MXB7843_05

19-2435; Rev 1; 9/05 2.375V to 5.25V, 4-Wire Touch-Screen Controller General Description The MXB7843 is an industry-standard 4-wire touchscreen controller. It contains a 12-bit sampling analogto-digital converter (ADC) with a synchronous serial interface and low on-resistance switches for driving resistive touch screens. The MXB7843 uses an external reference. The MXB7843 can make absolute or ratiometric measurements. The MXB7843 has two auxiliary ADC inputs. All analog inputs are fully ESD protected, eliminating the need for external TransZorb™ devices. The MXB7843 is guaranteed to operate with a single 2.375V to 5.25V supply voltage. In shutdown mode, the typical power consumption is reduced to under 0.5µW, while the typical power consumption at 125ksps throughput and a 2.7V supply is 650µW. Low-power operation makes the MXB7843 ideal for battery-operated systems, such as personal digital assistants with resistive touch screens and other portable equipment. The MXB7843 is available in 16-pin QSOP and TSSOP packages, and is guaranteed over the -40°C to +85°C temperature range. Features ♦ ESD-Protected ADC Inputs ±15kV IEC 61000-4-2 Air-Gap Discharge ±8kV IEC 61000-4-2 Contact Discharge ♦ Pin Compatible with MXB7846 ♦ +2.375V to +5.25V Single Supply ♦ 4-Wire Touch-Screen Interface ♦ Ratiometric Conversion ♦ SPI™/QSPI™, 3-Wire Serial Interface ♦ Programmable 8-/12-Bit Resolution ♦ Two Auxiliary Analog Inputs ♦ Automatic Shutdown Between Conversions ♦ Low Power 270µA at 125ksps 115µA at 50ksps 25µA at 10ksps 5µA at 1ksps 2µA Shutdown Current MXB7843 Applications Personal Digital Assistants Portable Instruments Point-of-Sales Terminals Pagers Touch-Screen Monitors Cellular Phones Ordering Information PART MXB7843EEE MXB7843EUE TEMP RANGE -40°C to +85°C -40°C to +85°C PIN-PACKAGE 16 QSOP 16 TSSOP Typical Application Circuit appears at end of data sheet. TransZorb is a trademark of Vishay Intertechnology, Inc. SPI/QSPI are trademarks of Motorola, Inc. TOP VIEW VDD 1 X+ 2 Y+ 3 X- 4 Y- 5 GND 6 IN3 7 IN4 8 16 DCLK 15 CS 14 DIN Pin Configuration MXB7843 13 BUSY 12 DOUT 11 PENIRQ 10 VDD 9 REF QSOP/TSSOP ________________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 ABSOLUTE MAXIMUM RATINGS VDD, DIN, CS, DCLK to GND ...................................-0.3V to +6V Digital Outputs to GND...............................-0.3V to (VDD + 0.3V) VREF, X+, X-, Y+, Y-, IN3, IN4 to GND........-0.3V to (VDD + 0.3V) Maximum Current into Any Pin .........................................±50mA Maximum ESD per IEC-61000-4-2 (per MIL STD-883 HBM) X+, X-, Y+, Y-, IN3, IN4 ...........................................15kV (4kV) All Other Pins ..........................................................2kV (500V) Continuous Power Dissipation (TA = +70°C) 16-Pin QSOP (derate 8.30mW/°C above +70°C).........667mW 16-Pin TSSOP (derate 5.70mW/°C above +70°C) .......456mW Operating Temperature Range ...........................-40°C to +85°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = 2.7V to 3.6V, VREF = 2.5V, fDCLK = 2MHz (50% duty cycle), fSAMPLE = 125kHz, 12-bit mode, 0.1µF capacitor at REF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER DC ACCURACY (Note 1) Resolution No Missing Codes Relative Accuracy Differential Nonlinearity Offset Error Gain Error Noise CONVERSION RATE Conversion Time Track/Hold Acquisition Time Throughput Rate Multiplexer Settling Time Aperture Delay Aperture Jitter Channel-to-Channel Isolation Serial Clock Frequency Duty Cycle ANALOG INPUT (X+, X-, Y+, Y-, IN3, IN4) Input Voltage Range Input Capacitance Input Leakage Current SWITCH DRIVERS On-Resistance (Note 5) Y+, X+ Y-, X7 9 Ω On/off-leakage, VIN = 0 to VDD 0 25 ±0.1 ±1 VREF V pF µA fDCLK VIN = 2.5VP-P at 50kHz 0.1 40 tCONV tACQ fSAMPLE 12 clock cycles (Note 4) 3 clock cycles 16 clock conversion 500 30 100 100 2.0 60 1.5 125 6 µs µs kHz ns ns ps dB MHz % (Note 3) 70 INL DNL (Note 2) 11 12 ±1 ±1 ±6 ±4 ±2 12 Bits Bits LSB LSB LSB LSB µVRMS SYMBOL CONDITIONS MIN TYP MAX UNITS 2 _______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller ELECTRICAL CHARACTERISTICS (continued) (VDD = 2.7V to 3.6V, VREF = 2.5V, fDCLK = 2MHz (50% duty cycle), fSAMPLE = 125kHz, 12-bit mode, 0.1µF capacitor at REF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER Reference Input Voltage Range Input Resistance fSAMPLE = 125kHz Input Current DIGITAL INPUTS (DCLK, CS, DIN) Input High Voltage Input Low Voltage Input Hysteresis Input Leakage Current Input Capacitance DIGITAL OUTPUT (DOUT, BUSY) Output Voltage Low Output Voltage High PENIRQ Output Low Voltage Three-State Leakage Current Three-State Output Capacitance POWER REQUIREMENTS Supply Voltage Supply Current Shutdown Supply Current Power-Supply Rejection Ratio VDD fSAMPLE = 125ksps IDD ISHDN PSRR fSAMPLE = 12.5ksps fSAMPLE = 0 DCLK = CS = VDD VDD = 2.7V to 3.6V full scale 70 2.375 270 220 150 