MAS9186AUA1

DA9186.001 29 January, 2004 MAS9186 This is preliminary information on a new product under development. Micro Analog Systems Oy reserves the right to make any changes without notice. 8 X 8-bit D to A Converter • 3-pin Serial Data Interface • Low Voltage Output Buffer DESCRIPTION MAS9186 is 8-channel 8-bit DAC, designed primarily for trimmer replacement. Device is controlled by a simple 3-line input. The output buffers operate in the entire voltage range from ground to the positive power supply rail. DAC is selected with three first bits in serial input data (SDI-pin) and the DAC output value is set according to the last 8 bits in serial input data. FEATURES • • • • • Eight 8-bit DACs on a single monolithic chip Voltage level output TSSOP 16 package Single +2.7V supply Power-on reset APPLICATIONS • • • High resolution monitors Automatic gain control Trimmer replacement BLOCK DIAGRAM SDI CLK 11-bit Shift Register MAS9186A2 8-bit data 8-BIT DAC 8-BIT DAC 8-BIT DAC 8-BIT DAC 8-BIT DAC O8 O7 O6 O5 O4 O3 XCS Address Decoder 8-BIT DAC 8-BIT DAC 8-BIT DAC O2 O1 VDD VREFH VREFL (XRESET in MAS9186A1) GND 1 (9) DA9186.001 29 January, 2004 PIN CONFIGURATION VREFH O1 O2 O3 O4 O5 O6 XSHDN 1 2 3 4 5 6 7 8 16 VDD 15 XRESET 14 08 13 O7 12 SDI 11 CLK 10 GND 9 VREFH 1 O1 2 16 VDD 15 O8 14 O7 O2 3 O3 4 O4 5 O5 6 O6 7 XSHDN 8 MAS9186A1 YYWW MAS9186A2 YYWW 13 SDI 12 CLK 11 VREFL 10 GND 9 XCS XCS Top view YYWW = year, week PIN DESCRIPTION Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MAS9186 A1 VREFH O1 O2 O3 O4 O5 O6 XSHDN XCS GND CLK SDI O7 O8 XRESET VDD MAS9186 A2 VREFH O1 O2 O3 O4 O5 O6 XSHDN XCS GND VREFL CLK SDI O7 O8 VDD Function DAC output reference high voltage DAC 1, address 0x0 DAC 2, address 0x1 DAC 3, address 0x2 DAC 4, address 0x3 DAC 5, address 0x4 DAC 6, address 0x5 Device analog part power-down signal (active low) Device enable signal (rising edge loads data to DAC) Device ground-pin Data clock / DAC output low reference voltage Serial input data / Data clock DAC 7, address 0x6 / Serial input data DAC 8, address 0x7 / DAC 7, address 0x6 Device Digital part reset – middle code preset pin/DAC 8, address 0xB Device power supply pin MAS9186 has two bonding options available: • • MAS9186A1, where VREFL pin is bonded to GND pin and XRESET pin can be used MAS9186A2, where XRESET pin is bonded to VDD pin and VREFL pin can be used 2 (9) DA9186.001 29 January, 2004 ABSOLUTE MAXIMUM RATINGS Parameter Power Supply (VDD to GND) Input Voltage Range (any other pin) Continuous Power Dissipation Storage Temperature Range -65 Symbol VDD Conditions Min -0.3 -0.3 Max +6.0 VDD + 0.3 1000 +150 Unit V V mW °C RECOMMENDED OPERATION CONDITIONS Parameter Supply Voltage Range Operating Temperature Range Symbol VDD Temp Conditions Min 2.7 -40 Typ 3.6 Max 5.5 +85 Unit V °C ELECTRICAL CHARACTERISTICS (VDD = 3.0 V ± 10% or 5.0 V ± 10%, VREFH = VDD, VREFL = 0V, -40°C ≤ TA ≤ +85°C unless otherwise noted) DC Parameters ◆ Digital Inputs Parameter DAC Resolution DAC Differential Nonlinearity Error DAC Integral Nonlinearity Error DAC Full-scale Error DAC Zero Code Error DAC Output Resistance ◆ Reference Input Parameter REFH Voltage Range Symbol N DNL INL GFSE BZSE ROUT Conditions Min -1 -1 -1 -1 Typ 8 Max +1 +1 +1 +1 Unit Bits LSB LSB LSB LSB Ω 30 60 Symbol VREFH VREFL RREFH RREFL Conditions VREFH > VREFL VREFH > VREFL Min 0 0 5 Typ Max VDD VDD Unit REFL Voltage Range (MAS9186A2 only) REFH Input Resistance REFL Input Resistance 10 10 kΩ kΩ 3 (9) DA9186.001 29 January, 2004 ◆ Digital Input Parameter Digital Logic High Digital Logic Low Digital Input Current ◆ Power Supplies Parameter Power Supply Range Supply Current Supply Current Shutdown Current Symbol VDD IDD IDD ISHDN VDD = 3.60V VDD = 5.50V 0.5 Conditions Min 2.7 3 Typ Max 5.5 6 20 5 Unit V mA mA uA Symbol VIH VIL IIL Conditions Min 0.7*VDD 0.3*VDD ±1 uA Typ Max Unit AC Parameters ◆ AC Characteristics Dynamic Performance Parameter Power Supply Sensitivity (100Hz) Vout Settling time (±1/2 LSB error band) Crosstalk between adjacent outputs Switching Characteristics (Minimum values at +25 C, VDD = 3.60 V) o Symbol PSRR TS CT Conditions Min Typ 54 6 63 Max Unit dB µs dB Parameter Input Clock