V23079-E1202-B301

The Best Relaytion P2 Relay ISO 9001 P2 Relay 2 pole telecom relay, polarized, Through Hole Type (THT) or Surface Mount Technology (SMT), Relay types: non-latching with 1 coil latching with 2 coils latching with 1 coil V23079 Features – Standard telecom relay (ringing and test access) – Slim line 15 x 7.5 mm, 0.590 x 0.295 inch – Switching current 5 A – 2 changeover contacts (2 form C / DPDT) – Bifurcated contacts – Immersion cleanable – High sensitivity results in low nominal power consumption 140 mW for non-latching and latching with 2 coils 70 mW for latching with 1 coil – For single coil version: - Surge voltage resistance between contact and coil for single coil version: - 2.5 kV (2 / 10 µsec) meets the Bellcore Requirement GR-1089 - 1.5 kV (10 / 160 µsec) meets FCC Part 68 Typical applications – Communications equipment linecard application (ringing and test access) PABX Voice over IP – Office equipment – Measurement and control equipment – Automotive equipment CAN bus, keyless entry, speaker switch – Medical equipment – Consumer electronics Set Top Boxes, HiFi Options – 1500 Vrms between open contacts – Temperature range up to 105° C IEC/EN60950 IEC Ref. Cert. No. CH 2171 Insulation category: UL 508 UL 60950 File No. E111441 Supplementary insulation according IEC / EN 60950 Working voltage ³ 300 Vrms Mains supply voltage ³ 250 Vrms Repetitive peak voltage 2500 V Pollution degree: Internal: 1 External: 2 Flammability classification: V-0 Maximum operating temperature: 85 °C CECC 811-54-003 QC 160504-CH0003 2 P2 Relay Dimensions THT V23079-x1xxx-B301 standard coil mm inch L 14.5 ± 0.1 W 7.2 ± 0.1 H 9.8 ± 0.1 T 3.25 - 0.25 T1 N/A T2 N/A Tw 0.5 ± 0.05 S 0.55 - 0.15 0.570 ± 0.004 0.283 ± 0.004 0.385 ± 0.004 0.128 -0.010 N/A N/A 0.020 ±0.002 0.022 -0.006 V23079 THT V23079-x2xxx-B301 overmolded coil mm inch 14.5 ± 0.1 7.2 ± 0.1 9.5 ± 0.1 3.25 - 0.25 N/A N/A 0.5 ± 0.05 0.45 SMT long terminals V23079-x1xxx-B301 standard coil mm inch SMT long terminals SMT short terminals SMT short terminals V23079-x2xxx-B301 V23079-x1xxx-B301 V23079-x2xxx-B301 overmolded coil standard coil overmolded coil mm inch mm inch mm inch 0.570 ± 0.004 14.5 ± 0.1 0.283 ± 0.004 7.2 -0.15 0.374 ± 0.004 10.4 ± 0.15 0.128 -0.010 N/A N/A 5.52 ±0.15 N/A 9.4 ±0.15 0.020 ±0.002 0.5 ± 0.05 0.018 ±0.002 N/A 0.570 ± 0.004 14.5 ± 0.1 0.570 ± 0.004 14.5 ± 0.1 0.570 ± 0.004 14.5 ± 0.1 0.570 ± 0.004 0.283 ± 0.004 7.2 -0.15 0.283 ± 0.004 7.2 -0.15 0.283 ± 0.004 7.2 -0.15 0.283 ± 0.004 0.409 ±0.006 9.9 ± 0.1 0.390 ± 0.004 10.4 ± 0.15 0.409 ±0.006 9.9 ± 0.1 0.390 ± 0.004 N/A N/A N/A N/A N/A N/A N/A 0.217 ±0.006 5.52 0.217 ±0.006 5.52 0.217 ±0.006 5.52 0.217 ±0.006 0.370 ±0.006 9.4 ±0.15 0.370 ±0.006 7.4 ±0.15 0.291 ±0.006 7.4 ±0.15 0.291 ±0.006 0.020 ±0.002 0.5 ± 0.05 0.020 ±0.002 0.5 ± 0.05 0.020 ±0.002 0.5 ± 0.05 0.020 ±0.002 N/A N/A N/A N/A N/A N/A N/A THT Version SMT Version Long terminals Short terminals P2 SMT S Mounting hole layout View onto the component side of the PCB Solder pad layout Long terminals View onto the component side of the PCB Short terminals Note: Hole for pin 6 and 7 only for latching with 2 coils Basic grid 2.54 mm Note: Solder pad for pin 6 and 7 only for latching with 2 coils Note: Solder pad for pin 6 and 7 only for latching with 2 coils Terminal assignment Relay - top view Non-latching type, not energized condition Latching type, 1 coil reset