205S12FR

www.make-ps.com E-mail:info@make-ps.com 200FR series FEATURES • • • • • Single & Dual Output DC/DC Converter Up to 61 % Efficiency Single and Dual Output, 2 watt converter Available in 5, 12, 24 and 48 VDC Inputs Industry Standard Pinout Short Circuit Protection DESCRIPTIONS The 200FR series 2 watt power modules are specially designed to provide low output ripple, and tight regulation in a low-profile 24 pin DIP package. The series consists of 20 models with input voltages of 5V, 12V, 24V and 48V, and offers regulated output voltages of 5V, 12V, 15V, ±12V and ±15V. The -25oC to +71oC operating temperature range makes it ideal for data communication equipment, mobile battery driven equipment, distributed power systems, telecommunication equipment, mixed analog/digital subsystems, automatic test instrumentation and industrial robot systems. INPUT CHARACTERISTICS Min Input Voltage 5 VDC Input Models 4.5 12 VDC Input Models 10.8 24 VDC Input Models 21.6 48 VDC Input Models 43.2 Input Fuse Requirements 5 VDC Input Models 12 VDC Input Models 24 VDC Input Models 48 VDC Input Models Reverse Polarity Input Current Short Circuit Input Power Input Filter Typ Max Unit/Comments 5 12 24 48 1500 700 350 135 5.5 13.2 26.4 52.8 VDC VDC VDC VDC OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Balance (Duals) Line Regulation Min Typ Max Unit/Comments ±2.0 ±4.0 % Output voltage at nominal line & FL ±1.0 ±3.0 % Equal Output Loads ±0.2 ±0.5 % Output voltage measured from min. input line to maximum ±0.2 ±0.5 % Output voltage measured from FL to 10% load 45 50 mV p-p, Nom.Line @FL, 20MHz B.W., using 1 μf bypass capacitor 75 mV p-p, Over Line, Load & Temp., 20 MHz B.W., using 1 μf bypass capacitor %Rated Output Load 120 Continuous, Automatic Recovery ±6 % deviation of Vout for a 50% load change 50 μS for 50% load change ±0.01 ±0.02 % per degree C mA; Slow blow type mA; Slow blow type mA; Slow blow type mA; Slow blow type 0.5 Amp 2000 mW Pi Filter GENERAL CHARACTERISTICS Switching Frequency Isolation Voltage Isolation Resistance Isolation Capacitance MTBF (MIL-HBK-217F) Min Typ Max Unit/Comments kHz 40 80 VDC, 1 minute 500 Mohm, 500VDC 1000 100 150 pF, 100kHz, 1Volt Thousand Hours, 800 +25oC, Ground Benign Load Regulation Ripple/Noise Ripple/Noise Overload Protection Short Circuit Protection Transient Response Deviation Transient Recovery Time Temperature Coefficient >> B-21 www.make-ps.com ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Operating Temp. Range Storage Temp. Range Relative Humidity Cooling Min -25 -25 -40 Typ Max +71 +90 +125 95 Unit/Comments o C; Ambient o C; Case o C % Humidity; noncondensing Free-Air Convection E-mail:info@make-ps.com PHYSICAL CHARACTERISTICS Case Size Case Material Flammability Weight Unit/Comments 1.25 X 0.8 X 0.4 inches (31.8 X 20.3 X 10.2 mm) Non-Conductive Black Plastic UL94V-0 12.1 Grams OUTLINE DRAWING 1.25 (31.8) 0.15 (3.8) SIDE VIEW 0.40 (10.2) 0.020(0.50) PIN DIA. 0.100 (2.54) 123 0.08 (2.0) 0.10 (2.5) 10 11 12 BOTTOM VIEW 24 23 22 15 14 13 0.600 0.80 (15.22) (20.3) PIN OUT CHART Pins Single 1 + Vin 2 NC 3 NC 10 - Vout 11 + Vout 12 - Vin 13 - Vin 14 + Vout 15 - Vout 22 NC 23 NC 24 + Vin NC = No Connection Dual + Vin - Vout Common Common + Vout - Vin - Vin + Vout Common Common -V out +V in Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 Pin : ±0.002 ±0.05 All specifications are typical at nominal input, nominal load and 25°C unless otherwise specified. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low ESR capacitor of 2.2mF for the 5V input devices, a 1.0mF for the 12V input devices and a 0.47mF for the 24V and 48V devices. >> B-22 www.make-ps.com HOW TO ORDER E-mail:info@make-ps.com HOW TO ORDER 2 15 Wattage Output Voltage Output Configuration (S=Single, D=Dual) D XX FR - Y ROHS Compliant Series Nominal Input Voltage MODEL SELECTION CHART Model 205S5FR 212S5FR 215S5FR 212D5FR 215D5FR 205S12FR 212S12FR 215S12FR 212D12FR 215D12FR 205S24FR 212S24FR 215S24FR 212D24FR 215D24FR 205S48FR 212S48FR 215S48FR 212D48FR 215D48FR Nominal Input Voltage (VDC) 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 48 48 48 48 48 Output Voltage (VDC) 5 12 15 ±12 ±15 5 12 15 ±12 ±15 5 12 15 ±12 ±15 5 12 15 ±12 ±15 Full Load Output Current (mA) 400 165 133 ±83 ±66 400 165 133 ±83 ±66 400 165 133 ±83 ±66 400 165 133 ±83 ±66 No Load Input Current (mA) 80 80 80 80 80 40 40 40 40 40 20 20 20 20 20 10 10 10 10 10 Full Load Input Current (mA) 800 730 690 740 770 330 295 265 280 280 163 135 135 135 135 83 70 70 80 80 Reflected Ripple Current (mA) 80 80 80 80 80 30 30 30 30 30 15 15 15 15 15 10 10 10 10 10 Efficiency (%) 50 54 57 53 51 50 56 62 59 59 51 61 61 61 61 50 59 59 51 51 >> B-23 www.make-ps.com DERATING CURVES E-mail:info@make-ps.com MODEL 200FR - 5V output only Pout % 100 90 80 70 60 50 40 30 20 10 0 -40 100LFM 200LFM Natural Convection 400LFM 50 60 70 80 90 100 110 TEMPERATURE ° C MODEL 200FR - all other outputs Pout % 100 90 80 70 60 50 40 30 20 10 0 -40 100LFM 200LFM Natural Convection 400LFM 50 60 70 80 90 100 110 TEMPERATURE ° C >> B-24