OP284ARPLS

OP284A Dual Operational Amplifier VCC OP284A TP RB1 R3 R4 QB6 QB5 RB3 RB4 R11 Q11 Q7 Q1 -IN Q3 Q4 Q2 +IN Q5 Q9 Q8 Q12 QB9 QB10 Q10 CC2 CFF R6 Q16 Q17 Flat Pack JB1 QL1 QL2 OUT CO Q6 Q18 QB2 QB3 R7 Q13 QB4 JB2 CC1 QB7 Q14 R9 QB8 R8 R10 Q15 CB1 N+ M P+ RB2 OP284A QB1 R1 R2 R5 VEE Leadless Chip Carrier (LCC) Logic Diagram Memory FEATURES: • RAD-PAK® radiation-hardened against natural space • radiation • Package: - 8-pin RAD-PAK® flat pack - 16-pin RAD-PAK® Leadless Chip Carrier (LCC) pack • Single-Supply Operation • Wide Bandwidth: 4 MHz • Low Offset Voltage: 65uV • Unity-Gain Stable • High Slew Rate: 4.0 V/us • Low Noise: 3.9 nV/(Hz)½ DESCRIPTION: Maxwell Technologies’ OP284A is a dual single-supply, 4 MHz bandwidth amplifier featuring rail-to-rail inputs and outputs. Using Maxwell Technologies’ radiation-hardened RADPAK® technology, it is guaranteed to operate from +3 to +36 (or ±1.5 to ±18) volts and will function with a single supply as low as +1.5 volts. This amplifier is superb for single supply applications requiring both ac and precision dc performance. The combination of bandwidth, low noise and precision makes the OP284A useful in a wide variety of applications, including filters and instrumentation. Other applications for this amplifier include portable telecom equipment, power supply control and protection, and as an amplifier or buffer for transducers with wide output ranges. The ability to swing rail-to-rail at both the input and output enables designers to build multi-stage filters in single-supply systems and to maintain high signal-to-noise ratios. Maxwell Technologies' patented RAD-PAK® packaging technology incorporates radiation shielding in the microcircuit package. It eliminates the need for box shielding while providing the required radiation shielding for a lifetime in orbit or space mission. This product is available with screening up to Class S. 07.16.09 Rev 2 All data sheets are subject to change without notice 1 (858) 503-3300 - Fax: (858) 503-3301 - www.maxwell.com ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier TABLE 1. FLAT PACK PINOUT DESCRIPTION PIN 1, 7 2, 6 3, 5 4 8 SYMBOL OUT A, B -IN A, B +IN A, B VV+ Outputs Negative Inputs Positive Inputs Ground Supply Voltage DESCRIPTION OP284A TABLE 2. LEADLESS CHIP CARRIER (LCC) PINOUT DESCRIPTION PIN 1, 13 3, 11 5, 9 7 15 SYMBOL OUT A, B -IN A, B +IN A, B VV+ Outputs Negative Inputs DESCRIPTION Memory Positive Inputs Ground Supply Voltage TABLE 3. OP284A ABSOLUTE MAXIMUM RATINGS PARAMETER Supply Voltage Input Voltage Differential Input Voltage1 Output Short-Circuit Duration to GND Storage Temperature Operating Temperature Junction Temperature Package Weight Thermal Impedance TS TA TJ -65 -40 -65 --SYMBOL VCC VI VDIF MIN ---Indefinite +150 +125 +150 0.75 6.48 °C °C °C Grams °C/W MAX ±18 ±18 ±0.6 UNIT V V V ΘJC 1. For input voltages greater than 0.6 volts, the input current should be limited to less 5 mA to prevent degradation or destruction of the input devices. TABLE 4. DELTA LIMITS PARAMETER ICC VARIATION ±10% of specified value in Table 5 07.16.09 Rev 2 All data sheets are subject to change without notice 2 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier OP284A TABLE 5. OP284A ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, VOUT = 0V, RS = 50Ω, RL = 100KΩ, VCM = 0V, TA = -40°C TO +125°C UNLESS OTHERWISE SPECIFIED.) PARAMETER Input offset voltage Average offset voltage drift1 Offset voltage match1 Input bias current Input offset current Input bias current drift1 Input voltage range Common mode rejection ratio Output current SYMBOL VIO +25°C -40 to +125°C VIOTC RL=2kΩ TEST CONDITIONS SUBGROUPS 1 2, 3 1, 2, 3 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 1, 2, 3 4,5,6 4 1 2, 3 1 2, 3 1 2, 3 1 2, 3 1, 2, 3 1, 2, 3 1 1 1 1, 2, 3 4 5,6 4 5,6 ----1.80 2.25 90 90 -----VCM = -15V to +15V, TA=25°C +IO -IO Quiescent power supply current per amplifier +ICC -ICC VOUT = -10V, 1ms pulse, TA=25°C VOUT = -10V, 1ms pulse VOUT = +10V, 1ms pulse, TA=25°C VOUT = -10V, 1ms pulse IOUT = 0mA VS=±18V, TA=25°C IOUT = 0mA VS=±18V IOUT = 0mA VS=±18V, TA=25°C IOUT = 0mA VS=±18V Power supply rejection ratio +PSRR VS=±2V to ±18V -PSRR VS=±2V to ±18V Low frequency, peak-topeak noise1 Input noise voltage density1 Input noise current density1 Power consumption1,2 Large signal voltage gain Enp-p En In PC 0.1Hz to 10Hz, RL=2kΩ, CL=50pF, TA=+25°C RS=20Ω, fO=1kHz, RL=2kΩ, CL=50pF, TA=+25°C RS=20MΩ, fO=1kHz, RL=2kΩ, CL=50pF, TA=+25°C +10V, IOUT=0mA, RL=2kΩ +10V, RL=2.0kΩ -AVOL -10V, RL=2.0kΩ,TA=25°C -10V, RL=2.0kΩ -15 86 80 10 5 MIN -100 -200 --350 -575 -35 -50 TYP -----------------------0.30 3.9 0.4 MAX 100 200 2 100 200 350 575 35 50 200 15 -----10 -5 1.80 2.25 -------81 150 75 150 75 V/mV dB dB µ Vp-p nV/ (Hz)½ pA/ (Hz)½ mW V/mV mA mA mA nA nA nA nA pA/°C V dB dB mA µ V/°C µV UNIT µV ∆VIO |VIO (max) - VIO (min)|, +25°C |VIO (max) - VIO (min)|, -40 to +125°C IB IOS IIBTC IVR CMRR VCM = -14V to +14V RS = 50Ω, +25°C RS = 50Ω, -40 to +125°C RS =50Ω, +25°C RS = 50Ω, -40 to +125°C RS = 50Ω Memory +AVOL +10V, RL=2.0kΩ,TA=25°C 07.16.09 Rev 2 All data sheets are subject to change without notice 3 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier OP284A SUBGROUPS 4,5,6 4,5,6 4 4 9 4 4,5,6 4,5,6 MIN 14.8 -----2.4 2.4 TYP --4.25 35 --4.0 4.0 MAX --14.8 --5 50 --UNIT V V MHz kHz µs Degrees V/µ s V/µ s TABLE 5. OP284A ELECTRICAL CHARACTERISTICS (V+ = 15V, V- = -15V, VOUT = 0V, RS = 50Ω, RL = 100KΩ, VCM = 0V, TA = -40°C TO +125°C UNLESS OTHERWISE SPECIFIED.) PARAMETER Output voltage swing Gain bandwidth product1 Full power bandwidth1,3 Settling time Phase margin Slew rate SYMBOL +VOUT1 IL=1.0mA -VOUT1 IL=1.0mA GBWP VO=200mV, RL=2.0kΩ, CL=50pF, TA=+25°C FPBW VPEAK=29vp-p, RL=2.0kΩ, CL=50pF, TA=+25°C, 1% distortion tS FO +SR -SR 1. Guaranteed by design. 2. Power consumption is based upon quiescent supply current maximum test limit. No load on outputs. 3. Full power bandwidth is based on slew rate measurement using FBBW = slew rate/(2PVPEAK). AV=+1.0, CL=50pF, RL=2.0kΩ To 0.01%, 10V step AV=1.0, CL=50pF, RL=2.0kΩ, TA=+25°C CL=50pF, RL=2.0kΩ CL=50pF, RL=2.0kΩ TEST CONDITIONS Memory 07.16.09 Rev 2 All data sheets are subject to change without notice 4 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 1. INPUT OFFSET VOLTAGE DISTRIBUTION OP284A FIGURE 4. INPUT OFFSET VOLTAGE DRIFT DISTRIBUTION FIGURE 2. INPUT OFFSET VOLTAGE DISTRIBUTION FIGURE 5. INPUT OFFSET VOLTAGE DRIFT DISTRIBUTION Memory FIGURE 3. INPUT OFFSET VOLTAGE DISTRIBUTION FIGURE 6. BIAS CURRENT VS. TEMPERATURE 07.16.09 Rev 2 All data sheets are subject to change without notice 5 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 7. INPUT BIAS CURRENT VS. COMMON-MODE VOLTAGE OP284A FIGURE 9. SUPPLY CURRENT VS. TEMPERATURE FIGURE 10. SUPPLY CURRENT VS. SUPPLY VOLTAGE FIGURE 8. OUTPUT VOLTAGE TO SUPPLY RAIL VS. LOAD CURRENT Memory FIGURE 11. SHORT CIRCUIT CURRENT VS. TEMPERATURE 07.16.09 Rev 2 All data sheets are subject to change without notice 6 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 12. OPEN-LOOP GAIN AND PHASE VS. FREQUENCY (NO LOAD) OP284A FIGURE 14. OPEN-LOOP GAIN AND PHASE VS. FREQUENCY (NO LOAD) FIGURE 13. OPEN-LOOP GAIN AND PHASE VS. FREQUENCY (NO LOAD) FIGURE 15. OPEN-LOOP GAIN VS. TEMPERATURE Memory 07.16.09 Rev 2 All data sheets are subject to change without notice 7 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 16. CLOSED-LOOP GAIN VS. FREQUENCY (2KW LOAD) OP284A FIGURE 18. CLOSED-LOOP GAIN VS. FREQUENCY (2KW LOAD) FIGURE 19. OUTPUT IMPEDANCE VS. FREQUENCY FIGURE 17. CLOSED-LOOP GAIN VS. FREQUENCY (2KW LOAD) Memory 07.16.09 Rev 2 