High Pulse Width Input Clock Low Pulse Width Data Setup Time Data Hold Time XCS Fall to First Clock Pulse Fall XCS High Pulse Width RESET Pulse Width CLK Rise to XCS Rise Hold Time XCS Rise to CLOCK Rise Setup Symbol TCH TCL TDS TDH TCLCL TCSW TRS TCSH TCS1 Conditions Min Typ 16 7 -5 5 16 22 28 22 -5 Max Unit ns ns ns ns ns ns ns ns ns 4 (9) DA9186.001 29 January, 2004 OPERATING MODES DAC maximum output voltage is set using VREFH and VREFL pins (= 255/256 * (VREFH-VREFL)+VREFL) (note: VREFL=GND in case of MAS9186A1). XRESET pin is used for middle code preset: DAC registers are reset and middle code will appear at the DAC output. Serial input data is written to SDI while XCS is low. Data is read at CLK rising edge to on-chip shift register. Rising XCS-pin stops data reading and 11 CLK-cycles are used as the input data (3 address bits and 8 data bits). The last 11 bits before rising XCS are used as input data. ◆ Timing diagram SDI A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 CLK XCS VOUT APPLICATION AND TEST CIRCUIT INFORMATION +3.0v DAC Register Load 16 VDD 1 VREFH MAS9186A2 8 XSHDN Controller Clock Data In Latch 12 13 9 CLK SDI O8 XCS O7 O6 O5 O4 O3 15 14 7 6 5 4 3 2 100 nF GND 10 O2 O1 VREFL 11 5 (9) DA9186.001 29 January, 2004 PACKAGE (TSSOP16) OUTLINES C D Seating Plane B A F G H E O Pin 1 Detail A B B L I I1 K P Section B-B J1 J M N Detail A Dimension Min Max A 6.40 BSC B 4.30 4.50 C 5.00 BSC D 0.05 0.15 E 1.10 F 0.19 0.30 G 0.65 BSC H 0.18 0.28 I 0.09 0.20 I1 0.09 0.16 J 0.19 0.30 J1 0.19 0.25 K 0° 8° L 0.24 0.26 M 0.50 0.75 (The length of a terminal for soldering to a substrate) N 1.00 REF O 12 ° P 12 ° Dimensions do not include mold flash, protrusions, or gate burrs. All dimensions are in accordance with JEDEC standard MO-153. Unit mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm 6 (9) DA9186.001 29 January, 2004 SOLDERING INFORMATION Resistance to Soldering Heat Maximum Temperature Maximum Number of Reflow Cycles Reflow profile Seating Plane Co-planarity Lead Finish According to RSH test IEC 68-2-58/20 2*220°C 240°C 2 Thermal profile parameters stated in JESD22-A113 should not be exceeded. http://www.jedec.org max 0.08 mm Solder plate 7.62 - 25.4 µm, material Sn 85% Pb 15% EMBOSSED TAPE SPECIFICATIONS Tape Feed Direction P0 D0 P2 A E1 F1 W D1 A P A0 Tape Feed Direction T Section A - A B0 S1 K0 Dimension A0 B0 D0 D1 E1 F1 K0 P P0 P2 S1 T W Min 6.50 5.20 1.50 +0.10 / -0.00 1.50 1.65 7.20 1.20 11.90 4.0 1.95 0.6 0.25 11.70 2.05 0.35 12.30 1.85 7.30 1.40 12.10 Pin 1 Designator Max 6.70 5.40 Unit mm mm mm mm mm mm mm mm mm mm mm mm mm 7 (9) DA9186.001 29 January, 2004 REEL SPECIFICATIONS W2 A D B Tape Slot for Tape Start C N W1 2000 Components on Each Reel Reel Material: Conductive, Plastic Antistatic or Static Dissipative Carrier Tape Material: Conductive Cover Tape Material: Static Dissipative Carrier Tape Cover Tape End Start Trailer Dimension A B C D N W1 (measured at hub) W2 (measured at hub) Trailer Leader Components Min 1.5 12.80 20.2 50 12.4 Max 330 13.50 14.4 18.4 160 390, of which minimum 160mm of empty carrier tape sealed with cover tape 1500 Leader Unit mm mm mm mm mm mm mm mm mm Weight g 8 (9) DA9186.001 29 January, 2004 ORDERING INFORMATION Product Code MAS9186AUA1 MAS9186AUA2 Product 8 x 8-bit D to A Converter 8 x 8-bit D to A Converter Package TSSOP-16 TSSOP-16 Comments 0 V Reference Level Scalable Reference Level LOCAL DISTRIBUTOR MICRO ANALOG SYSTEMS OY CONTACTS Micro Analog Systems Oy Kamreerintie 2, P.O. Box 51 FIN-02771 Espoo, FINLAND Tel. +358 9 80 521 Fax +358 9 805 3213 http://www.mas-oy.com NOTICE Micro Analog Systems Oy reserves the right to make changes to the products contained in this data sheet in order to improve the design or performance and to supply the best possible products. Micro Analog Systems Oy assumes no responsibility for the use of any circuits shown in this data sheet, conveys no license under any patent or other rights unless otherwise specified in this data sheet, and makes no claim that the circuits are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Micro Analog Systems Oy makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification. 9 (9)