 90° Countersink for #4 Flat Head Screw (2X) 1.035 [26.29] 0.650 16.51 max. E 0.25 Terminal with 0.069 (± .003) dia. hole (2 places) .820 20.83 1.200 30.48 1.575 40.00 Panel Cutout (front mount) Tolerance ±.005 [0.13] 0.005 Tolerance +/Panel Cutout (Front Mount) E Label 0.25 Terminal with 0.069 x 0.155 Slot R .062 1.57 20EJT8 20 Amp D A 4.0 101.6 min. E 0.138 Dia. (2X) 3.51 R 0.118 3.00 C 1.035 [26.29] 1.055 26.80 0.528 13.41 0.126 Dia. with 0.236 x 90° Countersink for #4 Flat Head Screw (2X) Wire, #14 AWG UL 1015 (3 places) B 1.370 34.80 E Label Brown (Line) Green / Yellow (Ground) Blue (Neutral) 1.654 42.01 Panel Cutout (front mount) Tolerance ±.005 [0.13] 53 Catalog 1654001 Revised 05-07 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. USA Cust. Svc.: 1-800-468-2023 CORCOM Prods: 1-847-680-7400 Germany: 49-89-6089-0 www.corcom.com www.tycoelectronics.com