condition Latching type, 2coils reset condition 3 P2 Relay Coil Data (values at 23°C) Nominal voltage Unom Operate/set voltage range Minimum voltage UI Vdc non-latching 1 coil 3 4 4.5 5 6 9 12 24* latching 2 coils 3 4.5 5 6 9 12 24 latching 1 coil 3 4.5 5 6 9 12 24 2.25 3.375 3.75 4.5 6.75 9.00 18.00 9.20 13.85 15.33 18.50 27.75 37.00 74.00 2.25 3.375 3.75 4.5 6.75 9.00 18.00 6.50 9.80 10.90 13.00 19.60 26.15 52.30 2.25 3.00 3.375 3.75 4.5 6.75 9.00 18.00 6.50 8.70 9.80 10.90 13.00 19.60 26.15 52.30 Vdc Maximum voltage UII Vdc V23079 Release/ reset voltage Minimum Nominal power consumption Resistance Coil number Vdc mW W / ± 10 % A1xxx/D1xxx/G1xxx A2xxx/D2xxx/G2xxx 0.30 0.40 0.45 0.50 0.60 0.90 1.20 2.40 140 140 140 140 140 140 140 140 64.3 114 145 178 257 578 1029 4114 008 016 011 001 002 006 003 005 B1xxx/E1xxx/H1xxx 2.25 3.375 3.75 4.50 6.75 9.00 18.00 140 140 140 140 140 140 140 64.3 145 178 257 578 1029 4114 208 211 201 202 206 203 205 C1xxx/F1xxx/J1xxx 2.25 3.375 3.75 4.50 6.75 9.00 18.00 70 70 70 70 70 70 70 128 289 357 514 1157 2057 8228 108 111 101 102 106 103 105 * 24 V only in A1xxx/D1xxx/G1xxx Further coil versions are available on request. UI = UII = Minimum voltage at 23° C after pre-energizing with nominal voltage without contact current Maximum continous voltage at 23° The operating voltage limits UI and UII depend on the temperature according to the formula: UI tamb = UII tamb = tamb UI tamb UII tamb kI, kII KI · UI and 23° C KIl · UIl 23° C = Ambient temperature = Minimum voltage at ambient temperature, tamb = Maximum voltage at ambient temperature, tamb = Factors (dependent on temperature), see diagram Ambient temperature tamb [°C] 4 P2 Relay Contact Data V23079 Number of contacts and type Contact assembly Contact material Limiting continuous current at max. ambient temperature Maximum switching current Maximum swichting voltage Maximum switching capacity Thermoelectric potential Minimum switching voltage Initial contact resistance / measuring condition: 10 mA / 20 mV Electrical endurance at 12 V / 10 mA at 6 V / 100 mA at 60 V / 500 mA at 30 V / 1000 mA at 30 V / 2000 mA Mechanical endurance UL contact ratings 2 changeover contacts Bifurcated contacts Silver nickel, gold-covered 2A 5A 220 Vdc 250 Vac 60 W, 62.5 VA < 10 mV 100 mV < 50 mW typ. 5 x 107 operations typ. 1 x 107 operations typ. 5 x 105 operations typ. 1 x 106 operations typ. 2 x 105 operations typ. 108 operations 220 Vdc / 0.24 A - 60 W 125 Vdc / 0.24 A - 30 W 250 Vac / 0.25 A - 62.5 VA 125 Vac / 0.5 A - 62.5 VA 30 Vdc / 2 A - 60 W Insulation resistance at 500 VDC Dielectric test voltage (1 min) between coil and contacts (Relay with 1 coil) between adjacent contact sets between open contacts Surge voltage resistance according to Bellcore TR-NWT-001089 (2 / 10 ms) between coil and contacts (Relay with 1 coil) between adjacent contact sets between open contacts according to FCC 68 (10 / 160 ms) between coil and contacts (Relay with 1 coil) between adjacent contact sets between open contacts Insulation > 109 W 1500 Vrms 1000 Vrms 1000 Vrms (1500 Vrms on request) 2500 V 2500 V 2000 V 1500 V 1500 V 1500 V High Frequency Data Capacitance between coil and contacts between adjacent contact sets between open contacts RF Characteristics Isolation at 100 / 900 MHz Insertion loss at 100 / 900 MHz V.S.W.R. at 100 / 900 MHz max. 2 pF max. 1.5 pF max. 1 pF - 39.0 dB / - 20.7 dB - 0.02 