3 µA dB 5.250 650 µA V VIH VIL VHYST IIN CIN VOL VOH VOL IL COUT ISINK = 250µA ISOURCE = 250µA 50kΩ pullup to VDD CS = VDD CS = VDD 1 15 VDD 0.5 0.8 ±10 15 0.4 100 ±1 ✕ MXB7843 SYMBOL (Note 6) CONDITIONS MIN 1 TYP MAX VDD UNITS V GΩ REFERENCE (Reference applied to REF) 5 13 2.5 ±3 VDD 0.7 0.8 40 µA fSAMPLE = 12.5kHz fDCLK = 0 V V mV µA pF V V V µA pF _______________________________________________________________________________________ 3 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 TIMING CHARACTERISTICS (Figure 1) (VDD = 2.7V to 3.6V, VREF = 2.5V, fDCLK = 2MHz (50% duty cycle), fSAMPLE = 125kHz, 12-bit mode, 0.1µF capacitor at REF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER Acquisition Time DCLK Clock Period DCLK Pulse Width High DCLK Pulse Width Low DIN-to-DCLK Setup Time DIN-to-DCLK Hold Time CS Fall-to-DCLK Rise Setup Time CS Rise-to-DCLK Rise Ignore DCLK Falling-to-DOUT Valid CS Rise-to-DOUT Disable CS Fall-to-DOUT Enable DCLK Falling-to-BUSY Rising CS Falling-to-BUSY Enable CS Rise-to-BUSY Disable SYMBOL tACQ tCP tCH tCL tDS tDH tCSS tCSH tDO tTR tDV tBD tBDV tBTR CLOAD = 50pF CLOAD = 50pF CLOAD = 50pF CONDITIONS MIN 1.5 500 200 200 100 0 100 0 200 200 200 200 200 200 TYP MAX UNITS µs ns ns ns ns ns ns ns ns ns ns ns ns ns TIMING CHARACTERISTICS (Figure 1) Note 1: Tested at VDD = +2.7V. Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has been calibrated. Note 3: Offset nulled. Note 4: Conversion time is defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle. Note 5: Resistance measured from the source to drain of the switch. Note 6: ADC performance is limited by the conversion noise floor, typically 300µVP-P. An external reference below 2.5V can compromise the ADC performance. 4 _______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Typical Operating Characteristics (VDD = 2.7V, VREF = 2.5V, fDCLK = 2MHz, fSAMPLE = 125kHz, CLOAD = 50pF, 0.1µF capacitor at REF, TA = +25°C, unless otherwise noted.) INTEGRAL NONLINEARITY vs. DIGITAL OUTPUT CODE MXB7843 toc01 DIFFERENTIAL NONLINEARITY vs. DIGITAL OUTPUT CODE MXB7843 toc02 CHANGE IN OFFSET ERROR vs. SUPPLY VOLTAGE 1.5 OFFSET ERROR (LSB) 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 MXB7843 toc04 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 0 INL (LSB) 1.0 0.8 0.6 0.4 DNL (LSB) 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 2.0 500 1000 1500 2000 2500 3000 3500 4000 OUTPUT CODE 0 500 1000 1500 2000 2500 3000 3500 4000 OUTPUT CODE 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) CHANGE IN OFFSET ERROR vs. TEMPERATURE MXB7843 toc05 CHANGE IN GAIN ERROR vs. SUPPLY VOLTAGE MXB7843 toc07 CHANGE IN GAIN ERROR vs. TEMPERATURE MXB7843 toc08 1.0 OFFSET ERROR FROM +25°C (LSB) 3 2 GAIN ERROR (LSB) 1 0 -1 -2 1.0 GAIN ERROR FROM +25°C (LSB) 0.5 0 -0.5 -1.0 -1.5 -2.0 0.5 0 -0.5 -1.0 -40 -25 -10 5 20 35 50 65 80 TEMPERATURE (°C) -3 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) -40 -25 -10 5 20 35 50 65 80 TEMPERATURE (°C) SWITCH ON-RESISTANCE vs. SUPPLY VOLTAGE (X+, Y+ : + VDD TO PIN; X-, Y- : TO GND) MXB7843 toc03 SWITCH ON-RESISTANCE vs. TEMPERATURE (X+, Y+ : + VDD TO PIN; X-, Y- : PIN TO GND) 11 10 9 8 7 6 5 4 3 2 1 0 XX+ YY+ MXB7843 toc06 14 12 X10 RON (Ω) 12 Y6 4 2 0 2.5 3.0 3.5 X+ Y+ 4.0 4.5 5.0 5.5 RON (Ω) 8 -40 -25 -10 5 20 35 50 65 80 SUPPLY VOLTAGE (V) TEMPERATURE (°C) _______________________________________________________________________________________ 5 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Typical Operating Characteristics (continued) (VDD = 2.7V, VREF = 2.5V, fDCLK = 2MHz, fSAMPLE = 125kHz, CLOAD = 50pF, 0.1µF capacitor at REF, TA = +25°C, unless otherwise noted.) REFERENCE CURRENT vs. SUPPLY VOLTAGE MXB7843 toc12 REFERENCE CURRENT vs. TEMPERATURE MXB7843 toc13 REFERENCE CURRENT vs. SAMPLE RATE 9 REFERENCE CURRENT (µA) 8 7 6 5 4 3 2 1 0 MXB7843 toc14 8.3 8.2 REFERENCE CURRENT (µA) 8.1 8.0 7.9 7.8 7.7 2.5 CL = 0.1µF fSAMPLE = 125kHz 8.3 8.2 REFERENCE CURRENT (µA) 8.1 8.0 7.9 7.8 7.7 VDD = 2.7V CL = 0.1µF fSAMPLE = 125kHz -40 -25 -10 5 20 35 50 65 80 10 3.0 3.5 4.0 4.5 5.0 5.5 0 25 50 75 100 125 SUPPLY VOLTAGE (V) TEMPERATURE (°C) SAMPLE RATE (kHz) SUPPLY CURRENT vs. SUPPLY VOLTAGE MXB7843 toc18 SUPPLY CURRENT vs. TEMPERATURE MXB7843 toc19 SUPPLY CURRENT vs. SAMPLE RATE VDD = 2.7V VREF = 2.5V MXB7843 toc20 250 fSAMPLE = 12.5kHz SUPPLY CURRENT (µA) 225 290 285 SUPPLY CURRENT (µA) 280 275 270 265 260 255 fSAMPLE = 125kHz VDD = 2.7V 250 225 SUPPLY CURRENT (µA) 200 175 150 125 100 200 175 150 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) 250 -40 -25 -10 5 20 35 50 65 80 TEMPERATURE (°C) 0 25 50 75 100 125 SAMPLE RATE (kHz) SHUTDOWN CURRENT vs. SUPPLY VOLTAGE MXB7843 toc21 SHUTDOWN CURRENT vs. TEMPERATURE MXB7843 toc22 MAXIMUM SAMPLE RATE vs. SUPPLY VOLTAGE MXB7843 toc23 300 DLCK = CS = VDD SHUTDOWN CURRENT (nA) 250 120 DCLK = CS = VDD 110 SHUTDOWN CURRENT (nA) 