8408RPFB

Quad 8-Bit Multiplying CMOS D/A Converter with Memory 8408 Logic Diagram Memory FEATURES: • RAD-PAK® patented shielding against natural • space radiation • Total dose hardness: - equal to 100 krad (Si), depending upon orbit and space mission • Package: - 28 pin RAD-PAK® Flat Pack • Single Supply Ooperation (+5V) • Four 8 Bit DACs in one 28 Pin Package • D/As Matched to within 1% • TTL/CMOS Compatable • Four-Quadrant Multiplication own reference input, feedback resistor, and onboard data latches that feature read/write capability. The readback function serves as memory for those systems requiring self-diagnostics. A common 8-bit TTL/CMOS compatible input port is used to load data into any of the four DAC data-latches. Control lines DS1, DS2 and A/B determine which DAC will accept data. Data loading is similar to that of a RAMs write cycle. Data can be read back onto the same bus with control line R/W. The 8408 is a bus compatible with most 8-bit microprocessors, including the 6800, 8080, 8085, and Z80. The 8408 operates on a single +5 volt supply and dissipates less than 20 mW. The 8408 is manufactured using highly stable, thin-film resistors on an advanced oxide-isolated, silicon-gate, CMOS process. The improved latch-up resistant design eliminates the need for external protective Schottky diodes. Maxwell Technologies' patented RAD-PAK® packaging technology incorporates radiation shielding in the microcircuit package. It eliminates the need for box shielding while providing the required radiation shielding for a lifetime in orbit or space mission. In a GEO orbit, RAD-PAK provides greater than 100 krad (Si) radiation dose tolerance. This product is available with screening up to Class S. DESCRIPTION: Maxwell Technologies’ 8408 is a monolithic quad 8-bit multiplying digital-to-analog CMOS converter. Each DAC has its 08.20.02 REV 1 All data sheets are subject to change without notice 1 (858) 503-3300- Fax: (858) 503-3301- www.maxwell.com ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory TABLE 1. 8408 PINOUT DESCRIPTION PIN 1 2 3 4 5 6 7 8 9 10 - 15 16 17 18 19 - 20 21 22 23 24 25 26 27 28 SYMBOL VDD VREFA RFBA IOUT 1A IOUT 2A/IOUT 2B IOUT 1B RFBB VREFB DB0 (LSB) DB 1 - 6 DB 7 (MSB) A/B R/W DS1 - 2 VREFD RFBD IOUT 1D IOUT 2C/IOUT 2D IOUT 1C RFBC VREFC DGND DESCRIPTION Supply Voltage REF Voltage (A) REF Feedback (A) Current Output (1A) Current Output (2A/2B) Current Output (1B) REF Feedback (B) REF Voltage (B) Data Bit 0, least significant bit Data bits 1-6 Data Bit 7, most significant bit A/B Read/Write Data Strobes REF Voltage (D) REF Feedback (D) Current Output (1D) Current Output (2C/2D) Current Output (1C) REF Feedback (C) REF Voltage (C) Digital Ground 8408 Memory TABLE 2. 8408 ABSOLUTE MAXIMUM RATINGS PARAMETER VDD to IOUT 2A, IOUT 2B, IOUT 2C, IOUT 2D VDD to DGND IOUT 1A, IOUT 1B, IOUT 1C, IOUT 1D to DGND RRFA, RRFB, VRFC, RRFD to IOUT IOUT 2A, IOUT 2B, IOUT 2C, IOUT 2D to DGND DB0 through DB7 to DGND Control Logic Input Voltage to DGND VREFA, VREFB, VREFC, VREFD to IOUT 2A, IOUT 2B, IOUT 2C, IOUT 2D 08.20.02 REV 1 SYMBOL --------- MIN 0 0 -0.3 --0.3 -0.3 -0.3 -- MAX 7 7 VDD + 0.3 ±25 VDD + 0.3 VDD + 0.3 VDD + 0.3 ±25 UNIT V V V V V V V V All data sheets are subject to change without notice 2 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory PARAMETER Power Dissipation Operating Temperature Storage Temperature Range 8408 SYMBOL PD TA TS MIN --55 -65 MAX 20 125 150 UNIT mW °C °C TABLE 2. 8408 ABSOLUTE MAXIMUM RATINGS TABLE 3. DELTA LIMITS PARAMETER IDD VARIATION ±10% of value specified in Table 4 TABLE 4. 