dB / - 0.27 dB 1.04 / 1.40 5 P2 Relay General data V23079 Operate time at Unom typ. / max. Reset time (latching) at Unom , typ. / max. Release time without diode in parallel (non-latching), typ. / max. Release time with diode in parallel (non-latching), typ. / max. Bounce time at closing contact, typ. / max. Maximum switching rate without load Ambient temperature Thermal resistance Maximum permissible coil temperature Vibration resistance (function) Shock resistance, half sinus, 11 ms Degree of protection / Environmental protection Needle flame test Mounting position Processing information Weight (mass) Resistance to soldering heat All data refers to 23° C unless otherwise specified. 3 ms / 5 ms 3 ms / 5 ms 2 ms / 4 ms 4 ms / 6 ms 1 ms / 3 ms 50 operations/s -40° C ... +85° C (105 ° C on request) < 165 K/W 110° C 35 G 10 to 1000 Hz 50 G (function) 150 G (damage) immersion cleanable, IP 67 / RT III application time 20 s, burning time < 15 s any Ultrasonic cleaning is not recommended max. 2.5 g 260° C / 10 s Recommended soldering conditions Soldering conditions according CECC 00802 10 sec 20 - 40 sec 215° C Temperature °C Temperature °C 180° C 130° C external preheating Full line: typical Dotted line: process limits max. 245° C 215° C 180° C 130° C ca. 40 sec 100° C forced cooling Full line: typical Dotted line: process limits Time (s) Time (s) Vapor Phase Soldering: Temperature/Time Profile (Lead Temperature) Infrared Soldering: Temperature/Time Profile (Lead Temperature) 6 P2 Relay Packing V23079 Dimensions in mm Tube for THT version - 50 relays per tube, 2000 relays per box Tape and reel for SMT version with long terminals - 400 relays per reel, 2000 relays per box 1,75 ±0,1 4 ±0,1 1,5 ±0,1 2 ±0,1 A Section A-A Section B-B 11,5 ±0,1 24 ±0,3 B B 3 max. 15,5 ±0,2 10 ±0,2 2,2 16 ±0,1 A 0,4 3 max. ECR0915-2 10,5 ±0,1 Tape and reel for SMT version with short terminals - 500 relays per reel, 2500 relays per box 1,5 ±0,1 2 ±0,1 1,75 ±0,1 4 ±0,1 A Section A-A Section B-B 11,5 ±0,1 24 ±0,3 B B 3 max. 15,5 ±0,2 8 ±0,2 3 max. ECR0917-I 1,5 ±0,1 A 10,5 ±0,2 0,4 12 ±0,1 Reel dimension 7 P2 Relay Ordering Information Relay Code V23079-A1001-B301 V23079-A1002-B301 V23079-A1003-B301 V23079-A1005-B301 V23079-A1006-B301 V23079-A1008-B301 V23079-A1011-B301 V23079-A2001-B301 V23079-A2002-B301 V23079-A2003-B301 V23079-A2005-B301 V23079-A2006-B301 V23079-A2008-B301 V23079-A2011-B301 V23079-B1201-B301 V23079-B1202-B301 V23079-B1203-B301 V23079-B1205-B301 V23079-B1206-B301 V23079-B1208-B301 V23079-B1211-B301 V23079-C1101-B301 V23079-C1102-B301 V23079-C1103-B301 V23079-C1105-B301 V23079-C1106-B301 V23079-C1108-B301 V23079-C1111-B301 V23079-D1001-B301 V23079-D1002-B301 V23079-D1003-B301 V23079-D1005-B301 V23079-D1006-B301 V23079-D1008-B301 V23079-D1011-B301 V23079-D2001-B301 V23079-D2002-B301 V23079-D2003-B301 V23079-D2006-B301 V23079-D2008-B301 V23079-D2011-B301 V23079 Tyco Part Number 0-1393788-3 0-1393788-8 1-1393788-1 1-1393788-6 2-1393788-0 2-1393788-2 2-1393788-4 3-1393789-5 3-1393789-6 3-1393789-7 0-1393790-2 3-1393789-8 6-1419120-6 3-1393789-9 3-1393788-3 3-1393788-5 3-1393788-6 3-1393788-7 3-1393788-9 4-1393788-1 4-1393788-2 4-1393788-5 4-1393788-7 4-1393788-8 5-1393788-0 5-1393788-1 5-1393788-3 5-1393788-4 5-1393788-5 5-1393788-6 5-1393788-7 5-1393788-8 5-1393788-9 6-1393788-1 6-1393788-2 4-1393789-3 4-1393789-4 4-1393789-5 4-1393789-6 4-1393789-7 4-1393789-8 Relay