100 90 80 70 60 50 1000 SAMPLE RATE (kHz) -40 -25 -10 5 20 35 50 65 80 100 200 150 10 100 50 2.7 3.2 3.7 4.2 4.7 5.2 SUPPLY VOLTAGE (V) 1 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 TEMPERATURE (°C) SUPPLY VOLTAGE (V) 6 _______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller Pin Description PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NAME VDD X+ Y+ XYGND IN3 IN4 REF VDD PENIRQ DOUT BUSY DIN CS DCLK Positive Supply Voltage. Connect to pin 10. X+ Position Input, ADC Input Channel 1 Y+ Position Input, ADC Input Channel 2 X- Position Input Y- Position Input Ground Auxiliary Input to ADC; ADC Input Channel 3 Auxiliary Input to ADC; ADC Input Channel 4 Voltage Reference Input. Reference voltage for analog-to-digital conversion. Apply a reference voltage between 1V and VDD. Bypass REF to GND with a 0.1µF capacitor. Positive Supply Voltage, +2.375V to +5.25V. Bypass with a 1µF capacitor. Connect to pin 1. Pen Interrupt Output. Open anode output. 10kΩ to 100kΩ pullup resistor required to VDD. Serial Data Output. Data changes state on the falling edge of DCLK. High impedance when CS is HIGH. Busy Output. BUSY pulses high for one clock period before the MSB decision. High impedance when CS is HIGH. Serial Data Input. Data clocked in on the rising edge of DCLK. Active-Low Chip Select. Data is only clocked into DIN when CS is low. When CS is high, DOUT and BUSY are high impedance. Serial Clock Input. Clocks data in and out of the serial interface and sets the conversion speed (duty cycle must be 40% to 60%). FUNCTION MXB7843 _______________________________________________________________________________________ 7 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Detailed Description The MXB7843 uses a successive-approximation conversion technique to convert analog signals to a 12-bit digital output. An SPI/QSPI/MICROWIRE™-compatible serial interface provides an easy communication to a microprocessor (µP). It features a 4-wire touch-screen interface and two auxiliary ADC channels (Functional Diagram). The time required for the T/H to acquire an input signal is a function of how quickly its input capacitance is charged. If the input signal’s source impedance is high, the acquisition time lengthens, and more time must be allowed between conversions. The acquisition time (tACQ) is the maximum time the device takes to acquire the input signal to 12-bit accuracy. Calculate tACQ with the following equation: t ACQ = 8.4 × (RS + RIN ) × 25pF where RIN = 2kΩ and RS is the source impedance of the input signal. Source impedances below 1k Ω do not significantly affect the ADC’s performance. Accommodate higher source impedances by either slowing down DCLK or by placing a 1µF capacitor between the analog input and GND. Analog Inputs Figure 2 shows a block diagram of the analog input section that includes the input multiplexer of the MXB7843, the differential signal inputs of the ADC, and the differential reference inputs of the ADC. The input multiplexer switches between X+, X-, Y+, Y-, IN3, and IN4. In single-ended mode, conversions are performed using REF as the reference. In differential mode, ratiometric conversions are performed with REF+ connected to X+ or Y+, and REF- connected to X- or Y-. Configure the reference and switching matrix according to Tables 1 and 2. During the acquisition interval, the selected channel charges the sampling capacitance. The acquisition interval starts on the fifth falling clock edge and ends on the eighth falling clock edge. Input Bandwidth and Anti-Aliasing The ADCs input tracking circuitry has a 25MHz smallsignal bandwidth, so it is possible to digitize highspeed transient events. To avoid high-frequency signals being aliased into the frequency band of interest, anti-alias filtering is recommended. CS tCH tCL DCLK tCSS tCP tCSH tDS tDO tDH DIN tTR tDV DOUT tBDV tBTR BUSY tBD Figure 1. Detailed Serial Interface Timing MICROWIRE is a trademark of National Semiconductor Corp. 8 _______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Functional Diagram VDD X+ X- DOUT Y+ Y6-TO-1 MUX 12-BIT ADC SERIAL DATA INTERFACE DCLK IN3 IN4 REF DIN CS BUSY PENIRQ Table 1. Input Configuration, Single-Ended Reference Mode (SER/DFR HIGH) A2 0 0 0 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 MEASUREMENT Reserved Y-Position IN3 Reserved Reserved X-Position IN4 Reserved ADC INPUT CONNECTION Reserved X+ IN3 Reserved Reserved Y+ IN4 Reserved DRIVERS ON — Y+, Y— — — X-, X+ — — Table 2. Input Configuration, Differential Reference Mode (SER/DFR LOW) A2 0 1 A1 0 0 A0 1 1 ADC +REF CONNECTION TO Y+ X+ ADC -REF CONNECTION TO YXADC INPUT CONNECTION TO X+ Y+ MEASUREMENT PERFORMED Y position X position DRIVER ON Y+, YX+, X- _______________________________________________________________________________________ 9 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Analog Input