8408 SPECIFICATIONS (VDD = +5 V; VREF = ±10V; VOUTA, B, C, D = 0V, TA = -55 TO 125 °C UNLESS OTHERWISE NOTED) PARAMETER STATIC ACCURACY Resolution Non-linearity1, 2 Differential Nonlinearity Gain Error Gain Tempco3, 4 Power Supply Rejection IOUT 1A, B,C, D Leakage Current5 REFERENCE INPUT Input Voltage Range Input Resistance DIGITAL INPUTS Digital Input High Voltage Digital Input Low Voltage Digital Input Current6 Digital Input Capacitance4 DATA BUS OUTPUTS Digital Output Low Digital Output High VOL VOH 16 mA Sink 400 µA Source 08.20.02 REV 1 SYMBOL TEST CONDITION SUBGROUPS MIN TYP MAX UNIT Memory N INL DNL GFSE TCGFS PSR ILKG (Using Internal RFB) 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 +25°C -55 to 125°C 1 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 8 --------6 2.4 -----4 ----±2 ----10 --±0.01 ----- -±1/2 ±1 ±1 ±40 0.001 ±30 ±200 ±20 14 -0.8 ±1.0 ±10.0 8 0.4 -- Bits LSB LSB LSB ppm/°C %FSR/ % nA ∆VDD = ±10% +25°C -55 to 125°C -RIN VIH VIL IIN CIN V KΩ V V µA pF V V All data sheets are subject to change without notice 3 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory PARAMETER Output Leakage Current DAC OUTPUTS4 Propogation Delay7 Settling Time8, 9 Output Capacitance AC Feedthrough SWITCHING CHARACTERISTICS4, 10 Write to Data Strobe Time Data Valid to Strobe Set-up Time Data Valid to Strobe Hold Time DAC Select to Strobe Set-Up Time DAC Select to Strobe Hold Time Write Select to Strobe Set-Up Time Write Select to Strobe Hold Time Read to Data Strobe Width Data Strobe to Output Valid Time Output Data Deselect Time Read Select to Strobe Set-Up Time Read Select to Strobe Hold Time POWER SUPPLY Voltage Range Supply Current11 Supply Current12 VDD IDD IDD +25°C tDS1 tDS2 tDSU tDH tAS tAH tWSU tWH tRDS tCO tOTD tRSU tRH +25°C +25°C tPD ts COUT FT SYMBOL ILKG 8408 SUBGROUPS 1 2, 3 9, 10, 11 9, 10, 11 MIN ------54 90 145 150 175 10 0 0 0 0 220 350 320 430 200 270 0 0 4.5 ---TYP ±0.005 ±0.075 150 190 ------------------------MAX ±1.0 ±10.0 180 250 30 50 ------------------5.5 50 1.0 1.5 ns ns V µA mA ns ns ns ns ns ns ns ns ns dB ns ns ns pF UNIT µA TABLE 4. 8408 SPECIFICATIONS (VDD = +5 V; VREF = ±10V; VOUTA, B, C, D = 0V, TA = -55 TO 125 °C UNLESS OTHERWISE NOTED) TEST CONDITION +25°C -55 to 125°C DAC latches All “0s” DAC latches All “1s” 20 VP-P @ F = 100 kHz 9, 10, 11 9, 10, 11 9, 10, 11 9 10, 11 9 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9 10, 11 9 10, 11 9 10, 11 9, 10, 11 9, 10, 11 1, 2, 31 1, 2, 3 1 2, 3 -55 to 125°C +25°C -55 to 125°C Memory -55 to 125°C +25°C -55 to 125°C +25°C -55 to 125°C -55 to 125°C 08.20.02 REV 1 All data sheets are subject to change without notice 4 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory 1. This is an end-point linearity specification. 2. Guaranteed to be monotonic over the full operating temperature range. 3. ppm/°C of FSR (FSR = Full Scale Range = VREF -1 LSB). 4. Guaranteed by design. 5. All Digital Inputs = 0V; VREF = +10V. 6. Logic Inputs are MOS gates. Typical input current at +25°C is less than 10 nA. 7. From Digital Input to 90% of final analog output current. 9. Extrapolated: ts (1/2 LSB) = tPD + 6.2τ where τ = the measured first constant of the final RC decay. 10.See Timing Diagram 11. All Digital Inputs “0” or VDD. 12.All Digital Inputs VIH or VIL 8. Digital Inputs = 0V to VDD or VDD to 0V. 8408 Memory 08.20.02 REV 1 All data sheets are subject to change without notice 5 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory FIGURE 1. TIMING DIAGRAM 8408 Memory FIGURE 2. SUPPLY CURRENT VS. LOGIC LEVEL 08.20.02 REV 1 All data sheets are subject to change without notice 6 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory CIRCUIT INFORMATION 8408 The 8408 combines four identical 8-bit CMOS DACs onto a single monolithic chip. Each DAC has its own reference input, feedback resistor, and on-board data latches. It also features a read/write function that serves as an accessible memory location for digital-input data