MAX1419ETN

19-3011; Rev 0; 10/03 KIT ATION EVALU E AILABL AV 15-Bit, 65Msps ADC with -79.3dBFS Noise Floor for Baseband Applications General Description Features o 65Msps Minimum Sampling Rate o -79.3dBFS Noise Floor o Excellent Dynamic Performance 76.2dB SNR at fIN=15MHz and AIN = -1dBFS 93.1dBc/95.5dBc Single-Tone SFDR1/SFDR2 at fIN = 15MHz and AIN = -1dBFS -91dBc Multitone SFDR at fIN1 = 10MHz and fIN2 = 15MHz o Less than 0.25ps Sampling Jitter o Fully Differential Analog Input Voltage Range of 2.56VP-P o CMOS-Compatible Two’s-Complement Data Output o Separate Data Valid Clock and Overrange Outputs o Flexible-Input Clock Buffer o EV Kit Available for the MAX1419 (Order MAX1427EVKIT) MAX1419 The MAX1419 is a 5V, high-speed, high-performance analog-to-digital converter (ADC) featuring a fully differential wideband track-and-hold (T/H) and a 15-bit converter core. The MAX1419 is optimized for multichannel, multimode receivers, which require the ADC to meet very stringent dynamic performance requirements. With a noise floor of -79.3dBFS, the MAX1427 allows for the design of receivers with superior sensitivity. The MAX1419 achieves two-tone, spurious-free dynamic range (SFDR) of -91dBc for input tones of 10MHz and 15MHz. Its excellent signal-to-noise ratio (SNR) of 76.2dB and single-tone SFDR performance (SFDR1/SFDR2) of 93.1dBc/95.5dBc at fIN = 15MHz and a sampling rate of 65Msps make this part ideal for high-performance digital receivers. The MAX1419 operates from an analog 5V and a digital 3V supply, features a 2.56VP-P full-scale input range, and allows for a sampling speed of up to 65Msps. The input T/H operates with a -1dB full-power bandwidth of 200MHz. The MAX1419 features parallel, CMOS-compatible outputs in two’s-complement format. To enable the interface with a wide range of logic devices, this ADC provides a separate output driver power-supply range of 2.3V to 3.5V. The MAX1419 is manufactured in an 8mm x 8mm, 56-pin QFN package with exposed paddle (EP) for low thermal resistance, and is specified for the extended industrial (-40°C to +85°C) temperature range. Note that IF parts MAX1418, MAX1428, and MAX1430 (see the Pin-Compatible Higher/Lower Speed Versions Selection table) are recommended for applications that require high dynamic performance for input frequencies greater than fCLK/3. The MAX1419 is optimized for input frequencies of less than fCLK/3. Ordering Information PART MAX1419ETN *EP TEMP RANGE -40°C to +85°C PIN-PACKAGE 56 QFN-EP* = Exposed paddle. Applications Cellular Base-Station Transceiver Systems (BTS) Wireless Local Loop (WLL) Single- and Multicarrier Receivers Multistandard Receivers E911 Location Receivers Power Amplifier Linearity Correction Antenna Array Processing Pin-Compatible Higher/Lower Speed Versions Selection PART MAX1418 MAX1419 MAX1427 MAX1428* MAX1429* MAX1430* SPEED GRADE (Msps) 65 65 80 80 100 100 TARGET APPLICATION IF Baseband Baseband IF Baseband IF Pin Configuration appears at end of data sheet. *Future product—contact factory for availability. ________________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 15-Bit, 65Msps ADC with -79.3dBFS Noise Floor for Baseband Applications MAX1419 ABSOLUTE MAXIMUM RATINGS AVCC, DVCC, DRVCC to GND.................................. -0.3V to +6V INP, INN, CLKP, CLKN, CM to GND........-0.3V to (AVCC + 0.3V) D0–D14, DAV, DOR to GND..................-0.3V to (DRVCC + 0.3V) Continuous Power Dissipation (TA = +70°C) 56-Pin QFN (derate 47.6mW/°C above +70°C) ......3809.5mW Operating Temperature Range ...........................-40°C to +85°C Thermal Resistance θJA ...................................................21°C/W Junction Temperature ......................................................+150°C Storage Temperature Range .............................-60°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (AVCC = 5V, DVCC = DRVCC = 2.5V, GND = 0, INP and INN driven differentially with -1dBFS, CLKP and CLKN driven differentially with a 2VP-P sinusoidal input signal, CL = 5pF at digital outputs, fCLK = 65MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise noted. ≥+25°C guaranteed by production test,