Protection Internal protection diodes, which clamp the analog input to VDD and GND, allow the analog input pins to swing from GND - 0.3V to VDD + 0.3V without damage. Analog inputs must not exceed V DD by more than 50mV or be lower than GND by more than 50mV for accurate conversions. If an off-channel analog input voltage exceeds the supplies, limit the input current to 50mA. The analog input pins are ESD protected to ±8kV using the Contact-Discharge method and ±15kV using the Air-Gap method specified in IEC 61000-4-2. Differential Measurement Mode Figure 4 shows the switching matrix configuration for Y-coordinate measurement. The REF+ and REF- inputs are connected directly to the Y+ and Y- pins, respectively. Differential mode uses the voltage at the Y+ pin as the REF+ voltage and voltage at the Y- pin as REFvoltage. This conversion is ratiometric and independent of the voltage drop across the drivers and variation in the touch-screen resistance. In differential mode, the touch screen remains biased during the acquisition and conversion process. This results in additional supply current and power dissipation during conversion when compared to the absolute measurement mode. PEN Interrupt Request (PENIRQ) Figure 5 shows the block diagram for the PENIRQ function. When used, PENIRQ requires a 10kΩ to 100kΩ pullup to +VDD. If enabled, PENIRQ goes low whenever the touch screen is touched. The PENIRQ output can be used to initiate an interrupt to the microprocessor, which can write a control word to the MXB7843 to start a conversion. Figure 6 shows the timing diagram for the PENIRQ pin function. The diagram shows that once the screen is touched while CS is high, the PENIRQ output goes low after a time period indicated by tTOUCH. The tTOUCH value changes for different touch-screen parasitic capacitance and resistance. The microprocessor receives this interrupt and pulls CS low to initiate a conversion. At this instant, the P ENIRQ pin should be masked, as transitions can occur due to a selected input channel or the conversion mode. The PENIRQ pin functionality becomes valid when either the last data bit is clocked out, or CS is pulled high. Touch-Screen Conversion The MXB7843 provides two conversion methods—differential and single ended. The SER/DFR bit in the control word selects either mode. A logic 1 selects a single-ended conversion, while a logic 0 selects a differential conversion. Differential vs. Single Ended Changes in operating conditions can degrade the accuracy and repeatability of touch-screen measurements. Therefore, the conversion results representing X and Y coordinates may be incorrect. For example, in singleended measurement mode, variation in the touchscreen driver voltage drops results in incorrect input reading. Differential mode minimizes these errors. Single-Ended Mode Figure 3 shows the switching matrix configuration for Y-coordinate measurement in single-ended mode. The MXB7843 measures the position of the pointing device by connecting X+ to IN+ of the ADC, enabling Y+ and Y- drivers, and digitizing the voltage on X+. The ADC performs a conversion with REF+ = REF and REF- = GND. In single-ended measurement mode, the bias to the touch screen can be turned off after the acquisition to save power. The on-resistance of the X and Y drivers results in a gain error in single-ended measurement mode. Touchscreen resistance ranges from 200Ω to 900Ω (depending on the manufacturer), whereas the on-resistance of the X and Y drivers is 8Ω (typ). Limit the touch-screen current to less than 50mA by using a touch screen with a resistance higher than 100Ω. The resistive divider created by the touch screen and the on-resistance of the X and Y drivers result in both an offset and a gain shift. Also, the on-resistance of the X and Y drivers does not track the resistance of the touch screen over temperature and supply. This results in further measurement errors. External Reference During conversion, an external reference at REF must deliver up to 40µA DC load current. If the reference has a higher output impedance or is noisy, bypass it close to the REF pin with a 0.1µF and a 4.7µF capacitor. 