words. The DAC’s three-state readback drivers place the data word back onto the data bus. D/A CONVERTER SECTION Each DAC contains a highly stable, silicon-chromium, thin-film, R-2R resistor ladder network and eight pairs of current steering switches. These switches are in series with each ladder resistor and are single-pole, double-throw NMOS transistors; the gates of these transistors are controlled by CMOS inverters. Figure 3 shows a simplified circuit of the R-2R resistor ladder section, and Figure 4 shows an approximate equivalent switch circuit. The current through each resistor leg is switched between IOUT 1 and IOUT 2. This maintains a constant current in each leg, regardless of the digital input logic states. Each transistor switch has a finite “ON” resistance that can introduce errors to the DAC’s specified performance. These resistances must be accounted for by making the voltage drop across each transistor equal to each other. This is done by binarily scaling the transistor’s “ON” resistance from the most significant bit (MSB) to the least significant bit (LSB). With 10 volts applied at the reference input, the current through the MSB switch is 0.5 mA, the next bit is 0.25 mA, etc.; this maintains a constant 10 mV drop across each switch and the converter’s accuracy is maintained. It also results in a constant resistance appearing at the DAC’s reference input terminal; this allows the DAC to be driven by a voltage or current source, ac or dc, of positive or negative polarity. Shown in Figure 5 is an equivalent output circuit for DAC A. The circuit is shown with all digital inputs high. The leakage current source is the combination of surface and junction leakages to the substrate. The 1/256 current source represents the constant 1-bit current drain through the ladder terminating resistor. The situation is reversed with all digital inputs low, as shown in Figure 6. The output capacitance is code dependent, and therefore, is modulated between the low and high values. Memory 08.20.02 REV 1 All data sheets are subject to change without notice 7 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory 8408 FIGURE 3. SIMPLIFIED D/A CIRCUIT OF 8408 FIGURE 4. N-CHANNEL CURRENT STEERING SWITCH Memory FIGURE 5. EQUIVALENT DAC CIRCUIT (AII DIGITAL INPUTS HIGH) 08.20.02 REV 1 All data sheets are subject to change without notice 8 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory 8408 FIGURE 6. EQUIVALENT DAC CIRCUIT (AII DIGITAL INPUTS LOW) DIGITAL SECTION Figure 7 shows the digital input/output structure for one bit. The digital WR, WR, and RD controls shown in the figure are internally generated from the external A/B, R/W, DS1, and DS2 signals. The combination of these signals decide which DAC is selected. The digital inputs are CMOS inverters, designed such that TTL input levels (2.4 V and 0.8 V) are converted into CMOS logic levels. When the digital input is in the region of 1.2 V to 1.8 V, the input stages operate in their linear region and draw current from the +5 V supply (see Typical Supply Current vs. Logic Level curve on page 6). It is recommended that the digital input voltages be as close to VDD and DGND as is practical in order to minimize supply currents. This allows maximum savings in power dissipation inherent with CMOS devices. The three-state readback digital output drivers (in the active mode) provide TTL-compatible digital outputs with a fan-out of one TTL load. The three state digital readback leakage-current is typically 5 nA. Memory FIGURE 7. DIGITAL INPUT/OUTPUT STRUCTURE 08.20.02 REV 1 All data sheets are subject to change without notice 9 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory NTERFACE LOGIC SECTION DAC Operating Modes • All DACs in HOLD MODE. • DAC A, B, C, or D individually selected (WRITE MODE). • DAC A, B, C, or D individually selected (READ MODE). • DACs A and C simultaneously selected (WRITE MODE). • DACs B and D simultaneously selected (WRITE MODE). 