Code V23079-E1201-B301 V23079-E1202-B301 V23079-E1203-B301 V23079-E1205-B301 V23079-E1206-B301 V23079-E1208-B301 V23079-E1211-B301 V23079-F1101-B301 V23079-F1102-B301 V23079-F1103-B301 V23079-F1105-B301 V23079-F1106-B301 V23079-F1108-B301 V23079-F1111-B301 V23079-G1001-B301 V23079-G1002-B301 V23079-G1003-B301 V23079-G1005-B301 V23079-G1006-B301 V23079-G1008-B301 V23079-G1011-B301 V23079-G2001-B301 V23079-G2002-B301 V23079-G2003-B301 V23079-G2006-B301 V23079-G2008-B301 V23079-G2011-B301 V23079-H1201-B301 V23079-H1202-B301 V23079-H1203-B301 V23079-H1205-B301 V23079-H1206-B301 V23079-H1208-B301 V23079-H1211-B301 V23079-J1101-B301 V23079-J1102-B301 V23079-J1103-B301 V23079-J1105-B301 V23079-J1108-B301 V23079-J1111-B301 Tyco Part Number 6-1393788-8 0-1393789-5 6-1393788-9 7-1393788-0 0-1393789-9 7-1393788-1 7-1393788-2 7-1393788-3 1-1393789-0 7-1393788-4 1-1393789-1 1-1393789-2 7-1393788-5 1-1393789-4 7-1393788-6 1-1393789-5 7-1393788-7 7-1393788-8 1-1393789-6 8-1393788-0 1-1393789-7 4-1393789-9 5-1393789-0 5-1393789-1 5-1393789-3 5-1393789-4 5-1393789-5 2-1393789-0 2-1393789-1 8-1393788-3 2-1393789-2 2-1393789-3 2-1393789-4 8-1393788-4 2-1393789-5 2-1393789-6 2-1393789-7 2-1393789-8 2-1393789-9 3-1393789-0 Middle block of relay code V23079-yyxxx-B301 yy : See table below xxx : See coil table on page 4 yy A1 A2 B1 C1 Description THT, non latching, standard coil THT, non latching, overmolded coil THT, latching, 2 standard coils THT, latching, 1 standard coil D1 D2 coil E1 F1 G1 G2 coil H1 J1 SMT, long pins, non latching, standard coil SMT, long pins, non latching, overmolded SMT, long pins, latching, 2 standard coils SMT, long pins, latching, 1 standard coil SMT, short pins, non latching, standard coil SMT, short pins, non latching, overmolded SMT, short pins, latching, 2 standard coils SMT, short pins, latching, 1 standard coil 8 P2 Relay V23079 Option: high dielectric between open contacts (overmolded coil) This supplementary data sheet refers to the basic data sheet of the P2 relay series (V23079) with following additions: Dielectric strength 1500 Vrms between open contacts - as well as between coil and contacts and between adjacent contact sets Only non-latching types available SMT version with short terminals as preferred type mechanical and electrical endurance typ. 106 operations Dimensions SMT short terminals V23079-G2xxx-X0xx overmolded coil mm inch L 14.5 ± 0.1 W 7.2 -0.15 H 9.9 ± 0.1 T N/A T1 5.52 T2 7.4 ±0.15 Tw 0.5 ± 0.05 S N/A 0.570 ± 0.004 0.283 ± 0.004 0.390 ± 0.004 N/A 0.217 ±0.006 0.291 ±0.006 0.020 ±0.002 N/A SMT Version Short terminals Solder pad layout Note: Solder pad for pin 6 and 7 only for latching with 2 coils P2 SMT S Coil Data (values at 23°C) Nominal voltage Unom Operate/set voltage range Minimum voltage UI Vdc non-latching 1 coil 5 6 9 12 3.75 4.50 6.75 9.00 10.90 13.00 19.60 26.15 0.50 0.60 0.90 1.20 140 140 140 140 178 257 578 1029 Vdc Maximum voltage UII Vdc Vdc mW W / ± 10 % V23079G2001-X071 G2002-X072 G2006-X073 G2003-X074 Release/ reset voltage Minimum Nominal power consumption Resistance Relay code Ordering Information Relay Code V23079-G2001-X071 V23079-G2002-X072 V23079-G2006-X073 V23079-G2003-X074 Tyco Part Number 0-1422006-1 0-1422006-2 0-1422006-3 0-1422006-4 9 P2 Relay IM Relays V23079 D2n Relays 2nd generation non polarized 2 c/o relay for telecom and various other applications. Nominal voltage range from 3 ... 