10 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 PENIRQ VDD REF A2–A0 (SHOWN 001B) SER/DFR (SHOWN HIGH) X+ X- Y+ Y- +IN +REF CONVERTER -IN -REF IN3 IN4 GND Figure 2. Equivalent Input Circuit VDD VDD Y+ REF Y+ X+ +IN -IN REF+ 12-BIT ADC REF- X+ +IN -IN REF+ 12-BIT ADC REF- Y- Y- GND GND Figure 3. Single-Ended Y-Coordinate Measurement Figure 4. Ratiometric Y-Coordinate Measurement 11 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 VDD OPEN CIRCUIT Y+ 100kΩ PENIRQ TOUCH SCREEN X+ YON PENIRQ ENABLE Figure 5. PENIRQ Functional Block Diagram SCREEN TOUCHED HERE PENIRQ CS DCLK 1 2 3 4 5 6 7 8 1 2 3 12 13 14 15 16 DIN S A2 A1 A0 M S/D PD1 PD0 INTERRUPT PROCESSOR NO RESPONSE TO TOUCHMASK PENIRQ tTOUCH PENIRQ ENABLED Figure 6. PENIRQ Timing Diagram 12 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller Digital Interface Initialization After Power-Up and Starting a Conversion The digital interface consists of three inputs, DIN, DCLK, CS, and one output, DOUT. A logic-high on CS disables the MXB7843 digital interface and places DOUT in a high-impedance state. Pulling C S low enables the MXB7843 digital interface. Start a conversion by clocking a control byte into DIN (Table 3) with C S low. Each rising edge on DCLK clocks a bit from DIN into the MXB7843’s internal shift register. After C S falls, the first arriving logic 1 bit defines the control byte’s START bit. Until the START bit arrives, any number of logic 0 bits can be clocked into DIN with no effect. The MXB7843 is compatible with SPI/QSPI/MICROWIRE devices. For SPI, select the correct clock polarity and sampling edge in the SPI control registers of the microcontroller: set CPOL = 0 and CPHA = 0. MICROWIRE, SPI, and QSPI all transmit a byte and receive a byte at the same time. The simplest software interface requires only three 8-bit transfers to perform a conversion (one 8bit transfer to configure the ADC, and two more 8-bit transfers to read the conversion result) (Figure 7). Simple Software Interface Make sure the CPU’s serial interface runs in master mode so the CPU generates the serial clock. Choose a clock frequency from 500kHz to 2MHz: 1) Set up the control byte and call it TB. TB should be in the format: 1XXXXXXX binary, where X denotes the particular channel, selected conversion mode, and power mode (Tables 3, 4). 2) Use a general-purpose I/O line on the CPU to pull CS low. 3) Transmit TB and simultaneously receive a byte; call it RB1. 4) Transmit a byte of all zeros ($00 hex) and simultaneously receive byte RB2. 5) Transmit a byte of all zeros ($00 hex) and simultaneously receive byte RB3. 6) Pull CS high. Figure 7 shows the timing for this sequence. Bytes RB2 and RB3 contain the result of the conversion, padded by four trailing zeros. The total conversion time is a function of the serial-clock frequency and the amount of idle timing between 8-bit transfers. Digital Output The MXB7843 outputs data in straight binary format (Figure 10). Data is clocked out on the falling edge of the DCLK, MSB first. MXB7843 Serial Clock The external clock not only shifts data in and out, but it also drives the analog-to-digital conversion steps. BUSY pulses high for one clock period after the last bit of the control byte. Successive-approximation bit decisions are made and appear at DOUT on each of the next 12 DCLK falling edges. BUSY and DOUT go into a high-impedance state when CS goes high. The conversion must complete in 500µs or less; if not, droop on the sample-and-hold capacitors can degrade conversion results. Data Framing The falling edge of CS does not start a conversion. The first logic high clocked into DIN is interpreted as a start bit and defines the first bit of the control byte. A conversion starts on DCLK’s falling edge, after the eighth bit of the control byte is clocked into DIN. The first logic 1 clocked into DIN after bit 6 of a conversion in progress is clocked onto the DOUT pin and is treated as a START bit (Figure 8). Once a start bit has been recognized, the current conversion must be completed. The fastest the MXB7843 can run with CS held continuously low is 15 clock conversions. Figure 8 shows the serial-interface timing necessary to perform a conversion every 15 DCLK cycles. If CS is connected low and DCLK is continuous, guarantee a start bit by first clocking in 16 zeros. Most microcontrollers (µCs) require that data transfers occur in multiples of eight DCLK cycles; 16 clocks per conversion is typically the fastest that a µC can drive the MXB7843. Figure 9 shows the serial-interface timing necessary to perform a conversion every 16 DCLK cycles. 8-Bit Conversion The MXB7843 provides an 8-bit conversion mode selected by setting the MODE bit in the control byte high. In the 8-bit mode, conversions complete four clock cycles earlier than in the 12-bit output mode, resulting in 25% faster throughput. This can be used in conjunction with serial interfaces that provide 12-bit transfers, or two conversions could be accomplished with three 8-bit transfers. Not only does this shorten each conversion by 4 bits, but each conversion can also ______________________________________________________________________________________ 13 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 CS TB tACQ DCLK 1 4 8 9 RB2 12 16 RB3 20 24 DIN S A2 A1 SER/ A0 MODE DFR PD1 PD0 (START) BUSY IDLE ACQUIRE CONVERSION IDLE RB1 DOUT A/D STATE DRIVERS1 AND 2 (SER/DFR HIGH) IDLE ACQUIRE 11 (MSB) 10 9 8 7 6 5 4 3 2 1 0 (LSB) CONVERSION IDLE OFF ON OFF DRIVERS1 AND 2 (SER/DFR LOW) OFF ON OFF Figure 7. Conversion Timing, 24-Clock per Conversion, 8-Bit Bus Interface CS 1 DCLK 8 15 1 8 15 1 DIN S CONTROL BYTE 0 S CONTROL BYTE 1 S CONTROL BYTE 2 DOUT B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 CONVERSION RESULT 0 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 CONVERSION RESULT 1 BUSY Figure 8. 