8408 DAC Selection: Control inputs, DS1, DS2, and A/B select which DAC can accept data from the input port (see Mode Selection Table). Mode Selection: Control inputs DS and R/W control the operating mode of the selected DAC. Write Mode: When the control inputs DS and R/W are both low, the selected DAC is in the write mode. The input data latches of the selected DAC are transparent, and its analog output responds to activity on the data inputs DB0–DB7. Hold Mode: The selected DAC latch retains the data that was present on the bus line just prior to DS or R/W going to a high state. All analog outputs remain at the values corresponding to the data in their respective latches. Read Mode: When DS is low and R/W is high, the selected DAC is in the read mode, and the data held in the appropriate latch is put back onto the data bus. Memory 08.20.02 REV 1 All data sheets are subject to change without notice 10 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory TABLE 4. MODE SELECTION TABLE 8408 Memory BASIC APPLICATIONS Some basic circuit configurations are shown in Figures 8 and 9. Figure 8 shows the 8408 connected in a unipolar configuration (2-Quadrant Multiplication), and Table 5 shows the Code Table. Resistors R1, R2, R3, and R4 are used to trim full scale output. Full-scale output voltage = VREF –1 LSB = VREF (1–2–8) or VREF x (255/256) with all digital inputs high. Low temperature coefficient (approximately 50 ppm/°C) resistors or trimmers should be selected if used. Full scale can also be adjusted using VREF voltage. This will eliminate resistors R1, R2, R3, and R4. In many applications, R1 through R4 are not required, and the maximum gain error will then be that of the DAC. Each DAC exhibits a variable output resistance that is code dependent.This produces a code-dependent, differential nonlinearity term at the amplifier’s output which can have a maximum value of 0.67 times the amplifier’s offset voltage. This differential nonlinearity term adds to the R-2R resistor ladder differential-nonlinearity; the output may no longer be monotonic. To maintain monotonicity and minimize gain and linearity errors, it is recommended that the op amp offset voltage be adjusted to less than 10% of 1 LSB (1 LSB = 2–8 x VREF or 1/256 x VREF), or less than 3.9 mV over the operating temperature range. Zeroscale output voltage (with all digital inputs low) may be adjusted using the op amp offset adjustment. Capacitors C1, C2, C3, and C4 provide phase compensation and help prevent overshoot and ringing when using high speed op amps. Figure 9 shows the recommended circuit configuration for the bipolar operation (4-quadrant multiplication), and Table 6 shows the Code Table. Trimmer resistors R17, R18, R19, and R20 are used only if gain error adjustments are required and range between 50 Ω and 1000 Ω. Resistors R21, R22, R23, and R24 will range between 50 Ω and 500 Ω. If these resistors are used, it is essential that resistor pairs R9–R13, R10–R14, R11–R15, R12–R16 are matched both in value and tempco. They should be within 0.01%; wire wound or metal foil types are preferred for best temperature coefficient matching. The circuits of Figure 8 and 9 can either be used as a fixed reference D/A converter, or as an attenuator with an ac input voltage. 