MTSM0302AZ-HR-A

3Northway Lane North Latham,New York 12110. Tollfree:1.800.984.5337 Phone:1.518.956.2980 Fax:1.518.785.4725 Http://www.marktechopto.com SPECIFICATION PART NO. : MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP MTSM0302AZ-HR-A 1.8mm AXIAL LED LAMP Package Dimensions 0.15 4° 1.925 1.4 R0 .8 3 0.875 3.05 4.3 5.8 2.5 0.5 1.8 0.4 2.0 1.5 2.8 K A Notes: 1. All dimensions are in mm. 2. Tolerance is ±0.25mm unless otherwise noted. Description LED Chip Part No. Material AlGaInP/GaAs Emitting Color Deep Red Lens Color MTSM0302AZ-HR-A Water Clear VER.: 01 Date: 2007/10/04 Page: 1/6 MTSM0302AZ-HR-A Absolute Maximum Ratings at Ta=25℃ Parameter Power Dissipation Reverse Voltage D.C. Forward Current Peak Current(1/10Duty Cycle,0.1ms Pulse Width.) Operating Temperature Range Storage Temperature Range Soldering Temperature 1.8mm AXIAL LED LAMP Symbol PD VR If If(Peak) Topr. Tstg. Tsld. Rating 72 5 30 100 -40 to +100 -40 to +100 Unit mW V mA mA ℃ ℃ Reflow Soldering: 260℃ for 10 sec. Electrical and Optical Characteristics: Parameter Luminous Intensity Forward Voltage Peak Wavelength Dominant Wavelength Reverse Current Viewing Angle Spectrum Line Halfwidth Symbol IV Vf λp λd Ir 2θ1/2 Condition If=20mA If=20mA If=20mA If=20mA Vr=5V If=20mA If=20mA Min. 622 Typ. 1050 1.9 650 639 Max. Unit mcd 2.4 V nm nm 100 36 20 µA deg nm ∆λ Notes: 1.The datas tested by IS tester. 2. Customer’s special requirements are also welcome. VER.: 01 Date: 2007/10/04 Page: 2/6 MTSM0302AZ-HR-A Typical Electrical/Optical Characteristic Curves 1.8mm AXIAL LED LAMP (25℃ Ambient Temperature Unless Otherwise Noted) Forward Current IF(mA) 40 30 20 10 Relative Luminous Intensity(mcd0 1.8 2.0 2.2 2.4 2.6 50 1500 1200 900 600 300 0 1.6 0.0 10.0 20.0 30.0 Applied Voltage (V) Forward Current (mA) Forward Current VS. Applied Voltage Forward Current VS. Luminous Intensity 50 40 30 20 10 1.0 0.9 0.8 0° 10° 20° 30° Forward Current IF(mA) 40° 50° 60° 70° 80° 90° 0.5 0.3 0.1 0.2 0.4 0.6 0 20 40 60 80 Ambient Temperature Ta (℃) 100 0.7 Ambient Temperature VS. Forward Current Radiation Diagram VER.: 01 Date: 2007/10/04 Page: 3/6 MTSM0302AZ-HR-A PRECAUTION IN USE Storage 1.8mm AXIAL LED LAMP Recommended storage environment Temperature: 5oC ~ 30oC (41oF ~ 86oF) Humidity: 60% RH Max. Use within 7 days after opening of sealed vapor/ESD barrier bags. If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. Fold the opened bag firmly and keep in dry environment. Soldering Reflow Soldering Lead Solder 120~150℃ Pre-heat Pre-heat time 120sec. Max. 240℃ Max. Peak temperature Soldering time 10sec. Max. Condition refer to Temperatureprofile 1 *After reflow soldering rapid cooling should be avoided. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. ＜1 : Lead Solder＞ 2.5~5°C/sec. Pre-heating 120~150°C 120sec. Max. 2.5~5°C/sec. 240°C Max. 10sec. Max. Lead – free Solder 180~200℃ 120sec. Max. 260℃ Max. 10sec. Max. refer to Temperatureprofile 2 ＜2 : Lead-free Solder＞ 1~5°C/sec. Pre-heating 180~200°C 120sec. Max. 1~5°C/sec. 260°C Max. 10sec. Max. 60sec. Max. 60sec. Max. VER.: 01 Date: 2007/10/04 Page: 4/6 MTSM0302AZ-HR-A Dimensions for Tape 2.0 4.0 1.55 1.8mm AXIAL LED LAMP 0.3 1.75 5° MAX 11 ° MAX 12.0 0.15 5.5 1.65 4.0 3.05 Dimensions for Reel 178.0±1 13.2±0.5 16.2±0.5 Notes: 1.All dimensions are in mm, tolerance is±2.0mm unless otherwise noted. 2.Specifications are subject to change without notice. 60.0±0.5 57 VER.: 01 Date: 2007/10/04 Page: 5/6 2.16 MTSM0302AZ-HR-A Packing REEL QUANTITY: 1,500 PCS Marktech Optoelectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: 1.8mm AXIAL LED LAMP Marktech Optoelectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: 溼氣敏感材料 MOISTURE SENSITIVE DEVICES 1. 在5°C~30°C密封貯藏， 1年有效。 Shelf life in sealed bag : 12 months at 5°C~30°C . 2. 開封後需在168小時內使用。 Devices have to be mounted within 168 hours after this bag is opened . 230± 1.0 BAG QUANTITY: 1,500 PCS Marktech Optoelectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: 270±1.0 INSIDE BOX QUANTITY: 4 BAGS TOTAL: 6,000 PCS 27 5± 2 23 5± 2 Q'TY : PCS LOT NO :XXXXXXXXX DATE : BIN CODE: Notes: 1. All dimensions are in mm, tolerance is±2.0mm unless otherwise noted. 2. Specifications are subject to change without notice. VER.: 01 Date: 2007/10/04 Page: 6/6 75±2 Marktech Optoelectronics. PART NO :MTXXXX-XX 178±1 RE SEN 料 1. |b5°C SITIVE ~30° C±K Shelf ?E?J DEV life at 5°C~ in seale AA!A2|~|3RA ICES d bag 30°C 2. ?}?E : 24 mont !C ?a?Y . hs D evice |b72 ?pRE ?o I￥ ‥ I!C 72 hour s have to be MOISTU 溼氣敏 Marktech Optoel ectronics. PART NO :MTXXXX-XX Q'TY : PCS LOT NO :XXXXXXXX X DATE : BIN CODE: s after moun this bag ted withi n is open ed . 感材