15-Clock/Conversion Timing occur at a faster clock rate since settling to better than 8 bits is all that is required. The clock rate can be as much as 25% faster. The faster clock rate and fewer clock cycles combine to increase the conversion rate. Applications Information Basic Operation of the MXB7843 The 4-wire touch-screen controller works by creating a voltage gradient across the vertical or horizontal resistive network connected to the MXB7843, as shown in the Typical Application Circuit. The touch screen is biased through internal MOSFET switches that connect each resistive layer to VDD and ground on an alternate basis. For example, to measure the Y position when a Data Format The MXB7843 output data is in straight binary format as shown in Figure 10. This figure shows the ideal output code for the given input voltage and does not include the effects of offset, gain, or noise. 14 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 CS 1 DCLK 8 16 1 8 16 ... ... ... B11 B10 B9 B8 B7 B6 CONVERSION RESULT 1 DIN S CONTROL BYTE 0 S CONTROL BYTE 1 DOUT B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 CONVERSION RESULT 0 ... ... BUSY Figure 9. 16-Clock/Conversion Timing Table 3. Control Byte Format BIT 7 START BIT 6 A2 BIT 5 A1 BIT 4 A0 BIT 3 MODE BIT 2 SER/DFR BIT 1 PD1 BIT 0 PD0 BIT 7 6 5 4 3 2 1 0 NAME START A2 A1 A0 MODE SER/DFR PD1 PD0 Address (Tables 1 and 2) Start bit DESCRIPTION Conversion resolution. 1 = 8 bits, 0 = 12 bits. Conversion mode. 1 = single ended, 0 = differential. Power-down mode (Table 4) Table 4. Power Mode Selection SUPPLY CURRENT (typ) (µA) PD1 0 0 1 1 PD0 0 1 0 1 PENIRQ Enabled Disabled Disabled Disabled STATUS ADC is ON during conversion, OFF between conversion ADC is always ON Reserved ADC is always ON DURING CONVERSION 200 200 — 200 AFTER CONVERSION 1 200 — 200 ______________________________________________________________________________________ 15 2.375V to 5.25V, 4-Wire Touch-Screen Controller pointing device presses on the touch screen, the Y+ and Y- drivers are turned on, connecting one side of the vertical resistive layer to VDD and the other side to ground. In this case, the horizontal resistive layer functions as a sense line. One side of this resistive layer gets connected to the X+ input, while the other side is left open or floating. The point where the touch screen is pressed brings the two resistive layers in contact and forms a voltage-divider at that point. The data converter senses the voltage at the point of contact through the X+ input and digitizes it. The horizontal layer resistance does not introduce any error in the conversion because no DC current is drawn. The conversion process of the analog input voltage to digital output is controlled through the serial interface between the A/D converter and the µP. The processor controls the MXB7843 configuration through a control byte (Tables 3 and 4). Once the processor instructs the MXB7843 to initiate a conversion, the MXB7843 biases the touch screen through the internal switches at the beginning of the acquisition period. The voltage transient at the touch screen needs to settle down to a stable voltage before the acquisition period is over. After the acquisition period is over, the A/D converter goes into a conversion period with all internal switches turned off if the device is in single-ended mode. If the device is in differential mode, the internal switches remain on from the start of the acquisition period to the end of the conversion period. MXB7843 OUTPUT CODE FULL-SCALE TRANSITION 11…111 11…110 11…101 FS = (VREF+ - VREF-) 1LSB = (VREF+ - VREF-) 4096 00…011 00…010 00…001 00…000 0 1 2 3 FS-3/2LSB INPUT VOLTAGE (LSB) = [(V+IN) - (V-IN)] FS Figure 10. Ideal Input Voltages and Output Codes PD1 = 0 and PD0 = 0. When exiting software shutdown, the MXB7843 is ready to perform a conversion in 10µs. PD1 = 1, PD0 = 1 In this mode, the MXB7843 is always powered. The device remains fully powered after the current conversion completes. PD1 = 0, PD0 = 0 In this mode, the MXB7843 powers down after the current conversion completes or on the next rising edge of CS, whichever occurs first. The next control byte received on DIN powers up the MXB7843. At the start of a new conversion, it instantly powers up. When each conversion is finished, the part enters power-down mode, unless otherwise indicated. The first conversion after the ADC returns to full power is valid for differential conversions and single-ended measurement conversions. When operating at full speed and 16 clocks per conversion, the difference in power consumption between PD1 = 0, PD0 = 1, and PD1 = 0, PD0 = 0 is negligible. Also, in the case where the conversion rate is decreased by slowing the frequency of the DCLK input, the power consumption between these two modes is not very different. When the DCLK frequency is kept at Power-On Reset When power is first applied, internal power-on circuitry resets the MXB7843. Allow 10µs for the first conversion after the power supplies stabilize. If CS is low, the first logic 1 on DIN is interpreted as a start bit. Until a conversion takes place, DOUT shifts out zeros. Power Modes Save power by placing the converter in one of two lowcurrent operating modes or in full power-down between conversions. Select the power-down mode through PD1 and PD0 of the control byte (Tables 3 and 4). The software power-down modes take effect after the conversion is completed. The serial interface remains active while waiting for a new control byte to start a conversion and switches to full-power mode. After completing its conversion, the MXB7843 enters the programmed power mode until a new control byte is received. The power-up wait before conversion period is dependent on the power-down state. When exiting software low-power modes, conversion can start immediately when running at decreased clock rates. Upon poweron reset, the MXB7843 is in power-down mode with 16 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller the maximum rate during a conversion, conversions are done less often. There is a significant difference in power consumption between these two modes. PD1 = 0, PD0 = 1 In this mode, the MXB7843 is powered down. This mode becomes active after the current conversion completes or on the next rising edge of CS, whichever occurs first. The next command byte received on the DIN returns the MXB7843 to full power. The first conversion after the ADC returns to full power is valid. PD1 = 1, PD0 = 0 This mode is reserved. Hardware Power-Down CS also places the MXB7843 into power-down. When CS goes HIGH, the MXB7843 immediately powers down and aborts the current conversion. 8-bit data stream contains the first 8-bits of the current conversion, starting with the MSB. The second 8-bit data stream contains the remaining 4 result bits followed by 4 trailing zeros. DOUT then goes high impedance when CS goes high. QSPI/SPI Interface The MXB7843 can be used with the QSPI/SPI interface using the circuit in Figure 12 with CPOL = 0 and CPHA = 0. This interface can be programmed to do a conversion on any analog input of the MXB7843. TMS320LC3x Interface Figure 13 shows an example circuit to interface the MXB7843 to the TMS320. The timing diagram for this interface circuit is shown in Figure 14. Use the following steps to initiate a conversion in the MXB7843 and to read the results: 1) The TMS320 should be configured with CLKX (transmit clock) as an active-high output clock and CLKR (TMS320 receive clock) as an active-high input clock. CLKX and CLKR on the TMS320 are connected to the MXB7843 DCLK input. 2) The MXB7843’s C S pin is driven low by the TMS320’s XF I/O port to enable data to be clocked into the MXB7843’s DIN pin. 3) An 8-bit word (1XXXXXXX) should be written to the MXB7843 to initiate a conversion and place the device into normal operating mode. See Table 3 to select the proper XXXXXXX bit values for your specific application. 4) The MXB7843’s BUSY output is monitored through the TMS320’s FSR input. A falling edge on the BUSY output indicates that the conversion is in progress and data is ready to be received from the devices. 5) The TMS320 reads in 1 data bit on each of the next 16 rising edges of DCLK. These bits represent the 12-bit conversion result followed by 4 trailing bits. 6) Pull CS high to disable the MXB7843 until the next conversion is initiated. MXB7843 Touch-Screen Settling There are two key touch-screen characteristics that can degrade accuracy. First, the parasitic capacitance between the top and bottom layers of the touch screen can result in electrical ringing. Second, vibration of the top layer of the touch screen can cause mechanical contact bouncing. External filter capacitors may be required across the touch screen to filter noise induced by the LCD panel or backlight circuitry, etc. These capacitors lengthen the settling time required when the panel is touched and can result in a gain error, as the input signal may not settle to its final steady-state value before the ADC samples the inputs. Two methods to minimize or eliminate this issue are described below. One option is to lengthen the acquisition time by stopping or slowing down DCLK, allowing for the required touchscreen settling time. This method solves the settling time problem for both single-ended and differential modes. The second option is to operate the MXB7843 in the differential mode only for the touch screen, and perform additional conversions with the same address until the input