48 V, coil power consumption from 150 .... 500 mW. The D2n relay is capable to switch currents up to 3 A. Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 20 x10 mm board space and 11,5 mm height. 4th generation slim line – low profile polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 coil. Nominal voltage range from 1.5... 24 V, coil power consumption of 140... 200 mW, latching relays with 1 coil 100 mW. The IM relay is available as through hole and surface mount type (J-Legs and Gull Wings) and capable to switch loads up to 60 W/62,5 VA. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The IM relay is CECC/IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 10 x 6 mm board space and 5.65 mm height. P1 Relays P2 Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 or 2 coils. Nominal voltage range from 3 ... 24 V, coil power consumption 140 mW, latching relays with 1 coil 70 mW. The P2 Relay is available as through hole or surface mount type and capable to switch currents up to 5 A. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 15 x 7,5 mm board space and 10 mm height. Extremely sensitive, polarized 1 c/o relay with bifurcated contacts for a wide range of applications, available as non latching or latching relay with 1 or 2 coils. Nominal voltage range from 3 ... 24 V, coil power consumption 65 mW, latching relays with 1 coil 30 mW. The P1 relay is available as through hole or surface mount type and capable to switch currents up to 1 A. Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs). Dimensions approx. 13 x 7,6 mm board space and 7 mm height for THT or 8 mm height for SMT version. W11 Relays FX Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 coil. Nominal voltage range from 3 ... 48 V, coil power consumption of 80 ... 260 mW for the high sensitive version, 140... 300 mW for the standard version, latching relays with 1 coil 100 mW. The FX2 relay is available as through hole type and capable to switch loads up to 60 W/62,5 VA. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The FX2 is CECC/ IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 15 x 7,5 mm board space and 10,7 mm height. Low cost, non polarized 1 c/o relay for various applications. Nominal voltage range from 3 ... 24 V, coil power consumption 450 mW, sensitive versions 200 mW. The W11 relay is capable to switch currents up to 3 A. Dielectric strength 1000 Vrms. Dimensions approx. 15,6 x 10,6 mm board space and 11,5 mm height. Reed Relays FT2 / FU2 Relays High sensitive, non polarized relay for telecom and various other applications, available with 1 n/o, 2 n/o or 1c/o contacts. Nominal voltage range from 5 ... 24 V, coil power consumption 50...280 mW for 1 n/o and 125 ... 280 mW for 2 n/o or 1 c/o versions. Reedrelays are available in DIP or SIL housing and capable to switch currents up to 0,5 A. Integrated diode and/or electrostatic shield optional. Dielectric strength 1500 Vdc. Dimensions approx. 19,3 x 7 mm board space and 5 ... 7,5 mm height for DIP or 19,8 x 5 mm board space and 7,8 mm height for SIL version. 3rd generation non polarized, non latching 2 c/o telecom relay with bifurcated contacts. Nominal voltage range from 3 ... 48 V, coil power consumption 200 ... 300 mW. Most sensitive 48 V relay. Available as through hole and surface mount type. Dielectric strength fulfills the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) and FCC part 68 (1,5 kV – 10 / 160 µs). The FT2/FU2 is CECC/IECQ approved and certified in accordance with IEC/EN 60950 and UL1950. Dimensions approx. 