TLYK31TPF

TLYK31TP(F) TOSHIBA LED Lamp InGaAℓP Yellow Light Emission TLYK31TP(F) Panel Circuit Indicator • • • • • • • • • Lead(Pb)-free products (lead: Sn-Ag-Cu) 5 mm package InGaAℓP technology Transparent lens Low drive current, high intensity yellow light emission Recommended forward current: IF = 10~30 mA (DC) All plastic molded lens, provides an excellent on−off contrast ratio. Fast response time, capable of pulse operation. Applications: outdoor message signboards,Traffic signals, Safety equipment, HMSL,etc Stopper lead type is also available. TLYK31T(F) 6.75±0.2 Unit in mm Maximum Ratings (Ta = 25°C) Characteristic Forward current (DC) Reverse voltage Power dissipation Operating temperature range Storage temperature range Symbol IF VR PD Topr Tstg Rating 50 4 130 −40~100 −40~120 Unit mA V mW °C °C Cathode index 1. ANODE 2. CATHODE JEDEC EIAJ TOSHIBA Weight: 0.28 g ― ― ― For part availability and ordering information please call Toll Free: 800.984.5337 Website: www.marktechopto.com | Email: info@marktechopto.com HOL-0133 1 2007-01-24 TLYK31TP(F) Electrical And Optical Characteristics (Ta = 25°C) Characteristic Forward voltage Reverse current Luminous intensity Peak emission wavelength Spectral line half width Dominant wavelength Symbol VF IR IV λP ∆λ λd Test Condition IF = 20 mA VR = 4 V IF = 20 mA IF = 20 mA IF = 20 mA IF = 20 mA (Note) (Note) Min 1.9 ⎯ 1530 ⎯ ⎯ 581 Typ. 2.4 ⎯ 4000 (594) 13 590 Max 2.6 50 ⎯ ⎯ ⎯ 595 Unit V µA mcd nm nm nm (Note): Lamps are classified into the following ranks according to Iv and λd, and packed in boxes by each rank. Iv-rank ⇒ Ｔ: 1530−4140mcd, Ｕ: 2720−7360mcd, Ｖ: 4760mcd− λd-rank ⇒ 1: 581−588nm, 2: 585−592nm, 3: 589−595nm Precaution • • • Please be careful of the followings Soldering temperature: 260°C max Soldering time: 3 s max (Soldering portion of lead: up to 1.6 mm from the body of the device) If the lead is formed, the lead should be formed up to1.6 mm from the body of the device without forming stress to the resin. Soldering should be performed after lead forming. This visible LED lamp also emits some IR light. If a photodetector is located near the LED lamp, please ensure that it will not be affected by this IR light. HOL-0133 2 2007-01-24 TLYK31TP(F) IF – V F 100 50 10000 Ta = 25 °C Ta = 25°C IV – IF 30 Luminous intensity IV (mcd) 1.8 2.0 2.2 2.4 2.6 2.8 (mA) Forward current IF 1000 10 5 3 100 1 1.6 30 1 3 5 10 30 50 100 Forward voltage VF (V) Forward current IF (mA) IV – Tc 10 5 1.0 Relative Luminous Intensity Wavelength IF = 20 mA Ta = 25°C 0.8 Relative luminous intensity IV 3 Relative luminous intensity 0.6 1 0.5 0.3 0.4 0.2 0.1 −20 0 20 40 60 80 0 540 560 580 600 620 640 660 Case temperature Tc (°C) Wavelength λ (nm) Radiation Pattern 80 IF – Ta Ta = 25 °C Allowable forward current IF (mA) 60 20° 30° 40° 50° 60° 70° 80° 90° 10° 0° 10° 20° 30° 40° 50° 60° 70° 80° 40 20 0 0.2 0.4 0.6 0.8 90° 1.0 0 0 20 40 60 80 100 120 Ambient temperature Ta (°C) HOL-0133 3 2007-01-24 TLYK31TP(F) RESTRICTIONS ON PRODUCT USE 000707EAC • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. • Gallium arsenide (GaAs) is a substance used in the products described in this document. GaAs dust and fumes are toxic. Do not break, cut or pulverize the product, or use chemicals to dissolve them. When disposing of the products, follow the appropriate regulations. Do not dispose of the products with other industrial waste or with domestic garbage. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. HOL-0133 4 2007-01-24