08.20.02 REV 1 All data sheets are subject to change without notice 11 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory TABLE 5. UNIPOLAR BINARY CODE TABLE (REFER TO FIGURE 8) 8408 Memory FIGURE 8. QUAD DAC UNIPOLAR OPERATION (2-QUADRANT MULTIPLICATION) 08.20.02 REV 1 All data sheets are subject to change without notice 12 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory FIGURE 9. QUAD DAC BIPOLAR OPERATION (4-QUADRANT MULTIPLICATION) 8408 Memory TABLE 6. BIPOLAR (OFFSET BINARY) CODE TABLE (REFER TO FIGURE 9) 08.20.02 REV 1 All data sheets are subject to change without notice 13 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory APPLICATION HINTS 8408 General Ground Management: AC or transient voltages between AGND and DGND can appear as noise at the 8408’s analog output. Note that in Figures 5 and 6, IOUT2A/IOUT2B and IOUT 2C/IOUT 2D are connected to AGND. Therefore, it is recommended that AGND and DGND be tied together at the 8408 socket. In systems where AGND and DGND are tied together on the backplane, two diodes (1N914 or equivalent) should be connected in inverse parallel between AGND and DGND. Write Enable Timing: During the period when both DS and R/W are held low, the DAC latches are transparent and the analog output responds directly to the digital data input. To prevent unwanted variations of the analog output, the R/W should not go low until the data bus is fully settled (DATA VALID). SINGLE SUPPLY, VOLTAGE OUTPUT OPERATION Memory The 8408 can be connected with a single +5 V supply to produce DAC output voltages from 0 V to +1.5 V. In Figure 10, the 8408 R-2R ladder is inverted from its normal connection. A +1.500 V reference is connected to the current output pin 4 (IOUT 1A), and the normal VREF input pin becomes the DAC output. Instead of a normal current output, the R-2R ladder outputs a voltage. The OP-490, consisting of four precision low power op amps that can operate its inputs and outputs to zero volts, buffers the DAC to produce a low impedance output voltage from 0 V to +1.5 V full-scale. Table 7 shows the code table. With the supply and reference voltages as shown, better than 1/2 LSB differential and integral nonlinearity can be expected. To maintain this performance level, the +5 V supply must not drop below 4.75 V. Similarly, the reference voltage must be no higher than 1.5 V. This is because the CMOS switches require a minimum level of bias in order to maintain the linearity performance. TABLE 7. SINGLE SUPPLY BINARY CODE TABLE (REFER TO FIGURE 10) 08.20.02 REV 1 All data sheets are subject to change without notice 14 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory FIGURE 10. UNIPOLAR SUPPLY, VOLTAGE OUTPUT DAC OPERATION 8408 Memory FIGURE 11. A DIGITALLY PROGRAMMABLE UNIVERSAL ACTIVE FILTER 08.20.02 REV 1 All data sheets are subject to change without notice 15 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory A DIGITALLY PROGRAMMABLE ACTIVE FILTER 8408 A powerful D/A converter application is a programmable active filter design as shown in Figure 11. The design is based on the state-variable filter topology which offers stable and repeatable filter characteristics. DAC B and DAC D can be programmed in tandem with a single digital byte load which sets the center frequency of the filter. DAC A sets the Q of the filter. DAC C sets the gain of the filter transfer function. The unique feature of this design is that varying the gain of filter does not affect the Q of the filter. Similarly, the reverse is also true. This makes the programmability of the filter extremely reliable and predictable. Note that low-pass, high-pass, and bandpass outputs are available. This sophisticated function is achieved in only two IC packages. The network analyzer photo shown in Figure 12 superimposes five actual bandpass responses ranging from the lowest frequency of 75 Hz (1 LSB ON) to a full-scale frequency of 19.132 kHz (all bits ON), which is equivalent to a 256 to 1 dynamic range. The frequency is determined by fC = 1/2πRC where R is the ladder resistance (RIN) of the 8408, and C is 1000 pF. Note that from device to device, the resistance RIN varies. Thus some tuning may be necessary. Memory FIGURE 12. PROGRAMMABLE ACTIVE FILTER BAND-PASS FREQUENCY RESPONSE All components used are available off-the-shelf. Using low drift thin-film resistors, the 8408 exhibits very stable performance over temperature. The wide bandwidth of the OP-470 produces excellent high frequency and high Q response. In addition, the OP470’s low input offset voltage assures an unusually low dc offset at the filter output. 