signal settles. The MXB7843 can then be placed in the power-down state on the last measurement. Layout, Grounding, and Bypassing For best performance, use printed circuit (PC) boards with good layouts; wire-wrap boards are not recommended. Board layout should ensure that digital and analog signal lines are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the ADC package. Establish a single-point analog ground (star ground point) at GND. Connect all analog grounds to the star 17 Connection to Standard Interface MICROWIRE Interface When using the MICROWIRE- (Figure 11) or SPI-compatible interface (Figure 12), set the CPOL = CPHA = 0. Two consecutive 8-bit readings are necessary to obtain the entire 12-bit result from the ADC. DOUT data transitions occur on the serial clock’s falling edge and are clocked into the µP on the DCLK’s rising edge. The first ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 I/O SCK MISO MICROWIRE CS DCLK DOUT MXB7843 DIN BUSY QSPI/SPI I/O SCK MISO CS DCLK DOUT MXB7843 MOSI MASKABLE INTERRUPT DIN BUSY MOSI MASKABLE INTERRUPT Figure 11. MICROWIRE Interface Figure 12. QSPI/SPI Interface ground. Connect the digital system ground to the star ground at this point only. For lowest noise operation, minimize the length of the ground return to the star ground’s power supply. Power-supply decoupling is also crucial for optimal device performance. Analog supplies can be decoupled by placing a 10µF tantalum capacitor in parallel with a 0.1µF capacitor bypassed to GND. To maximize performance, place these capacitors as close as possible to the supply pin of the device. Minimize capacitor lead length for best supply-noise rejection. If the supply is very noisy, a 10Ω resistor can be connected in series as a lowpass filter. While using the MXB7843, the interconnection between the converter and the touch screen should be as short as possible. Since touch screens have low resistance, longer or loose connections may introduce error. Noise can also be a major source of error in touch-screen applications (e.g., applications that require a backlight LCD panel). EMI noise coupled through the LCD panel to the touch screen may cause flickering of the converted data. Utilizing a touch screen with a bottom-side metal layer connected to ground decouples the noise to ground. In addition, the filter capacitors from Y+, Y-, X+, and X- inputs to ground also help further reduce the noise. Caution should be observed for settling time of the touch screen, especially operating in the singleended measurement mode and at high data rates. XF CLKX CLKR TMS320LC3x DX DR FSR CS SCLK MXB7843 DIN DOUT BUSY Figure 13. TMS320 Serial Interface static linearity parameters for the MXB7843 are measured using the end-point method. Differential Nonlinearity Differential nonlinearity (DNL) is the difference between an actual step width and the ideal value of 1LSB. A DNL error specification of less than 1LSB guarantees no missing codes and a monotonic transfer function. Aperture Jitter Aperture jitter (tAJ) is the sample-to-sample variation in the time between the samples. Aperture Delay Aperture delay (tAD) is the time defined between the falling edge of the sampling clock and the instant when an actual sample is taken. Definitions Integral Nonlinearity Integral nonlinearity (INL) is the deviation of the values on an actual transfer function from a straight line. This straight line can be either a best-straight-line fit or a line drawn between the endpoints of the transfer function, once offset and gain errors have been nullified. The Chip Information TRANSISTOR COUNT: 12,000 PROCESS: 0.6µm BiCMOS 18 ______________________________________________________________________________________ 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 CS DCLK DIN START A2 A1 A0 MODE SER/DEF PD1 PD0 BUSY HIGH IMPEDANCE DOUT MSB B10 B1 B0 HIGH IMPEDANCE Figure 14. MXB7843-to-TMS320 Serial Interface Timing Diagram Typical Application Circuit 2.375V TO 5.5V 1µF TO 10µF OPTIONAL 0.1µF 1 2 VDD X+ DCLK 16 CS 15 DIN 14 SERIAL/CONVERSION CLOCK CHIP SELECT SERIAL DATA IN CONVERTER STATUS SERIAL DATA OUT PEN INTERRUPT 50kΩ 0.1µF 3 Y+ 4 XTOUCH SCREEN 5 Y6 GND MXB7843 BUSY 13 DOUT 12 PENIRQ 11 VDD 10 REF 9 7 IN3 8 IN4 ______________________________________________________________________________________ 19 2.375V to 5.25V, 4-Wire Touch-Screen Controller MXB7843 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) PACKAGE OUTLINE, QSOP .150", .025" LEAD PITCH 21-0055 E 1 1 20 ______________________________________________________________________________________ QSOP.EPS 2.375V to 5.25V, 4-Wire Touch-Screen Controller Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) TSSOP4.40mm.EPS MXB7843 PACKAGE OUTLINE, TSSOP 4.40mm BODY 21-0066 G 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 21 © 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.