15 x 7,5 mm board space and 10 mm height. Cradle Relays FP1 Relays 3rd generation polarized 2 c/o telecom relay with bifurcated contacts, available as non latching or latching relay with 1 or 2 coils. Nominal voltage range from 3 ... 48 V, coil power consumption of 80 ... 260 mW for the high sensitive version, 140... 300 mW for the standard version, latching relays with 1 coil 100 mW.. The FP1 Relay is available as through hole type and capable to switch loads up to 30 W/62,5 VA. Dielectric strength fulfills FCC part 68 (1,5 kV – 10 / 160 µs). The FP2 is CECC/IECQ approved. Dimensions approx. 14 x 9 mm board space and 5 mm height. Extremely reliable and mature relay family of 1st generation for various signal switching applications. Available as non polarized, polarized / latching and relay with AC coil. The benefit is the possibility of combining various contact sets from 1 up to 6 poles, single and bifurcated contacts, different contact materials with a coil voltage range from 1,5 Vdc to 220 Vac. Cradle relays are available as dust protected and hermetically sealed versions, with plug in or solder terminals and are capable to switch currents up to 5 A. Forcibly guided (linked) contact sets optional. Dielectric strength 500 Vrms. Dimensions from approx. 19 x 24 to 19x35 mm board space and 30 mm height. Other Relays MT2 / MT4 We offer a variety of different relay families for maintenance and replacement purposes. These relays are up to 60 years old now, such as Card Relay SN (V23030 / V23031 series), Small General Purpose Relay (V23006 series), Small Polarized Relay (V23063 ... V23067 and V23163 ... V23167 series). Accessories like sockets, hold down springs, etc. optional. 2nd generation non polarized, non latching 2 c/o and 4 c/o telecom and signal relay with bifurcated contacts. Nominal voltage range from 4.5 ... 48 V, coil power consumption 150/200/300/400 and 550 mW, and 300 mW (MT4). Dielectric strength fulfills the requirements according FCC part 68 (1,5 kV – 10 / 160 µs) for both and the Bellcore requirements according GR 1089 (2,5 kV – 2 / 10 µs) the MT4 only. Dimensions MT2 approx. 20 x 10 mm board space and 11 mm height, MT4 approx. 20 x15 mm board space and 11 mm height. HF3 Relay High performance low cost RF relay with excellent RF characteristics. Available with an impedance of 50 and 75 Ohm. Suitable for frequencies up to 3 GHz. Actually smallest RF relay available combining small size, excellent RF performance and SMD solderability. Available as non latching or latching relay with 1 or 2 coils and a nominal coil voltage range from 3 ... 24 V, coil power consumption 140 mW, latching relays with 1 coil 70 mW. Dimensions 14.6 x 7.3 x 10 mm. 10 Tyco Electronics AXICOM Ltd. Seestrasse 295 - P.O. Box 220 CH-8804 Au-Wädenswil / Switzerland Phone +41 1 782 9111 Fax +41 1 782 9080 E-mail: axicom@tycoelectronics.com Tyco Electronics AMP GmbH Paulsternstrasse 26 D-13629 Berlin / Germany Phone +49 30 386 38260 Fax +49 30 386 38569 E-mail: axicom@tycoelectronics.com Tyco Electronics EC Trutnov s.r.o. Komenského 821 CZ-541 01 Trutnov / Czech Republic E-mail: axicom@tycoelectronics.com Tyco Electronics Corporation POB 3608, Harrisburg, PA 17105, USA Phone +001 800-522-6752 11 February 2003 Rev. 2.08