All data sheets are subject to change without notice 8 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 20. OUTPUT IMPEDANCE VS. FREQUENCY OP284A FIGURE 23. MAXIMUM OUTPUT SWING VS. FREQUENCY FIGURE 21. OUTPUT IMPEDANCE VS. FREQUENCY FIGURE 24. CMMR VS. FREQUENCY Memory FIGURE 22. MAXIMUM OUTPUT SWING VS. FREQUENCY 07.16.09 Rev 2 All data sheets are subject to change without notice 9 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 25. PSRR VS. FREQUENCY OP284A FIGURE 27. SLEW RATE VS. TEMPERATURE FIGURE 28. VOLTAGE NOISE DENSITY VS. FREQUENCY FIGURE 26. SMALL SIGNAL OVERSHOOT VS. CAPACITIVE LOAD Memory FIGURE 29. CURRENT NOISE DENSITY VS. FREQUENCY 07.16.09 Rev 2 All data sheets are subject to change without notice 10 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 30. SETTLING TIME VS. STEP SIZE OP284A FIGURE 33. 0.1 HZ TO 10 HZ NOISE FIGURE 31. SETTLING VS. STEP SIZE FIGURE 34. CHANNEL SEPARATION VS. FREQUENCY Memory FIGURE 32. 0.1 HZ TO 10 HZ NOISE 07.16.09 Rev 2 All data sheets are subject to change without notice 11 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier FIGURE 35. SMALL SIGNAL TRANSIENT RESPONSE OP284A FIGURE 38. SMALL SIGNAL TRANSIENT RESPONSE FIGURE 39. TOTAL HARMONIC DISTORTION VS. FREQUENCY FIGURE 36. SMALL SIGNAL TRANSIENT RESPONSE Memory FIGURE 37. SMALL SIGNAL TRANSIENT RESPONSE 07.16.09 Rev 2 All data sheets are subject to change without notice 12 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier OP284A Memory 8-PIN RAD-PAK® FLAT PACKAGE SYMBOL MIN A b c D E E1 E2 E3 e L Q S1 N 0.338 0.021 0.005 0.119 0.010 0.004 0.250 0.250 -0.125 0.030 DIMENSION NOM 0.132 0.017 0.005 0.255 0.255 -0.145 0.040 0.050 BSC 0.348 0.025 0.019 8 0.358 0.045 -MAX 0.149 0.022 0.009 0.260 0.260 0.290 --- Note: All dimensions in inches 07.16.09 Rev 2 All data sheets are subject to change without notice 13 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier OP284A 16-PIN RAD-PAK® LCC PACKAGE SYMBOL MIN A b D D1 S1 e A1 N 0.095 0.123 0.018 0.245 DIMENSION NOM 0.135 0.020 0.250 0.150 BSC 0.050 BSC 0.050 BSC 0.105 16 0.116 MAX 0.150 0.025 0.260 Memory Note: All dimensions in inches. 07.16.09 Rev 2 All data sheets are subject to change without notice 14 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier Important Notice: OP284A These data sheets are created using the chip manufacturer’s published specifications. Maxwell Technologies verifies functionality by testing key parameters either by 100% testing, sample testing or characterization. The specifications presented within these data sheets represent the latest and most accurate information available to date. However, these specifications are subject to change without notice and Maxwell Technologies assumes no responsibility for the use of this information. Maxwell Technologies’ products are not authorized for use as critical components in life support devices or systems without express written approval from Maxwell Technologies. Any claim against Maxwell Technologies must be made within 90 days from the date of shipment from Maxwell Technologies. Maxwell Technologies’ liability shall be limited to replacement of defective parts. Memory 07.16.09 Rev 2 All data sheets are subject to change without notice 15 ©2009 Maxwell Technologies All rights reserved. Dual Operational Amplifier Product Ordering Options Model Number OP284A RP F X Feature OP284A Option Details Screening Flow Monolithic S = Maxwell Class S B = Maxwell Class B I = Industrial (testing @ -40°C, +25°C, +125°C) E = Engineering (testing @ +25°C) Memory Package F = Flat Pack L = Leadless Chip Carrier (LLC) Radiation Feature RP = RAD-PAK® package Base Product Nomenclature Operational Amplifier 07.16.09 Rev 2 All data sheets are subject to change without notice 16 ©2009 Maxwell Technologies All rights reserved.