676-501-23

PROFESSIONAL LED INDICATORS Ø 8.1mm Mounting FEATURES Black anodised aluminium housing 676 SERIES PACK QUANTITY = 10 PIECES Sealed to IP67 Smoked lens for good on/off contrast ratio Internally potted for use in high vibration applications Internal reverse protection diode fitted as standard in all voltage models. Wide viewing angle SPECIFICATION Ordering Information & Typical T echnical Characteristics (T a = 25°C) Mean Time Between Failure = 100,000 Hours. PART NUMBER COLOUR Luminous intensity figures refer to the unmodified discrete LED. VOLTAGE CURRENT LUMINOUS WAVE OPERATING STORAGE LENS DC (Vdc) Vopr DC (mA) lopr INTENSITY lv@20mA (mcd) LENGTH λp (nm) TEMP T opr TEMP T stg HIGH INTENSITY 676-501-21 676-521-21 676-532-21 676-930-21 676-997-21 676-501-23 676-521-23 676-532-23 676-930-23 676-997-23 UNITS Red Yellow Green Blue Cool White Red Yellow Green Blue Cool White Smoked Smoked Smoked Smoked Smoked Smoked Smoked Smoked Smoked Smoked 12 12 12 12 12 24-28 24-28 24-28 24-28 24-28 Vdc 20 20 20 20 20 20 20 20 20 20 mA 11000 16000 23000 7000 14000 11000 16000 23000 7000 14000 mcd 643 591 527 470 see below 643 591 527 470 see below nm -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ -40 ~ +95^ °C -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 -40 ~ +100 °C Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Other voltages AC/DC available. Please contact our Technical Sales. ^ = Products must be derated according to the derating information. Each derating graph refers to specific LEDs. x y 997F-C 0.245 0.229 *Typical emission colour cool white 0.361 0.356 0.264 Intensities (lv) and colour shades of white (x,y co-ordinates) may vary between LEDs within a batch. 0.385 0.351 0.220 How to Order: website: www.marl.co.uk • email: sales@marl.co.uk • • T elephone +44 (0)1229 582430 • Fax: +44 (0)1229 585155 relating to either products or service. for products or service. The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation Marl International reserve the right to alter without notice the specification or any conditions of supply © MARL INTERNATIONAL LTD 2007 : DS 050/06 Issue 2 SAMPLES AVAILABLE Page 1 of 3 676 Series MOUNTING HOLE Dimensions in mm (Typical) Not to scale Anode termination indicated by red sleeve Mounting hole to be clean and burr free. MATERIALS Body Nut Panel Seal T ermination T ags Lens Encapsulation Lock Washer Black anodised aluminium Bright Nickel Plated Brass Viton Silver Flash Coated Brass Polycarbonate PC5430 resin Spring Steel PUSH-ON CONNECTORS 925-000-00 is brass tin plated. Dimensions in mm (Typical) Not to scale For use with 676 series lamps. TECHNICAL CHARACTERISTICS SERIES MAXIMUM DISSIPATION 676 UNITS 700 mW POWER MAXIMUM VOLTAGE 3* / 1000• Vdc • = Voltage Version REVERSE PANEL NUT MINIMUM MIN/MAX. THICKNESS 1.5-13.0 mm PANEL CUTOUT TORQUE 0.6 Nm MOUNTING CENTRES x,y = 14.5 mm MOUNTING 8.1 mm * = Current Version OPTIONAL FLYING LEAD TERMINATIONS ORDER SUFFIX 15 15 19 19 CODE SUPPLY WIRE WIRE NO/DIAMETER CONDUCTORS OF DIAMETER INSULATION OVER COMMENTS VOLTAGE COLOUR LENGTH DC Products AC Products DC Products AC Products Red-anode / Black-cathode Brown-live / Blue-neutral Red-anode / Black-cathode Brown-live / Blue-neutral 150mm 150mm 1000mm 1000mm Customised available 19/0.15mm 1.2mm lengths website: www.marl.co.uk • email: sales@marl.co.uk • • T elephone +44 (0)1229 582430 • Fax: +44 (0)1229 585155 relating to either products or service. for products or service. The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation Marl International reserve the right to alter without notice the specification or any conditions of supply Approved Manufacturer BS EN ISO 9001:2000 © MARL INTERNATIONAL LTD 2007 : DS 050/06 Issue 2 Page 2 of 3 DERATING INFORMATION 501 & 521 532, 930 & 997 website: www.marl.co.uk • email: sales@marl.co.uk • • T elephone +44 (0)1229 582430 • Fax: +44 (0)1229 585155 relating to either products or service. for products or service. The information contained in this datasheet does not constitute part of any order or contract and should not be regarded as a representation Marl International reserve the right to alter without notice the specification or any conditions of supply Approved Manufacturer BS EN ISO 9001:2000 © MARL INTERNATIONAL LTD 2007 : DS 050/06 Issue 2 Page 3 of 3