08.20.02 REV 1 All data sheets are subject to change without notice 16 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory FIGURE 13. A DIGITALLY PROGRAMMABLE, LOW-DISTORTION SINEWAVE OSCILLATOR 8408 Memory A LOW-DISTORTION, PROGRAMMABLE SINEWAVE OSCILLATOR By varying the previous state-variable filter topology slightly, one can obtain a very low distortion sinewave oscillator with programmable frequency feature as shown in Figure 13. Again, DAC B and DAC D in tandem control the oscillating frequency based on the relationship fC = 1/2πRC. Positive feedback is accomplished via the 82.5 kΩ and the 20 kΩ potentiometer. The Q of the oscillator is determined by the ratio of 10 kΩ and 475Ω in series with the FET transistor, which acts as an automatic gain control variable resistor. The AGC action maintains a very stable sinewave amplitude at any frequency. Again, only two ICs accomplish a very useful function. At the highest frequency setting, the harmonic distortion level measures 0.016%. As the frequencies drop, distortion also drops to a low of 0.006%. At the lowest frequency setting, distortion came back up to a worst case of 0.035% 08.20.02 REV 1 All data sheets are subject to change without notice 17 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory 8408 Memory 28 PIN RAD-PAK® FLAT PACKAGE SYMBOL MIN A b c D E E1 E2 E3 e L Q S1 N 0.360 0.062 0.000 0.190 0.015 0.004 -0.380 -0.180 0.030 DIMENSION NOM 0.207 0.017 0.005 0.720 0.410 -0.250 0.080 0.050 BSC 0.370 0.073 0.027 28 0.380 0.081 -MAX 0.224 0.022 0.009 0.740 0.420 0.440 --- F28-02 Note: All dimensions in inches 08.20.02 REV 1 All data sheets are subject to change without notice 18 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory Important Notice: 8408 These data sheets are created using the chip manufacturers published specifications. Maxwell Technologies verifies functionality by testing key parameters either by 100% testing, sample testing or characterization. The specifications presented within these data sheets represent the latest and most accurate information available to date. However, these specifications are subject to change without notice and Maxwell Technologies assumes no responsibility for the use of this information. Maxwell Technologies’ products are not authorized for use as critical components in life support devices or systems without express written approval from Maxwell Technologies. Any claim against Maxwell Technologies must be made within 90 days from the date of shipment from Maxwell Technologies. Maxwell Technologies’ liability shall be limited to replacement of defective parts. Memory 08.20.02 REV 1 All data sheets are subject to change without notice 19 ©2002 Maxwell Technologies All rights reserved. Quad 8-Bit Multiplying CMOS D/A Converter with Memory Product Ordering Options 8408 Model Number 8408 RP F X Feature Option Details Screening Flow S = Maxwell Class S B = Maxwell Class B I = Industrial (testing @ -55°C, +25°C, +125°C) E = Engineering (testing @ +25°C) Memory Package F = Flat Pack Radiation Feature RP = RAD-PAK® package Base Product Nomenclature Quad 8-Bit Multiplying CMOS D/A Converter with Memory 08.20.02 REV 1 All data sheets are subject to change without notice 20 ©2002 Maxwell Technologies All rights reserved.