212S12HFR

www.make-ps.com E-mail:info@make-ps.com 200HFR series Single & Dual Output DC/DC Converter F EATURES • • • • • Up to 63% Efficiency Single & Dual Output, 2 watt converter 3000 VDC Input / Output Isolation Short Circuit Protection MTBF > 800,000 Hours DESCRIPTIONS The 200HFR series 2 watts power modules are high efficiency, low profile dc-dc converters that operate over input voltage ranges of 4.75-5.25 VDC, 10.8-13.2 VDC, and 21.6-26.4 VDC and provide precisely regulated output voltages of 5V, 12V, 15V, ±12V and ±15V. The -25oC to +71oC operating temperature range makes it ideal for data communication equipment, mobile battery driven equipment, distributed power systems, telecommunication equipment, mixed analog/digital subsystems, process/ machine control equipment, computer peripheral systems and industrial robot systems. INPUT CHARACTERISTICS Min Typ Max Unit/Comments Start Voltage 5 VDC Input Models 12 VDC Input Models 24 VDC Input Models 4.75 10.8 21.6 5.25 13.2 26.4 VDC VDC VDC OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Balance (Duals) Line Regulation Min Typ Max Unit/Comments ±5.0 % Output voltage at nominal line & FL ±3.0 % Equal Output Loads ±0.5 % Output voltage measured from min. input line to maximum ±0.5 % Output voltage measured from FL to 10% load 50 mV p-p, Nom.Line @FL, 20MHz B.W., using 1 μf bypass capacitor Continuous, Automatic Recovery ±0.02 % per degree C GENERAL CHARACTERISTICS Switching Frequency Isolation Voltage Isolation Resistance Isolation Capacitance Input Filter MTBF (MIL-HBK-217F) Min Typ Max Unit/Comments kHz 40 VDC, 1 minute 3000 Mohm, 500VDC 1000 20 pF, 100kHz, 1Volt Pi Filter Million Hours, 0.8 +25oC, Ground Benign Load Regulation Ripple/Noise Short Circuit Protection Temperature Coefficient >> 1 www.make-ps.com ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Storage Temp. Range Relative Humidity Cooling Min -25 -40 Typ Max +71 +125 95 Unit/Comments C; Ambient o C % Humidity; noncondensing Free-Air Convection o E-mail:info@make-ps.com PHYSICAL CHARACTERISTICS Case Size Case Material Flammability Weight Unit/Comments 1.25 X 0.8 X 0.4 inches (31.8 X 20.3 X 10.2 mm) Non-conductive Black Plastic UL94V-0 14 Grams OUTLINE DRAWING 1.25 [31.8] .40 [10.2] SIDE VIEW .020 (.50) TYP. PIN DIA. .15 [3.8] .100 [2.54] TYP. 12 10 11 12 .08 [2.0] .10 [2.5] .80 [20.3] 24 23 15 14 13 BOTTOM VIEW .800 [20.32] .600 [15.24] PIN OUT CHART Pins 1, 2 23, 24 15 13 10, 11 12, 14 Single + Vin - Vin NC + Vout NC - Vout NC -Dual +Vin - Vin +Vout - Vout ± COMMON NC NC Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 X.XXX= ±0.010 X.XX = ±0.25 Pin : ±0.002 ±0.05 All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. NC = No Connection >> 2 www.make-ps.com HOW TO ORDER E-mail:info@make-ps.com HOW TO ORDER 2 XX S XX HFR - Y Wattage Output Voltage Output Configuration (S=Single, D=Dual) ROHS Compliant Series Nominal Input Range MODEL SELECTION CHART Model 205S5HFR 212S5HFR 215S5HFR 205S12HFR 212S12HFR 205S24HFR 212S24HFR 212D5HFR 215D5HFR 212D12HFR 212D24HFR Nominal Input Voltage (VDC) 5 5 5 12 12 24 24 5 5 12 24 Input Current No Load (mA) 120 120 120 50 50 25 25 120 120 50 25 Input Current Full Load (mA) 666 660 665 277 275 138 137 664 660 276 138 Output Voltage (VDC) 5 12 15 5 12 5 12 ±12 ±15 ±12 ±12 Full Load Output Current (mA) 400 165 133 400 165 400 165 ±83 ±66 ±83 ±83 Efficiency @ FL (%) 60 63 63 60 63 60 63 62 62 62 62 >> 3 www.make-ps.com DERATING CURVES E-mail:info@make-ps.com MODEL 200HFR - SINGLE OUTPUT Pout % 100 90 80 70 60 50 40 30 20 10 0 -40 100LFM 200LFM 400LFM Natural Convection 50 60 70 80 90 100 110 TEMPERATURE ° C MODEL 200HFR - DUAL OUTPUT Pout % 100 90 80 70 60 50 40 30 20 10 0 -40 100LFM 200LFM Natural Convection 400LFM 50 60 70 80 90 100 110 TEMPERATURE ° C >> 4